CYBEX VR3 Owner's Manual
Lat pull
Hide thumbs
Also See for VR3:
- Owner's and service manual (46 pages) ,
- Manual (2 pages) ,
- Owner's manual (28 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CYBEX VR3
Summary of Contents for CYBEX VR3
- Page 1 ® Lat Pull Owner's Manual Part Number 12130-999-4 T www.cybexintl.com...
-
Page 2: Table Of Contents
International, Inc. DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. We reserve the right to revise this document at any time or to make changes to the product described within it without notice or obligation to notify any person of such revisions or changes. -
Page 3: Safety Guidelines And Practices
• Fasteners must have a minimum of 500 lbs. tensile capacity. Cybex recommends .3/8” grade 2 bolts or better. A minimum pull force of 220 lbs/100 kgs is required for each anchor position. -
Page 4: User Safety Precautions
• DO NOT pin weights on selectorized equipment in an elevated position or use the machine if found in this position • DO NOT increase weight resistance on equipment by any means other than those provided by Cybex. • DO NOT wear loose or dangling clothing or jewelry while using equipment. Stay clear of moving parts. -
Page 5: Label Placement
VR3 Lat Pull Part Number 12130-999-4 T Caution labels indicate a potentially hazardous situation that could result in serious injury or damage to machine if the precautions are not observed. Contact Cybex Customer Service to replace any worn or damaged labels. - Page 6 VR3 Lat Pull Part Number 12130-999-4 T Page 6 of 21...
-
Page 7: Assembly
VR3 Lat Pull Part Number 12130-999-4 T Assembly Machine Specifications Total Weight and Size VR3 Lat Pull 12130 Standard Stack Weight Machine Dimensions at Rest Machine Dimensions in Use 540 Lbs 59” L × 55” W × 90” H Same 245 Kg 149 cm L ×... -
Page 8: Verify Parts List Below
VR3 Lat Pull Part Number 12130-999-4 T In compliance with the ADA (American Disabilities Act) there must be clear floor space of at least 30 by 48 inches and be served by an accessible route for at least one of each type of exercise equipment. If the clear space is enclosed on three sides (e.g., by walls or the equipment itself), the clear space must... - Page 9 VR3 Lat Pull Part Number 12130-999-4 T If machine CAN be moved without adding or removing weight stack Two people will be required for this procedure 1. Move to desired location. 2. Remove shipping cones using a 3/4" socket or wrench.
- Page 10 • Fasteners must have a minimum of 500 lbs. tensile capacity. Cybex recommends .3/8” grade 2 bolts or better. A minimum pull force of 220 lbs/100 kgs is required for each anchor position.
- Page 11 VR3 Lat Pull Part Number 12130-999-4 T Apply weight plate decal (if not already installed on weight plates) 1. Peel off half of backing from weight plate decals, making sure that the decals remain attached to the front sheet. Description...
- Page 12 VR3 Lat Pull Part Number 12130-999-4 T 4. Verify belt and insert are installed properly. Do not install the insert backwards. Correct belt routing Incorrect belt routing Description Qty. Belt Insert Belt clamp 5. Pull belt tight and secure belt to clamp with set screws.
-
Page 13: Exercise
VR3 Lat Pull Part Number 12130-999-4 T Exercise Intended Use The intended commercial use of this machine is to aid exercise and improve general physical fitness. Instructions Read and understand all instructions and warnings prior to using this machine in the Safety section of the Owner’s Manual. -
Page 14: Maintenance
Do Not inhale or swallow any cleaning product. Protect surrounding area/clothing from exposure. Use in well ventilated area. Follow all product manufacturer’s warnings. Cybex and its vendors cannot be held responsible for damage or injuries resulting from the use or misuse of cleaning products. - Page 15 VR3 Lat Pull Part Number 12130-999-4 T Then 1. Prepare a solution of 10% household bleach (sodium hypochlorite) and 90% water. Dampen a soft white cloth in the solution. 2. Rub gently on the stained area. 3. Dampen a clean soft cloth in water and rinse area.
-
Page 16: Weekly Procedures
VR3 Lat Pull Part Number 12130-999-4 T To Minimize Fine or Hairline Scratches: Mild automotive polish applied and removed with a soft clean cloth will help fill scratches. Suggested Polishes: • Johnson Paste Wax • Mirror Glaze #10 Plastic Polish (by Mirror Bright Polish Co.) •... - Page 17 VR3 Lat Pull Part Number 12130-999-4 T Condition of Belt 3D View 3D or Side View Replace belt if any section is over 1/32” (.03) narrower than the rest of belt Examine edge of belt (both sides). Replace belt if any section is nar- Belt is necked down (narrow sec- rower than the rest.
-
Page 18: Yearly Procedures
VR3 Lat Pull Part Number 12130-999-4 T Yearly Procedures Replace all cables and belts annually Belt Adjustment Tools Required • 7/32" Wrench • Torque wrench 1. Loosen set screws using a 7/32" Allen wrench. Description Set screw Belt 2. Pull belt tight. -
Page 19: Customer Service
Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time. For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239. For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax 508-533-5183. Email address internationaltechhelp@cybexintl.com... -
Page 20: Return Material Authorization (Rma)
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will request a RMA from Cybex, if applicable. Under no circumstances will defective parts or equipment be accepted by Cybex without proper RMA and an Automated Return Service (ARS) label. - Page 21 10 Trotter Drive, Medway, MA 02053 • 888-462-9239 • 508-533-4300 • FAX 508-533-5183 www.cybexintl.com...