Care And Maintenance - Graco ENDURE Owner's Manual

5.
If in doubt, consult either the child restraint manufacturer or
the retailer.

Care and Maintenance

THESE INSTRUCTIONS ARE IMPORTANT. PLEASE READ
CAREFULLY AND RETAIN FOR FUTURE REFERENCE.
It is dangerous to NOT follow the instructions for this product.
Backrest cover removal
First release the elastic strap at the bottom of the backrest cover.
Slide the cover off. The cover can now be cleaned.
Headrest and Seat cushion cover removal
Slide the cover off. The cover can now be cleaned.
Washing the covers
Machine wash cover in cold water on delicate cycle and drip-dry.
DO NOT USE BLEACH.
Assembling your Endure Child Restraint
1 Once removed from the box, place your new Endure on the
floor as shown in 1 .
2 Open the two parts out so that the backrest and seat lie flat,
as shown in 2 .
3 Locate the two hooks at the base of the backrest over the
bars on the back of the seat base (inset).
Raise the backrest to the vertical poistion until it snaps into
place.
9-18 kg
Using the Correct Shoulder Strap Height
Please always read the manual before using it. The manual is
located in the pocket at the side of the seat.
Using the correct shoulder strap height, as shown in 4
Using the Correct Strap Positioning
For infants and toddlers (9kg to 18kg) use middle and bottom
slots and the top loops on the harness strap. -1
5
For older children (up to 18kg) use the top and middle slots and
the bottom loops on the harness strap. 5 -2
9
Changing the Shoulder Strap Height
6 Firstly, loosen the harness.
7 From the rear of the seat find the harness connector.
Release the strap from the harness connector.
From the front of the seat, pull the strap through the slot in
8
the seat's backrest and chest pad.
9 Thread the chest pad through to the back.
10 Thread the chest pad back through the next slot up or
down on the cover and backrest, depending on the size of
your child.
11 Pull the chest pad through to the front of the seat.
12 Make sure that the rubber side of the chest pad faces the
child's chest. Thread the harness strap through the chest
pad. Make sure NOT to twist the straps.
.
13 Re-thread the harness strap back onto the harness
connector at the back of the seat.
Repeat for the other harness strap.
Ensure both straps are at the same height.
Recommended to keep your child harnessed as long as
possible.
Fitting the Child Restraint with the
3-Point Lap & Diagonal Seat Belt
Position the child restraint on the vehicle's seat.
7 -1
-2
7 14 Thread the diagonal of the vehicle seat belt underneath
the headrest as indicated with the red tag, and the lap strap
between the base of the child restraint and the armrest
of the child restraint as indicated with the red tag. Pull the
vehicle seat belt out as much as it will go so there is lots
of slack and feed in through the seat belt route slot in the
seat's plastic backrest furthest from the vehicle's seat belt
buckle as indicated with the red tag.
15 Feed the belt buckle around the back of the child restraint
over the harness straps and back through the opposite seat
belt route slot, to the front of the child restraint.
16 Pull the buckle through the slot and push the child restraint
firmly against the backrest of the vehicle's seat.
17 Feed the buckle and both the diagonal and lap straps
between the armrest and the base of the child restraint as
indicated with the red tag.
18 Fasten the vehicle seat belt into the seat belt buckle making
sure the vehicle seat belt and the buckle are in line with
each other. Please contact the child restraint manufacturer if
in doubt about this point. Finish tightening the vehicle seat
belt until there is no slack and the seat is held firmly in place.
10