Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for CNET CWA-854
Summary of Contents for CNET CWA-854
-
Page 1: User Guide
54Mbps Wireless-G Access Point User Guide... -
Page 2: Table Of Contents
1 Introduction ...3 1.1 System Requirements 1.2 Installation Instructions 2 Configuring this Wireless Assess Point 2.1 Setup Wizard ...4 2.1.1 LAN Interface Setup ...5 2.1.2 Wireless Basic Settings ...5 2.1.3 Wireless Security Setup ...6 2.2 Status ...8 2.2.1 System status...9 2.2.2 Wireless Configuration ...9 2.2.3 TCP/IP Configuration status ...10 2.3 Wireless... -
Page 3: Introduction
1 Introduction Congratulations on your purchase of this 54Mbps Wireless-G Access Point. During the design process, we have given much thought to make this device as convenient to use as possible. The end result is the Wireless Access Point that can be set up in minutes, allowing network users to access the Internet via this Wireless Access Point instantly. -
Page 4: Configuring This Wireless Assess Point
2 Configuring this Wireless Assess Point In this chapter, it describes how to use the web management, a web browser-based utility that allows you to remotely configure and manage this Wireless Access Point. This Wireless Access Point’s default IP address is 192.168.1.253, you must set a PC’s IP address in the same domain (e.g. -
Page 5: Lan Interface Setup
This Wireless Access Point has a Setup Wizard to help you easily configure its settings. 2.1.1 LAN Interface Setup The first step in Setup Wizard is LAN interface Setup. Users can change LAN IP address and Subnet Mask here. Most Users will not need to change these values. After typing in the IP Address and Subnet Mask, click “Next”... -
Page 6: Wireless Security Setup
below: 1. Operating band: 802.11B/G, 802.11G or 802.11B. 2. Operating mode: AP, Client, WDS, and AP+WDS. 3. Network type: when operating mode is “Client” mode, users can select the network type as “infrastructure” or “Adhoc”. 4. SSID: The SSID differentiates one WLAN from another, therefore, all wireless access points/routers and all wireless devices attempting to connect to a specific WLAN must use the same SSID. - Page 7 Encryption: WEP WEP: Wired Equivalent Privacy. You may choose either 64-bit or 128-bit as the encryption key and select ASCII or Hex as the format of input value. Encryption: WPA (TKIP), WPA2 (AES) or WPA2 Mixed...
-
Page 8: Status
WPA: Wi-Fi Protected Access. There are three WPA encryption modes - TKIP and AES and Mixed. TKIP: Temporal Key Integrity Protocol AES: Advanced Encryption Standard Mixed: WPA2 Mixed mode operation permits the coexistence of WPA and WPA2 clients on a common SSID. WPA2 Mixed Mode is a Wi-Fi Certified feature. -
Page 9: System Status
This status page provides a brief read-only report for System, Wireless Configuration and TCP/IP Configuration status. The data displayed may be changed depending on your current configuration. 2.2.1 System status This system status includes: Uptime and firmware version. 2.2.2 Wireless Configuration This Wireless Configuration status includes: Mode, Band, SSID, Channel Number, Encryption, BSSID, and Associated Clients. -
Page 10: Tcp/Ip Configuration Status
2.2.3 TCP/IP Configuration status This TCP/IP Configuration status includes: Attain IP Protocol, IP Address, Subnet Mask, Default Gateway, and MAC Address. 2.3 Wireless 2.3.1 Basic Settings The wireless basic settings include Band, Mode, SSID and Channel Number. Disable Wireless LAN Interface: check or uncheck (Enable or Disable). Band: This Wireless Access Point can support three RF band: 802.11B/G, 802.11G and 802.11B. - Page 11 Click “Apply Changes” button when you finish your settings or click “Reset” to undo your changes. In the figure above, click “Show Active Clients” button while there are wireless clients connected to this Wireless Access Point. You will see the figure below to show the MAC address, transmission, reception packet counters and encrypted status for each associated wireless client.
-
Page 12: Advanced Settings
2.3.2 Advanced Settings In Advanced Settings page, more 802.11 related parameters are tunable. Authentication Type: There are three Authentication Type- Open System, Shared Key, and Auto Fragment Threshold: Fragmentation mechanism is used for improving the efficiency when high traffic flows along in the wireless network. If a wireless client often transmits large files in wireless network, you can enter new Fragment Threshold value to split the packet. -
Page 13: Security
802.11b and 802.11g respectively, the packet collision will increase when these two kind devices exist at the same time. We need to enable the Protection mode to increase the performance. 2.3.3 Security Here you can configure the security of your wireless network. Selecting different method will enable you to have different level of security. - Page 14 WEP: Wired Equivalent Privacy. When you press the “Set WEP Key”, you may choose either 64-bit or 128-bit as the encryption key and Select ASCII or Hex as the format of input value. All the four WEP keys are set identical. You can enable the 802.1x Authentication and set the RADIUS server authentication parameters –...
- Page 15 WPA: Wi-Fi Protected Access. There are three encryption modes – TKIP, AES and Mixed. TKIP: Temporal Key Integrity Protocol AES: Advanced Encryption Standard Mixed: WPA2 Mixed mode operation permits the coexistence of WPA and WPA2 clients on a common SSID. WPA2 Mixed Mode is a Wi-Fi Certified feature.
-
Page 17: Access Control
2.3.4 Access control There are three types of access control options: Disable, Allow Listed and Deny Listed. If you choose “Allow Listed”, only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point. When “Deny Listed” is selected, these wireless clients on the list will not be able to connect to the Access Point. -
Page 18: Wds
2.3.5 WDS When you enable the WDS feature selected in the Basic Settings. This Wireless Distribution System (WDS) feature will set this Wireless Access Point in “Bridge Mode”. Two Wireless Access Points in bridge mode can communicate with each other through wireless interface. To do this, you must set these Access Points in the same channel and set MAC address of all other Access Points which you want to communicate with in the table and then enable the WDS. -
Page 19: Site Survey
2.3.6 Site Survey This Wireless Site Survey tool will scan the wireless network. Click “Refresh” button to search for available Access Point or IBSS. If any Access Point or IBSS is found, you may choose to connect it manually when client mode is enabled. 2.4 TCP/IP Settings TCP/IP Settings allows you to configure the parameters for local area network which connects to the LAN port of your Access Point. - Page 20 IP Address: Enter IP address for this Access Point. Subnet Mask: Enter the subnet mask for this Access Point. Default Gateway: Enter Default Gatewayfor this Access Point. DHCP: There are three options for DHCP – Disabled, Client and Server. DHCP Client Range: you can define the IP range for DHCP clients. You can click the “Show Client”...
-
Page 21: Log
2.5 Log You can enable Log data either from wireless or from the whole system. 2.6 Upgrade Firmware This Wireless Access Point allows you to easily upgrade its firmware. -
Page 22: Save/Reload Settings
Select File: click on Browse button to select the firmware and then click on the Upload button. After firmware upgrade is completed, this Wireless Access Point will restart. Note: Do not power off this Wireless Access Point while firmware is being upgraded. 2.7 Save/Reload Settings You can reset this Wireless Access Point back to its default settings by clicking on Reset button, and then press OK button to confirm your decision.