Stiga MP1 500 Li D48 Series Operator's Manual page 72

Traction engaged.
To engage the traction bring the drive ON
lever towards the handle (Fig. 9.B).
Forward speed adjustment is possible
through the selection knob (Fig.10.C).
You can select 6 different levels of speed.
1. Maximum speed (about 5 Km/h).
2. Minimum speed (about 2.5 Km/h).
NOTE The last speed level selected remains
set after the machine is turned off.
IMPORTANT To prevent damage to
the transmission, do not pull the machine
backwards with the drive engaged.
5.5 "ECO" BUTTON
The "ECO" mode allows to save energy when
cutting the grass, optimising the battery life.
Press the button (Fig.10.D) to enable
or disable "ECO" mode.
When the traction is active, the corresponding
LED turns on in the display.
This function automatically switches off when
the operator presence levers are released.
NOTE It is not recommended to use the
"ECO" function in heavy grass cutting conditions
(cutting of dense, high, humid grass).
5.6 CUTTING HEIGHT ADJUSTMENT
Lower or raise the chassis to cut the
grass at different heights.
Carry out this operation when the cutting means
is stationary.
The cutting height is adjusted by using the
designated lever (Fig.11.A) that lifts or lowers
the chassis to the desired position.
6. USING THE MACHINE
The safety regulations to follow are described in
chap. 2. Strictly comply with these instructions to avoid
serious risks or dangers.
6.1 PRELIMINARY PROCEDURES
Before starting work , it is necessary to carry out
several checks and operations to ensure you
can work efficiently and in maximum safety:
Make sure that the safety key is not inserted in its slot.
Place the machine in a stable horizontal
position on the ground.
6.1.1 Checking the battery
Before using the machine for the first time after
purchase, fully charge the battery following
the instructions in the battery booklet.
Before every use of the machine, check the battery charge
status according to the instructions in the battery booklet.
6.1.2 Preparing the machine before starting work
NOTE This machine can be used to mow
lawns in various ways; before starting, prepare the
machine based on how the lawn is to be mowed.
a. Preparation for grass cutting and
collection in the grass catcher:
1. Lift the rear discharge guard (Fig.12.A) and hook
the grass catcher (Fig.12.B) correctly, as indicated
in the figure.
2. For models with side discharge: make sure that
the side discharge guard (Fig.13.B) is lowered.
b. Preparation for grass cutting and rear
grass discharge on the ground:
1. Remove the grass catcher and make sure that the
rear discharge guard (Fig.13.A) is stable in lowered
position.
2. For models with side discharge: make sure that
the side discharge guard (Fig.13.B) is lowered.
c. Preparation for grass mowing and
chopping (mulching function):
1. Lift the rear discharge guard (Fig.14.A) and in-
sert the chute plug (Fig.14.B) in the discharge
opening, keeping it slightly tilted to the right.
2. Fasten it by inserting the two pins
(Fig.14.C) in the specific holes until the
hook claw engages (Fig.14.D).
3. For models with side discharge: make sure that
the side discharge guard (Fig.13.B) is lowered.
To remove the chute plug:
1. Lift the rear discharge guard (Fig.14.A).
2. Press on the centre to release the claw (Fig.14.D).
d. Preparation for grass cutting and
side discharge on the ground:
1. Lift the rear discharge guard (Fig.14.A) and in-
sert the chute plug (Fig.15.B) in the discharge
opening, keeping it slightly tilted to the right.
2. Fasten it by inserting the two pins
(Fig.15.C) in the specific holes until the
hook claw engages (Fig.15.D).
3. Lift the side discharge guard (Fig.15.A).
4. Insert the side discharge chute (Fig.15.E).
Close the side discharge guard (Fig.15.A) so as
5.
to lock the side discharge chute (Fig.15.E).
EN - 6