Maintenance; Protecting The Environment - Stanley STHM5 Original Instructions Manual

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
(a), with the other hand on the main handle.
Switching on and off (Fig 1)
1. To run the tool, press the switch (b) and turn it in 'ON'
position.
2. To stop the tool, turn it in 'OFF' position and release the
switch (b).
Chipping and chiselling (Fig 1)
1. Insert the appropriate chisel in right position.
2. Adjust the side handle (a) as required.
3. Switch on the tool and start working.
4. Always switch off the tool when work is finished and
before unplugging.
WARNING:
• Do not use this tool to mix or pump easily combustible or
explosive fluids (benzine, alcohol, etc.).
• Do not mix or stir inflammable liquids labelled accordingly.

MAINTENANCE

Your STANLEY corded/cordless appliance/tool has been
designed to operate over a long period of time with a minimum
of maintenance. To ensure satisfactory operations, the tool
must be maintained and cleaned regularly
WARNING: To reduce the risk of injury, turn
unit off and disconnect machine from power
source before installing and removing
accessories, before adjusting or changing set-ups or
when making repairs. Be sure the trigger switch is in the
OFF position. An accidental start-up can cause injury.
• This machine is not user-serviceable. If problems occur
contact an authorised repair agent.
• The tool will automatically switch off when the carbon
brushes are worn.
• WARNING! Before performing any maintenance on
corded/ cordless power tools:
• Switch off and unplug the appliance/tool.
• Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
• Or run the battery down completely if it is integral and then
switch off.
• Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
• Regularly clean the ventilation slots in your appliance/
tool/ charger using a soft brush or dry cloth.
• Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
• Regularly open the chuck and tap it to remove any dust
from the interior (when fitted).
(Original instructions)
Replace the carbon brush (Fig 4)
• Regularly replace and check the carbon brushes. Replace
it in time when it is worn to the abrasive boundary
line.Keep the carbon brush clean and make it freely slide
in the brushing range. Two brushes shall be replaced at
the same time.
• Use the cross screwdriver to counterclockwise unscrew
the screws (4), open the bottom cover (1) with a flat
screwdriver to counterclockwise open the brush cover (2),
you can remove the brush (3) as shown in the figure 4,
and put the new brush, and then clockwise fasten the
brush cover (2), finally put the bottom cover (1), and then
use the cross screwdriver to tighten it properly.
Lubrication
• Open the cap of the lube oil-injection inlet (e), check the
lube oil in the gearbox, if the lube oil is dirty or insufficient,
replace or add the adequate amount of lube oil provided
by the company.
Cleaning
WARNING! Blow dirt and dust out of the main
housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear
approved eye protection and approved dust mask
when performing this procedure.
WARNING! Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the material of
the parts. Use only mild soap and damp cloth to
clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into liquid.
ACCESSORIES
WARNING! Since accessories, other than those
offered by STANLEY, have not been tested with this
product, use of such accessories with this tool could
be hazardous. To reduce the risk of injury, only STANLEY,
recommended accessories should be used with this product.
Various types of SDS-Max drill bits and chisels are available
as an option. Consult your dealer for further information on the
appropriate accessories.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY product needs
replacement, or if it is of no further use to you, do not dispose
of it with household waste. Make this product available for
separate collection.
ENGLISH
7