Reset All Features - Clifford IntelliGuard Millennia Owner's Manual

Dei clifford intelliguard millennia car alarms: owners manual

Table of Contents

NOTE: Some features, such as AutoStart (column 2, row 4) used with the optional IntelliStart 4 accessory, have

multiple settings. Simply reselect the feature additional times to progress through each possible setting.

7. You may now select another feature or exit program mode:

a. To select another feature in that same column, repeat step 5 within the next 5 seconds (after 5 seconds, 3 chirps mean you are back to the "Feature

Select" position).

b. To select a different feature column, go to step 4.

c. To exit program mode, turn the ignition off (you'll hear 3 chirps and the LED will turn off). If driving, just wait 60 seconds and the system will

automatically exit program mode.

If you make an error, just turn off the ignition and start again.

In the following example, we will change the settings of three different features in just one programming session: We will turn on the Lock upon

AutoArming feature to set your vehicle's power locks to automatically engage whenever the system AutoArms, turn off remote controlled valet mode and

turn off the FACT anti-falsing feature:

1. Enter program mode as previously noted (ignition on, enter your valet code, press and hold the ✱ button on the PlainView 2 switch until you hear

a chirp).

2. Since the Lock upon AutoArming feature is in column 3, row 2 of the Table, go to column 3 by pressing the blank button on the PlainView 2 switch

three times. Wait for the 3-chirp/column 3 confirmation. Then press the ✱ button twice (you'll hear a chirp each time you press the ✱ button).

After a brief pause, you'll hear 2 chirps to confirm that Lock upon AutoArming is now on.

3. Since FACT is also in column 3, there is no need to reselect column 3. Therefore, you can go straight to the row selection. Select row 4 by pressing

the ✱ button four times. After a brief pause, you'll hear one chirp to confirm that FACT is now off.

4. You'll note that the Remote valet mode feature is at column 2, row 3. To change to column 2, press the blank button twice, then wait for the

2-chirp/column 2 confirmation. Press the ✱ button three times to select row 3. After a brief pause, you'll hear one chirp to confirm that the Remote

valet mode feature is now turned off.

5. To exit the program mode, turn the ignition off. You'll hear 3 chirps to confirm program mode exit.

If you wish to reset all the user-selectable features to their normal factory presets, you can do so simply by choosing the Reset all features selection (column

1, row 7) on the Table of User-Selectable Features. If you do so, all features — except the programmed remote controls and your valet code — will be reset

to the factory settings that are indicated in

in column 2, row 6. To reset your valet code, use the Set a new valet/disarming PIN code feature in column 2, row 7.

1 ✱ press

2 ✱ presses

Play Personalized Siren Sounds**:

3 ✱ presses

4 ✱ presses

5 ✱ presses

6 ✱ presses

Reset all features (except remotes

7 ✱ presses

and valet code) to factory settings

NOTE 1: Press button 1 of the new MASTER 5-button remote control. You will hear one chirp. Immediately press button

1 again. You will hear two chirps to confirm that the new remote control has been added.

NOTE 2: Selection of this feature will cause the system to sound a few seconds of siren sound #1. Press the blank

button to turn on this sound or the ✱ button to turn it off. The system will then sound a few seconds of sound #2.

Repeat: blank=ON, ✱=OFF for each of the six sounds.

NOTE 3: You'll hear two chirps to indicate all remotes have been cleared from memory. You must now add

new/existing remotes with the "Add master remote control" feature and/or the "Other vehicle's remote" feature.

NOTE 4: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the

ignition (you'll hear 3 chirps to confirm program mode exit). You MUST now turn the ignition back on and then

type on the Table of User-Selectable Features. To reset all remote controls, use the Clear all remotes feature

BOLD

Table of User-Selectable Features

1 blank press

Add master remote control

NOTE 1

Personalized Siren Sounds**

NOTE 2

trigger only/always (1/2 chirps)

Siren duration: 30/60/90sec.**

AutoStart*: both off/both on/temp

(1/2/3 chirps)

AutoLock: off/on

AutoUnLock: off/on

Set a new valet/disarming PIN code

Reset All Features

2 blank presses

Chirps: off/loud/quiet

(1/2/3 chirps)

SilentNight: off/on

Valet mode entry/exit via the

remote control: off/on

only/battery only (1/2/3/4 chirps)

BlackJax anti-carjacking: off/on

Clear all remotes

NightVision: off/on/on without post-

parking illumination (1/2/3 chirps)

NOTE 3

NOTE 4

3 blank presses

AutoArming: off/on

Lock upon AutoArming: off/on

AutoArming entry delay: off/on

FACT: off/on

Headlight duration: 1sec. – 4.25

min. (10sec.) NOTE 5

NightVision activation: lighter/

twilight/darker (1/2/3 chirps)

4 blank presses

NOTE 6 — Add companion remote:

arm/disarm (1 then 2 chirps)