Necchi NC-204D Instruction Manual
  1. Manuals
  2. Brands
  3. Necchi Manuals
  4. Sewing Machine
  5. NC-204D
  6. Instruction manual

Necchi NC-204D Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Instruction Manual
NC-204D

Advertisement

Table of Contents
loading

Related Manuals for Necchi NC-204D

Summary of Contents for Necchi NC-204D

  • Page 1 Instruction Manual NC-204D...
  • Page 3 Important safety instructions When using an electrical appliance, basic safety should always be followed, including the following: Read all instructions before using this sewing machine. DANGER - To reduce the risk of electric shock: 1. An appliance should never be left unattended when plugged in. 2.
  • Page 4 15. Never use the machine if the air vents are blocked, keep the air vents of the machine and the foot pedal free from dust, fusel and leftovers. 16. The machine must only be used with designated foot controller, in order to avoid a hazard.

  • Page 5: Table Of Contents

    Contents Machine Introduction Principal parts of the machine ....................1 Accessories ..........................2 Standard ..............................2 Connecting machine to power source ................... 3 Polarized plug information ........................3 Foot control ............................3 Foot controller with needle up and down feature ...................
  • Page 6 Sewing Basics Straight stitch ......................... 40 Changing the needle position ......................40 Zigzag stitch ........................... 41 Starting to sew ........................42 Useful skills ..........................44 Reverse sewing ............................ 44 Sewing curves ............................44 Sewing corners ............................ 45 Sewing stretch fabrics .......................... 45 Sewing thin fabrics ..........................
  • Page 7 Scallop hem ............................71 Cording............................ 72 Single cording ............................72 Striple cording ............................72 Narrow hemming ........................73 Walking foot ..........................74 Twin needle ..........................75 Maintenance and Trouble shooting Maintenance ........................... 78 Clean the hook ............................. 78 Clean the machine surface ........................78 Warning Function ........................

  • Page 8: Machine Introduction

    Machine Introduction...

  • Page 9: Principal Parts Of The Machine

    Principal parts of the machine ① Take-up lever ② Presser foot pressure dial ③ Operation buttons ④ Thread cutter ⑤ Sewing table and accessory box ⑥ Tension dial ⑦ Speed adjustment slider ⑧ Bobbin winder spindle ⑨ Bobbin winder stopper ⑩...

  • Page 10: Accessories

    Accessories Most accessories are stored in the accessory box. The electronic buttonhole foot, walking foot, extension table and soft cover can be found aside of the packing styrofoam. v Standard ① All purpose foot (already installed) ② Zipper foot ③ Satin stitch foot ④...

  • Page 11: Connecting Machine To Power Source

    Connecting machine to power source n Attention Always make sure that the machine is unplugged from power source and the main switch is off ("O"), when the machine is not in use and before inserting or removing parts. Before connecting the power supply, make sure that the voltage shown on the rating plate is conforming with your main power.

  • Page 12: Machine Setup

    Machine Setup...

  • Page 13: Sewing Table

    Sewing table Hold the sewing table horizontally, then pull toward the left to remove it from the machine. Attach the sewing table, and then push it to the right. The inside space of the sewing table is used as an accessory box. v Free arm Free-arm sewing is convenient for sewing tubular areas such as pant hems and cuffs.

  • Page 14: Install The Extension Table

    Install the extension table Pull the sewing table and accessory box off by sliding it to the left. Follow the arrow, and stretch the foot of the extension table. Snap (A) of the extension table into (B) of the machine. Adjusting the presser foot pressure The presser foot pressure dial is on the top left of the face plate.

  • Page 15: Winding The Bobbin

    Winding the bobbin Please following the number order and see the corresponding illustrations below. 1. Place the thread and spool holder onto the spool pin. For better sewing quality, choose a proper size of the spool holder for the thread and attach it next to the spool.
  • Page 16 6. Hold the thread tail securely in one hand. Step on the foot control or press the start/ stop button to start winding the bobbin. 7. After the bobbin has wound a few rounds, stop the machine and cut the thread near the hole of the bobbin.

  • Page 17: Inserting The Bobbin

    Inserting the bobbin n Attention Turn the power switch to off ("O"). When inserting or removing the bobbin, the needle and the presser foot must be fully raised. Open the bobbin cover by pushing the release button to the right. ①...

  • Page 18: Threading The Upper Thread

    Threading the upper thread Please following the number order and see the corresponding illustrations below. It is important to carry out the threading correctly to get a quality sewing. Otherwise several problems will occur. 1. Turn the power switch to on ("I"). Raise the presser foot lifter.
  • Page 19 4. Draw the thread from the spool and place the thread in between the upper thread guide. 5. Guide the thread ahead and pull the thread through the pre-tension spring as illustrated. 6. Continue to guide the thread into the silver discs to keep the thread in proper tension.
  • Page 20 10. Lower the presser foot lifter. 11. Lower the needle threader lever slowly and draw the thread through the thread guide as illustrated and then to the right. ① Lever ② Hook pin 12. The needle threader automatically turns to the threading position and the hook pin passes through the needle eye.

  • Page 21: Bringing Up The Bobbin Thread

    Bringing up the bobbin thread When sewing gathering or smocking stitch, bring up the bobbin thread first as below instruction. Hold the upper thread with your left hand. Turn the handwheel towards you (counter- clockwise) to lower the needle down below the needle plate then raise it to bring the bobbin thread up.

  • Page 22: Replacing The Needle

    Replacing the needle Change the needle regularly, especially when it shows signs of wear or if it causes problems. n Attention Turn the power switch to off ("O") when carrying out below operations! Turn the handwheel toward you to raise the needle then loosen the needle clamp screw to remove the needle.

  • Page 23: Matching Needle/Fabric/Thread

    Matching needle/fabric/thread NEEDLE SIZE FABRICS THREAD 65/9 - 75/11 Lightweight fabrics- Light-duty thread in cotton, nylon, polyester or cotton wrapped thin cottons, voile, serge, silk, muslin, polyester. Qiana, interlocks, cotton knits, tricot, jerseys, crepes, woven polyester, shirt & blouse fabrics. 80/12 Medium weight fabrics- Most threads sold are medium...

  • Page 24: Changing The Presser Foot

    Changing the presser foot n Attention Turn the power switch to off ("O"). Always use the proper foot for the selected stitch. The wrong foot can cause the needle to break. v Remove the presser foot Raise the presser foot lifter. Press the back lever to release the presser foot.

  • Page 25: To Raise Or Drop The Feed Dogs

    To raise or drop the feed dogs The drop feed lever can be seen on the base at the back side of the sewing machine. Sliding the drop feed lever to lower or raise the feed dogs. When lever is in raised position, the feed dog will arise automatically when you are sewing.

  • Page 26: Thread Tension

    Thread tension Proper tension setting is important for sewing. There is no single tension setting appropriate for all the stitch functions and fabrics. Basic thread tension setting: "4". Normal thread tension for straight stitch sewing. ① Upper thread ② Bobbin thread ③...

  • Page 27: Instruction

    Instruction...

  • Page 28: Lcd Screen

    LCD screen ① Needle down position ② Needle up position ③ Reverse ④ Auto-lock ⑤ Auto-stop ⑥ Twin needle mode ⑦ Mirror ⑧ Bobbin winding ⑨ Amount of elongation ⑩ Buzzer on Memory mode: ⑪ Buzzer off ⑫ Stitch number/stitch ⑬...

  • Page 29: Operation Buttons

    Operation buttons Start/stop button Press the start/stop button to start machine running. Press the start/stop button again to stop machine. This way you may operate the machine without foot control. Reverse button When the Direct Pattern Group number 1-5 or Regular Pattern Group number 000 is selected, the machine will sew reverse at a low speed if the reverse button is pressed.
  • Page 30 Repeat sewing function (In memory program) Under the memory program, the reverse button is using for repeat sewing. The stitch combination can be sewn continuously if the icon appeared. Press the reverse button to cancel the repeat sewing, machine will sew 3 locking stitches at the end of one complete combination.
  • Page 31 Needle up/down position button With the needle up/down position button, you decide whether the needle stops in the highest or in the lowest position (i.e. in the fabric) when you stop sewing. Note During sewing, press the needle up/down position button, it can not to change the needle position.
  • Page 32 Stitch width adjustment button When you select a stitch, the machine will automatically set the recommended stitch width values which will be shown on the LCD screen. The highlighted value will be erased if the setting be adjusted. The stitch width can be regulated by pressing the stitch width adjustment buttons.
  • Page 33 Twin needle button Press the twin needle button, the LCD screen will display the twin needle icon. The machine automatically reduces the maximum width for the twin needle sewing. Please refer to "Twin needle" chapter for more information. (Page 75) Press the button again to return to single needle sewing.
  • Page 34 Buttonhole adjustment button When the buttonhole stitch is selected, Direct Pattern Group number 0 or Regular Pattern Group number 010-021, the LCD screen will display the buttonhole width size. Continuously press the elongation button to adjust buttonhole size, from M → L → S. Note Use the seam ripper to cut the center of the buttonhole being careful not to cut any...
  • Page 35 Sound button Buzzer turn off: Press the sound button for 2 seconds and when you hear the machine delivering a short beep, the sound will be turned off. Buzzer turn on: When machine is in silent mode, press the button for 2 seconds and it will deliver two short beeps to remind you that the sound is turned on now.

  • Page 36: Selecting Stitch

    Selecting stitch Select the desired stitch from those shown on the stitch pattern plate. ① Stitch pattern plate The LED light will be set at Direct Pattern Group. By pressing the pattern group switch button, LED light will move step by step to select the stitch mode.

  • Page 37: Memory Function Buttons

    Memory function buttons Memory stitch selecting button Use the stitch width adjustment button "+" or "-" to selected the memorized stitch. Edit button Press the edit button to enter the edit mode to edit the stitch length, stitch width, mirror and elongation of the stitches.

  • Page 38: Memory Program

    Memory program You can save frequent-use combining stitches for future use, such as names. Since stored stitches are not lost after the sewing machine is turned off, they can be recalled at any time. Note Multiple stitches selecting from Regular Pattern Group and Alphabet Groups can be combined and sewn together.

  • Page 39: Recalling And Sewing The Memorized Stitches

    Press the desired stitch number directly. (e.g. 117) The selected stitch displays on the LCD screen. Repeat step several times for stitches combination. Up to 40 characters can be combined in one memory module. Press the memory button to save the stitches combination, and return to standard sewing mode.

  • Page 40: Inserting Stitches

    Note The last stitch will be tied off automatically under the memory mode. v Inserting stitches Use the stitch width adjustment button "+" or "-" move prior to the stitch you left out. Then select the pattern group and stitch you would like to add, the stitch number you have selected is displayed, then add the new stitch.

  • Page 41: Clearing Stitches

    v Clearing stitches Use the stitch width adjustment button "+" or "-" to select the stitch that you want to clear. Press the clear button to delete the selected stitch and the next stitch in the back will move forward. ①...
  • Page 42 Stitch Chart...

  • Page 43: Stitch Chart

    Stitch chart v Direct Pattern Group Width(mm) Length(mm) Fuctions Presser Stitch Pattern Foot Auto Manual Auto Manual 0.0~7.0 0.0~4.5 0.0~7.0 0.0~4.5 0.0~7.0 1.0~3.0 1.0~6.0 1.0~3.0 0.0~7.0 0.3~1.0 1.0~4.5 Direct 2.0~7.0 0.3~1.0 1.0~4.5 2.5~7.0 1.0~3.0 3.5~7.0 1.0~3.0 1.0~7.0 0.5~4.5 3.0~7.0 0.3~1.0 v Regular Pattern Group Width(mm) Length(mm)
  • Page 44 Width(mm) Length(mm) Fuctions Presser StitchPattern Foot Auto Manual Auto Manual 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 Satin 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 3.0~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 0.3~1.0 2.5~7.0 1.0~3.0 3.0~7.0 1.0~3.0 3.0~7.0 1.0~3.0...
  • Page 45 Width(mm) Length(mm) Fuctions Presser StitchPattern Foot Auto Manual Auto Manual 3.5~7.0 1.0~3.0 3.0~7.0 1.5~3.0 3.5~7.0 1.5~3.0 2.5~7.0 1.0~3.0 2.5~7.0 1.0~3.0 2.5~7.0 1.0~3.0 2.5~7.0 1.0~3.0 3.0~7.0 1.5~3.0 3.0~7.0 2.0~3.0 2.5~7.0 1.5~3.0 4.0~7.0 2.0~3.0 4.0~7.0 1.0~3.0 3.0~7.0 2.0~3.0 3.0~7.0 1.0~3.0 2.5~7.0 1.0~4.5 2.5~7.0 1.0~3.0 2.5~7.0...

  • Page 46: Alphabet Group-Block Style

    v Alphabet Group-Block style 017 018 026 027 028 029 030 031 032 034 035 040 041 042 049 050 051 052 053 059 060 061 067 068 069 070 071 072 074 075 076 086 087 090 091 092 093 095 096 079 080 081 082 083 084 085 v Alphabet Group-Script style...

  • Page 47: Sewing Basics

    Sewing Basics...

  • Page 48: Straight Stitch

    Straight stitch Using the all purpose foot. Set the stitch as shown in figure. The stitch length can be regulated by pressing the stitch length adjustment button. For a shorter stitch, press the " –" button. For a longer stitch, press the "+" button. Generally speaking, the thicker the fabric, thread and needle, the longer the stitch length should be.

  • Page 49: Zigzag Stitch

    Zigzag stitch Using the all purpose foot or satin stitch foot. Set the stitch as shown in igure. The width can be adjusted between "0.0-7.0" as you press the stitch width adjustment button "+" or "-". Press the stitch length adjustment button "+" or "-"...

  • Page 50: Starting To Sew

    Starting to sew Make sure you follow the needle/fabric/thread combinations and use the suggested presser foot before sewing. 1. Turn the power switch to on ("I"). 2. Press the needle up/down position button to bring the needle to highest position. 3.
  • Page 51 7. Slowly press down the foot control or long press the start/stop button to start sewing. Release the foot control or press the start/ stop button again to stop the machine. Note You can use reverse sewing for back tacking and reinforcing seams by pressing the reverse button.

  • Page 52: Useful Skills

    Useful skills Various ways to achieve better results for your sewing projects are described below. Refer to these tips when sewing your project. The results depend on types of fabrics and stitches. Please use the same fabric of the project and do a sewing test in advance.

  • Page 53: Sewing Corners

    v Sewing corners Stop the sewing machine when you reach a corner. Lower the needle into the fabric. Raise the presser foot lifter. Use the needle as a pivot and turn the fabric 90°. Lower the presser foot lifter and resume sewing.

  • Page 54: Sewing Heavy Fabric

    v Sewing heavy fabric The black button on the right side of the presser foot will lock the presser foot in a horizontal position if you push it in before lowering the presser foot. This ensures even feeding at the beginning of a seam and helps when sewing multiple layers of fabrics such as sewing over seams when hemming jeans.

  • Page 55: Utility Stitches

    Utility Stitches...

  • Page 56: Stretch Stitch

    Stretch stitch Use this stitch with knitted tricot or other stretchy fabrics. The stitch enables your seam to stretch without breaking the thread. Good for easy to ravel and knit fabrics. It’s good for joining durable fabric such as denims. These stitches can also be used as a decorative top stitches.

  • Page 57: Sewing Stretch Fabrics And Elastic Tape

    Sewing stretch fabrics and elastic tape When elastic tape is attached to the cuff or waist of a piece of clothing, the finished dimensions will be that of the stretched elastic tape. Therefore, it is necessary that a suitable length of the elastic tape be used. Using the all purpose foot.

  • Page 58: Overcasting Stitch

    Overcasting stitch Sewing overcasting stitches along the edge of fabric to prevent it from fraying. v Using the all purpose foot 2.0~3.0 2.5~5.0 Attach the all purpose foot. Sewing the overcasting along the edge of the fabric so that the needle drops over the edge of the fabric on the right side.

  • Page 59: Blind Hem

    Blind Hem Secure the bottom of skirts and pants with a blind hem, this stitch will sew with invisible stitch on the right side of the fabric. Using the blind hem foot. 9: Blind hem/lingerie for firm fabrics. 1.0~2.0 2.5~4.0 001: Blind hem for stretch fabrics.

  • Page 60: Buttonhole Stitch

    Buttonhole stitch Buttonholes can be adapted to the size of the button. For stretch fabric or thin fabric, it is recommended to use a stabilizer for a better buttonhole sewing. Slightly reduce upper thread tension to produce better results. Using the electronic buttonhole foot. 0/012: For thin or medium fabric 015/016: For suits or overcoats 010 011...
  • Page 61 The red mark is the standard setting for regular button, adjust the pointer align with the red mark. The buttonhole adjustment button provides a further range of buttonhole size adjustment. (Page 26) ① Regular button The buttonhole length may need to be increased for thick button, adjust the pointer toward to "+"...
  • Page 62 Position the fabric under the presser foot so that the centerline’s mark is aligning with the center of the buttonhole foot. ① Starting point Select the buttonhole stitch. Adjust the stitch width and the stitch length to the desired width and density. Slightly hold the end of the upper thread and start sewing.

  • Page 63: Making A Buttonhole On Stretch Fabrics

    v Making a buttonhole on stretch 018 020 021 fabrics 018: For light to medium weight woven fabrics. 020: For stretch or woven fabric 021: For stretch fabric When sewing buttonholes on stretch fabric, hook heavy thread or cord under the buttonhole foot.

  • Page 64: Bar Tack Stitch

    Bar tack stitch Bar tack stitch is used to reinforce points subject to strain, such as pocket corners and openings. Using the electronic buttonhole foot. Extend the button holder plate and set to the desire length. Adjust the stitch width and the stitch length to the desired width and density.

  • Page 65: Darning Stitch

    Darning stitch Darning a small hole or a tear before it becomes larger can save a garment. Choose a fine thread in a color as color as close to your garment possible. Using the electronic buttonhole foot. Baste the upper fabric and the under fabric together.
  • Page 66 Darning stitches are sewn from the front of the presser foot to the back, as shown. Note If the fabric does not feed, for example, because it is too thick, increase the stitch length. If the sewing range is too big to sew, then we suggest you can sew several times (or cross sew) to get better sewing result.

  • Page 67: Eyelet Stitch

    Eyelet stitch Eyelet stitches are used for making belt holes and other similar applications. Using the satin stitch foot. Press the "+" or "-" stitch width adjustment button to select the eyelet size. ① Small: 5.0mm ② Medium: 6.0mm ③ Large: 7.0mm Lower the needle into the fabric at the beginning of the stitching, and then lower the...

  • Page 68: Button Sewing

    Button sewing Buttons can be sewn on with the sewing machine. Buttons with 2 or 4 holes can be attached. Using the button sewing foot. Move the drop feed lever to lower the feed dogs. ① Lowered position Put the work under the foot and place the button in desired position, then lower the foot.

  • Page 69: Zipper Insertion

    Zipper insertion This foot can be set to sew on each side of the zipper, the edge of the foot guides the zipper to ensure straight placement. Using the zipper foot. 1.5~3.0 n Attention Zipper foot should be used for sewing straight stitches only.

  • Page 70: Inserting A Side Zipper

    Stitching around the zipper. Remove the basting and press. v Inserting a side zipper Place the right sides of the fabric together. Sew a bottom seam 2cm from the right edge of the zipper bottom stop position. Sew few reverse stitches for fixed. Increase the stitch length to maximum, set the tension below 2 and baste the remaining length of the fabric.

  • Page 71: Satin Stitch Sewing

    Turn the fabric right side out. Attach the left pin for sewing the rightside of the zipper. Stitch across the lower end and the right side of the zipper. ① Lower end Stop the machine about 5cm from the top of the zipper.

  • Page 72: Gathering

    Gathering The Gathering Foot is used for gathering fabrics. Ideal for clothing as well as home decor. It works best on thin to medium weight fabrics. Using the gathering foot. v Gathered fabric Remove the presser foot holder and attach the gathering foot, set the tension below 2.

  • Page 73: Smocking

    Smocking The decorative stitch created by stitching or embroidering over gathers is called "smocking". It is used to decorate the front of blouses or cuffs. The smocking stitch adds texture and elasticity to the fabric. Using the satin stitch foot. 004 005 Increase the stitch length to maximum, set the tension below 2 and basting lines 1cm across...

  • Page 74: Free Motion Darning, Embroidery And Monogramming

    Free motion darning, embroidery and monogramming v Preparation for embroidering and monogramming * Embroidery hoop is not included with the 3.5~5.0 machine. Using the darning/embroidery foot. Move the drop feed lever to lower the feed dogs. ① Lowered position Remove the presser foot holder and attach the darning/embroidery foot.

  • Page 75: Darning

    v Darning First sew around the edges of the hole to secure the threads. Working from left to right, sew over the hole in a constant and continuous movement. Turn the work by 1/4 and sew over the first stitching moving the work slower over the hole to separate the threads and not form big gaps between the threads.

  • Page 76: Quilting

    Quilting Sandwich batting between the top and bottom layers of fabric is call "Quilting". The top layer is usually formed by multiple geometrically shaped pieces of materials joined together. Using the Quilting foot with edge/quilting guide. n Attension Only center straight stitches are applicable while using quilting foot.

  • Page 77: Patchwork Stitching

    Using the all purpose foot or satin stitch foot.. 004 005 v Patchwork stitching Place the two fabrics, right sides together and sew using a straight stitch. Open the seam allowance and press it flat. ① Wrong side Working on the right side of the fabric, place the center of the presser foot on the seam line of the joined fabrics and stitch over the seam.

  • Page 78: Applique

    Applique You can create and applique by cutting a different piece of fabric into a shape and using it as a decoration. Using the all purpose foot. 1.0~3.0 3.5~5.0 Cut out the applique design and baste it on the fabric. Sew slowly around the edge of the design.

  • Page 79: Scallop Stitch

    Scallop stitch The wave-shaped repeating stitch, that looks like shells, is called "scalloping". It is used to decorate the collar of blouses and the edges of knitting projects. Using the satin stitch foot or all purpose foot. v Scallop edging Stitch along the edge of the fabric, making sure not to sew directly on the edge of the fabric.

  • Page 80: Cording

    Cording Used for embellishing 1 to 3 cords or decorative threads. Sew over one strand of cording to create a pretty swirled design on a jacket or vest or sew over three strands of cording for border trims. Pearl cotton, knitting yarn, embroidery floss, lace thread, fine wool or lily yarn can be used for cording.

  • Page 81: Narrow Hemming

    Narrow hemming The hemmer foot is used to stitch the narrow rolled hems usually found on shirt tails, table linens and along the edge of frills. Using the hemmer foot. 1.5~3.0 3.0~3.5 Fold edge of fabric over about 3mm, then fold it over again 3mm for about 5cm along the edge of the fabric.

  • Page 82: Walking Foot

    Walking foot Always try to sew first without the walking foot which should be used only when necessary. It is easier to guide the fabric and you have a better view of the seam when using the standard, regular foot on your machine. Your sewing machine offers excellent stitch quality on a wide range of fabrics from delicate chiffons to multiple layers of denim.

  • Page 83: Twin Needle

    Twin needle Using the all purpose foot or satin stitch foot Insert the twin needle. Please refer to "Replacing the needle" chapter for more information. (Page 14) n Attention When using the twin needle, be sure to select the twin needle setting and attach the suggested presser foot which screen appears.
  • Page 84 Two lines of stitching are sewn parallel to each other. Note When sewing with twin needle, always proceed slowly, and make sure to maintain a low speed to insure quality stitching. When twin needle sewing has been selected, it will remain active even the stitch is changed.

  • Page 85: Maintenance And Trouble Shooting

    Maintenance and Trouble shooting...

  • Page 86: Maintenance

    Maintenance n Attention Disconnect the power cord from the wall socket before carrying out any maintenance, otherwise injury or electrical shock may result. v Clean the machine surface If the surface of the sewing machine is dirty, lightly soak a cloth in mild detergent, squeeze it out firmly and then wipe the surface.

  • Page 87: Warning Function

    Warning Function v Warning beeping sound Operate correctly: 1 beep. Operate incorrectly: 2-short beeps. When the sewing machine is in trouble and can't sew: 3-short beeps. It means that the thread may be twisted or jammed and the handwheel axle can't move. Please look through the "Trouble shooting guide"...

  • Page 88: Trouble Shooting Guide

    Trouble shooting guide Before calling for service, check below trouble shooting guides in advance, if problem still exist, please contact nearest dealer or local service center. Problem Cause Correction Reference 1. The machine is not threaded 1. Rethread the upper thread. correctly.
  • Page 89 Problem Cause Correction Reference 1. The machine is not correctly 1. Check the threading and threaded. rethread. 2. The bobbin case is not 2. Thread the bobbin case as Loose threaded correctly. illustrated. stitches 3. Needle/fabric/thread 3. The needle size must suit the combination is wrong.
  • Page 90 Problem Cause Correction Reference 1. The machine is not turned on. 1. Turn on the machine. The sewing machine 2. The presser foot lifter is raised. 2. Lower the presser foot lifter. doesn't 3. The machine is not plugged in. 3. Connect the power cord to the operate electric outlet.
  • Page 92 Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge.

Table of Contents