Table of Contents
Advertisement
Quick Links
Installation and Operation Manual
Manual P/N 5900387 — Manual Revision B2 — May 2020
Model:
• RFJ-2TX
Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.
⚠
DANGER
2-Ton Long-Reach Floor Jack
Read the
product. Failure to follow the instructions and safety precautions in
this manual can result in serious injury or death. Make sure all other
operators also read this manual. Keep the manual near the product
for future reference. By proceeding with setup and operation,
you agree that you fully understand the contents of this
manual and assume full responsibility for product use.
entire
contents of this manual
1645 Lemonwood Dr.
Santa Paula, CA 93060 USA
Toll Free: (800) 253-2363
Tel: (805) 933-9970
rangerproducts.com
before
using this
Advertisement
Table of Contents
Related Manuals for Ranger RFJ-2TX
Summary of Contents for Ranger RFJ-2TX
- Page 1 2-Ton Long-Reach Floor Jack Installation and Operation Manual Manual P/N 5900387 — Manual Revision B2 — May 2020 Model: • RFJ-2TX Designed and engineered by BendPak Inc. in Southern California, USA. Made in China. ⚠ entire contents of this manual...
- Page 2 Warranty. The BendPak Ranger warranty is more than a commitment to you: it is also a commitment to the value of your new product. For full warranty details, contact your nearest BendPak Ranger dealer or visit bendpak.com/support/warranty.
-
Page 3: Shipping Information
Introduction This manual describes the RFJ-2TX Floor Jack, which safely raises Vehicles up to 2 Tons. More information about the full line of Ranger Products is available at rangerproducts.com. This manual is mandatory reading for all users of the RFJ-2TX, including anyone who sets up, operates, maintains, or repairs it. -
Page 4: Liability Information
BendPak Ranger assumes no liability for damages resulting from: • Use of the equipment for purposes other than those described in this manual. • Modifications to the equipment without prior, written permission from BendPak Ranger. • Damage to the equipment from external influences. •... -
Page 5: Specifications
Specifications Model RFJ-2TX Holding capacity 4,000 lbs. / 1,814 kg Minimum Height 5" / 130 mm Maximum Height 21" / 535 mm Chassis Length 25.75" / 655 mm Front overall width 10" / 255 mm Rear overall width 17" / 433 mm... - Page 6 Setup This section describes how to get your Floor Jack ready for use. To set up your Floor Jack: 1. Remove the Floor Jack from the box. 2. Insert the Handle into the Handle Socket and tighten the Bolt in place. Removing Air Before putting your Floor Jack in operation, remove any trapped air from the Hydraulic System.
-
Page 7: Operation
Operation This section describes how to raise and lower a Vehicle with a Floor Jack. To Raise a Vehicle with a Floor Jack: 1. Drive the Vehicle to the desired location, set the parking brake, put the Vehicle in Park (or in gear, if a manual transmission). -
Page 8: Maintenance
Pump the Handle several times to push oil past the valves under load. in the pump. If you continue to have issues with your Floor Jack, visit https://www.bendpak.com/support/ call BendPak Ranger at (805) 933-9970. 2-Ton Long-Reach Floor Jack P/N 5900387 — Rev. B2 — May 2020... -
Page 9: Parts Breakdown
Parts Breakdown Description Description Rubber Pad Round Pin Saddle Hydraulic Unit Lifting Arm Return Spring Washer 35 Handle Washer 18 Handle Socket Washer for Front Wheel Shaft for Handle Socket Front Wheel Washer 22 Upper Circlip for Piston Nut M12 Dust Ring Flat Washer 12 Bottom Circlip for Piston... -
Page 10: Maintenance Log
Maintenance Log 2-Ton Long-Reach Floor Jack P/N 5900387 — Rev. B2 — May 2020... - Page 11 Maintenance Log 2-Ton Long-Reach Floor Jack P/N 5900387 — Rev. B2 — May 2020...
- Page 12 1645 Lemonwood Drive Santa Paula, CA 93060 USA Copyright © 2020 by BendPak Inc. All rights reserved. bendpak.com...