FireplaceXtrordinair 4237 EG Owner's Manual
Hide thumbs Also See for 4237 EG:

Advertisement

Quick Links

WARNING:
If the information in these instructions is not followed exactly, a fire or explosion may result
causing property damage, personal injury, or loss of life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
A barrier designed to reduce the risk of burns from
the hot viewing glass is provided with this appliance
and shall be installed for the protection of children
and other at-risk individuals.
This appliance may be installed in an aftermarket, permanently located, manufactured home
(USA only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. A conversion
kit is supplied with the appliance.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Travis Industries, Inc.
 Copyright 2021, T.I.
4237 EG
Fireplace
Owner's Manual
HOT GLASS WILL CAUSE
BURNS
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS
12521 Harbour Reach Dr., Mukilteo, WA 98275
$10.00
 Operation
 Maintenance
French language manuals at fireplacex.com
Manuels de langue Française à fireplacex.com
9/16/2021
Listed by
Omni-Test Laboratories, Inc.
Report # 0028GF104S
ANSI Z21.88:19
CSA 2.33:19
CSA 2.17-2017
www.travisproducts.com
100-01562
  

Advertisement

Table of Contents
loading

Summary of Contents for FireplaceXtrordinair 4237 EG

  • Page 1 4237 EG Fireplace Owner’s Manual WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
  • Page 2: Introduction

    Introduction Introduction We welcome you as a new owner of a 4237 EG gas fireplace. This manual details operation and maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your heater and save the manual for future reference.
  • Page 3: Table Of Contents

    Propane Approximate Heating Capacity (in square feet)* Up to 3,000 Up to 3,000 Maximum BTU Input Per Hour 60,000 60,000 Heating capacity will vary with floor plan, insulation, and outside temperature. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 4: Safety Precautions

    © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 5 Young children responsibility of any should be supervised when they consequential damage(s). are in the same room as the heater. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 6: Before You Begin

    "SET" = selected Make sure to keep the on/off button depressed mode enabled. during this process. Release the on/off button to complete "CLR" = selected programming. mode disabled. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 7: Remote Set-Up

    PRG (Program) button for 10 seconds. The pilot will start to spark repeatedly, signifying all system memory has been cleared. The system will return to its original configuration  a remote will need to be synchronized, and the system will operate in Continuous Pilot mode. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 8: Starting The Heater For The First Time

    (i.e.: the IFC “remembers” the last setting). If you wish to adjust the mode settings use the transmitter mode button to adjust the settings. The thermostat and burner on/off operating functions will not work on the transmitter. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 9: Continuous/Intermittent Pilot Switch

    IPI/CPI. NOTE: This icon appears when the appliance is in CPI mode. Press the "UP" button Press the "DOWN" button to activate CPI mode. to activate IPI mode. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 10: Pilot Fuel Conservation Timer

    A programmable thermostat may be set to turn on, once per week, to a high temperature for a short time. This will reset the 7-day timer and allow the heater to operate without having to restart the pilot. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 11: Remote Operation

    NOTE: When the batteries start to get low, the IFC will beep twice whenever a button is pressed. When the batteries are nearly depleted, the IFC will no longer beep. See “IFC Batteries” on page 15). © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 12: Manual On-Off / Smart Thermostat / Standard Thermostat

    NOTE: If the transmitter batteries go dead while in the thermostat setting (standard or smart), the appliance will shut off after approximately 24 hours. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 13: Mode Controls (Flame, Blower, Accent Light, Comfort Control, Aux)

    When in Manual mode the blower will remain on, even if the burner is turned off and the heater cools. Either manually turn the blower off, or turn off the heater by pressing the On/Off button. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 14: Mode Controls (Continued)

    You can adjust the brightness of the light using the built-in rheostat. Use the rheostat on the When in EmberBed fireplace to control the mode (AUX), this EmberBed brightness. icon will appear darkened and the readout will display status. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 15: Display Fahrenheit Or Celsius

    NOTE: When re-installing the battery tray, make sure to secure the battery tray into the battery box using the locking tabs to ensure a good electrical connection. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 16: Battery Installation

    This appliance has several areas that reach high temperatures. Dust or other particles on these areas may burn and create an odor. This is normal during startup. You may notice the smell is more acute if the appliance was left idle for a long period. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 17: Yearly Service Procedure

    After 15 minutes the flames should be orange/yellow and not touch the top of the firebox. If the pilot or  main burners do not burn correctly, contact your dealer for service. Monitor blower operation © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 18: Glass Frame Removal And Installation

    The glass frame tool is shipped inside the fireplace, on the right side of the fireplace opening. The first time it is used you may need to loosen the screw (1/4” wrench). The tool is accessed after removing the screen. NOTE: Replace the tool in this location after use. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 19 (2) tabs on the upper sides of the fireplace opening. Slide the tabs behind the front wall of the fireplace to make room for the removal of the glass assembly. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 20 Remove the glass frame from the fireplace. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 21: Accent Light Replacement

    Tighten the screws until the bulb is secure (do not over-tighten; this may damage the electrical contacts on the bulb).  Return the fireplace to its correct configuration. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 22: Ember-Glo™ Bulb Replacement

    NOTE: Take care to not touch the replacement bulbs with your fingers – use foam packing or paper towel to hold the bulb  Return the fireplace to its correct configuration. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 23: Glass Cleaning

    To clean the inside of the glass, simply remove the glass frame, place it on a non-scratching surface, and clean the surface. WARNING: do not operate the fireplace without the glass frame in place. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 24: Troubleshooting Table

    The accent light fuse may be blown..... Replace the fuse. See fuse location below. Do Not Work Location of fuses The (3) 3 amp fuses are found behind the left side trim (see page 19). © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 25: Wiring Diagram

    Maintenance Wiring Diagram Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 26: Replacement Parts List

    STEPPER MOTOR, LP GS 250-01463 FUSE, 3AMP, 1/4 dia 5-PK 250-03000 BLOWER ASSY LEFT 250-04053 BLOWER ASSY RIGHT 250-04055 CONTROL MODULE 250-03826 Contact your local Travis dealer to purchase replacement parts. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 27: Limited Warranty

    Check with your dealer in advance for any costs to you when arranging a warranty call. Mileage or service charges are not covered by this warranty. This charge can vary from store to store. © Travis Industries 9/16/2021 - 1562 4237 EG Owners...
  • Page 28: Index

    Want to know more? Scan this code with a QR reader on your cell phone or use the URL below to watch a video of how to use the GreenSmart® remote. https://vimeo.com/84052701 © Travis Industries 9/16/2021 - 1562 4237 EG Owners...

This manual is also suitable for:

4237

Table of Contents