Table of Contents
Advertisement
Available languages
Available languages
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as alcohol, petrol or
acetone to clean the appliance.
1
Switch off the appliance and disconnect it from
the wall socket.
2 Wipe the housing of the appliance with a dry
cloth (Fig. 11).
3 Remove the comb and clean it with the
cleaning brush and/or rinse it under the tap
(Fig. 12).
4 Push the teeth of the cutting unit upwards to
remove it from the appliance (Fig. 13).
5 Clean the cutting unit with the cleaning brush
and/or rinse it under the tap (Fig. 14).
6 Clean the inside of the appliance with the brush
and/or rinse it under the tap (Fig. 15).
7 Carefully shake off excess water and let all parts
dry.
8 For optimal performance, lubricate the teeth of
the cutting unit with a drop of sewing machine
oil regularly (Fig. 16).
9 Insert the lug of the cutting unit into the guiding
slot and push the cutting unit back onto the
appliance.
Replacement
Replace damaged parts immediately. Always
replace the cutting unit with the original Philips
cutting unit.
1
Push the teeth of cutting unit upwards and pull
the cutting unit off the appliance (Fig. 13).
2 Remove the used cutting unit.
3 Insert the lug of the new cutting unit into the
guiding slot and push the cutting unit onto the
appliance ('click') (Fig. 17).
Recycling
- Do not throw away the product with the normal
household waste at the end of its life, but hand
it in at an official collection point for recycling.
By doing this, you help to preserve the
environment.
- This product contains a built-in rechargeable
battery which shall not be disposed of with
normal household waste. Please take your
product to an official collection point or a
Philips service center to have a professional
remove the rechargeable battery.
- Follow your country's rules for the separate
collection of electrical and electronic products
and rechargeable batteries. Correct disposal
helps prevent negative consequences for the
environment and human health.
Removing the rechargeable battery
The battery must be removed from the
appliance before it is scrapped.
The appliance must be disconnected from the
supply mains when removing the battery.
The battery is to be disposed of safely.
1
Check if there are screws in the back or front of
the appliance. If so, remove them.
2 Remove the back and/or front panel of the
appliance with a screwdriver. If necessary, also
remove additional screws and/or parts until you
see the printed circuit board with the
rechargeable battery.
3 Remove the rechargeable battery.
Warranty and support
If you need information or support, please visit
www.philips.com/support or read the
international warranty leaflet.
Troubleshooting
This chapter summarizes the most common
problems you could encounter with the product. If
you are unable to solve the problem with the
information below, visit www.philips.com/support
for a list of frequently asked questions or contact
the Consumer Care Center in your country.
Problem
The
appliance
produces an
uneven
cutting
result.
Possible
cause
The comb
does not
touch the
scalp when
you move the
appliance
through the
hair.
You used the
appliance on
wet hair.
You only
move the
appliance in
one direction.
The comb is
not correctly
attached to
the cutting
unit.
The cutting
unit and/or
the comb are
dirty.
The cutting
performance
decreases
when the
battery
runs low.
Solution
Make sure that the
flat part of the
comb is always
fully in contact with
the scalp when you
move the
appliance through
the hair.
Make sure the hair
is clean and dry. Do
not use the
appliance on wet
hair.
Move the
appliance in
different directions
(upward,
downward or
across), because
hair doesn't all
grow in the same
direction.
Remove the comb
and reattach it. Put
the comb into the
slots on both sides
of the appliance
('click').
Clean the cutting
unit and/or the
comb (see
'Cleaning').
Charge the battery
or connect the
appliance to the
wall socket and use
the appliance with
cord.
Advertisement
Table of Contents
