Advertisement
periodically run down during normal use
until it stops, then recharge.
9. The charge base may become warm
while charging – this is normal.
MN251RCSC ONLY:
BATTERY REMOVAL
C
ONTAINS
NICKEL
CADMIUM
BATTERY. MUST BE COLLECTED,
R B R C
RECYCLED OR DISPOSED OF
N i - C d
PROPERLY. DO NOT DISPOSE OF IN
THE MUNICIPAL WASTE.
Bring the batteries with the handle of
trimmer to the nearest collection center for
proper disposal. DO NOT throw the battery
into the normal municipal waste system.
OPERATING
INSTRUCTIONS
FOR YOUR MN250RCSC
Battery Version Trimmer
Check to be sure which model
you have purchased.
1. Remove the battery cover by rotating the
bottom cap counter clock wise as below FIG
1, 2, 3 and lifting straight off.
LOCKED
UNLOCKED
Fig. 1
Fig. 2
Fig. 3
2. Being careful not to bend the clips, insert
the positive end of the battery first, so it will
slip easily into position.
3. Return the battery cover to its original
position by pushing it in and rotating clock-
wise until you hear a small click as it locks
into place.
4. To use your trimmer, push ON/OFF switch
upwards to ON position.
5. After you finish using your trimmer, push
down on the ON/OFF switch to turn the trim-
mer off.
6. For your convenience, the trimmer comes
with a storage base to hold the trimmer and
accessories.
*The MN250RCSC requires 1 "AA" battery (not
included). We recommend using alkaline batteries
in your trimmer because they last longer. If you are
not going to use your trimmer for a long period of
time, or if the battery is dead, remove the battery
from the unit. This will increase the life of your trim-
mer.
TYPES OF BEARDS/MUSTACHES
GROWING A BEARD
OR MUSTACHE
There are three key factors that determine
which beard or mustache style is most suit-
able for your face:
1. The shape and dimensions of your face.
2.The natural growth of your beard/
mustache.
3. The thickness of your beard/mustache.
If you are unsure of the type of beard or
mustache that most suits your face, speak
with a professional hair stylist and ask for
an opinion on what style would be best.
Once your beard or mustache has been
styled, it is essential that you maintain its
appearance. To do this, use your shaper to
trim your beard/mustache weekly.
For the best trimming results, your beard
should be slightly damp (not wet) before
using the trimmer. This will prevent
the trimmer from removing more hair
than desired.
GETTING STARTED
TO SWITCH TRIMMER HEADS
Begin with trimmer in locked position (Fig.
1). Hold the handle of the trimmer while
turning the trimmer head counterclockwise
until the triangle on the trimmer head is
Fig. 1
Fig. 2
Fig. 3
aligned with the dash on the side of the han-
dle (Fig. 2). At this point you should be able
to easily lift the trimmer head from the han-
dle (Fig. 3). To replace a trimmer head, align
the triangle on the trimmer head with the
dash on the side of the handle and turn
clockwise until the two triangles are aligned.
OUTLINING YOUR BEARD
1. It is always best to
begin with a clean,
slightly damp beard.
2.
After
you
have
combed through your
beard in the direction it
grows naturally, you will
want to outline the desired shape, beginning
under your jawline.
3. Attach the 3/4" trimmer head. Begin
defining your beard's shape under your chin
and work upward on each side of your face
toward your ears. Then define the upper
outline of your beard across your cheeks,
past your sideburns and toward your hair-
line.
NOW YOU'RE READY
TO TRIM YOUR BEARD
1. To use the 5-position
comb, slide it over the
trimmer blades and snap
down into position. At
first, until you become
familiar with the adjust-
ments, use the longest
comb and trim setting
(5/8"). (You can always
go back and make your
beard a little shorter.)
2. Begin trimming your
beard using smooth,
even strokes. Start with
your sideburns and work downward toward
your chin. (Never attempt to trim against the
natural growth of your beard, because the
Advertisement
