Rear Panel; Effects Processor; Installation; Mains Voltage - Behringer EUROPOWER PMP2000 User Manual

EUROPOWER PMP2000

2.2 Rear panel

The mains connection is on a standard IEC receptacle. An
appropriate power cord is supplied with the unit.
FUSE HOLDER. Before connecting the unit to the mains,
ensure that the voltage setting matches your local voltage.
Blown fuses should only be replaced by fuses of the same
type and rating.
Use the POWER switch to put your PMP2000 into operation.
The POWER switch should always be in the "Off" position
when you are about to connect your unit to the mains.
Attention: The POWER switch does not fully
disconnect the unit from the mains. Unplug the
power cord completely when the unit is not used
for prolonged periods of time.
This is the RIGHT/MONO MAIN loudspeaker output of
your PMP2000, where you can connect the right
loudspeaker of a stereo system. For this purpose, switch
must be set to its upper position. If, however, you run
a mono main mix (switch
loudspeaker output provides the main mix signal in mono.
The impedance of the loudspeaker connected here
Ω Ω Ω Ω Ω
must not fall below 4
The BRIDGE loudspeaker output allows you to combine
the left and right stereo channel in one mono output, which
is useful for applications that require the use of one
loudspeaker only. To use the BRIDGE output, switch
must be set to "LEFT/RIGHT".
Always connect the BRIDGE jack to a loudspeaker
with a minimum impedance of 8
Please note that the power delivered to the speaker
connected to the BRIDGE output is considerably
higher than the power provided to the speakers
wired to the parallel speaker outputs. Please read
the information given on the rear panel of your
PMP2000.
When using the BRIDGE loudspeaker output, NEVER
use any of the other two connectors (RIGHT/MONO
MAIN and LEFT/MONITOR) at the same time!
This is the LEFT/MONITOR loudspeaker output of your
PMP2000, to which you can connect the left loudspeaker
of a stereo system (switch
If you do a main mix in mono (switch
position), this loudspeaker output provides the monitor signal
in mono.
The impedance of the loudspeaker connected here
Ω Ω Ω Ω Ω
must not fall below 4
Information on how to properly connect your
speaker with regard to polarity can be found on the
rear of the unit (PIN assignment).
SERIAL NUMBER.
6
set to its lower position), this
.
Ω Ω Ω Ω Ω
!
set to its upper position).
set to its lower
.

4. INSTALLATION

3. EFFECTS PROCESSOR

24-BIT MULTI-EFFECTS PROCESSOR
This built-in effects module produces high-grade standard
effects such as reverb, chorus, flanger, delay and various
combination effects. The integrated effects module has the
advantage of requiring no wiring. This way, the danger of creating
ground loops or uneven signal levels is eliminated at the outset,
completely simplifying the handling.
These effect presets are designed to be added to dry signals.
If you move the FX TO MAIN/MON control, you mix the channel
signal (dry) and the effect signal.
Turn down the FX controls in those channel strips
whose signals you don't wish to process.
4. INSTALLATION

4.1 Mains voltage

Before connecting the PMP2000 to the mains, please
carefully check that your equipment is set to the correct
voltage! Blown fuses must be replaced by fuses of the same
type and rating!

4.2 Mains connection

The mains connection is made using the enclosed power cord
and a standard IEC receptacle. It meets all of the international
safety certification requirements.
Please make sure that all units have a proper
ground connection. For your own safety, never
remove or disable the ground conductor from the
unit or of the AC power cord.

4.3 Audio connections

The in and outputs of your BEHRINGER PMP2000 are de-
signed as unbalanced 1/4" mono jacks—except for the mono
channel line inputs, which come as balanced 1/4" stereo jacks. Of
course, all in and outputs work with both balanced and unbalanced
connectors. The tape ins and outs are on stereo RCA connectors.
Please ensure that only qualified personnel install
and operate the PMP2000. During installation and
operation, the user must have sufficient electrical
contact to earth. Electrostatic charges might affect
the operation of the unit.
Fig. 4.1: 1/4" mono plug