Operation; Console Setup; Selection Lists On Screen; Using Stereo Channels - Behringer DIGITAL PRO MIXER DDM4000 User Manual

3.

Operation

3.1

Console Setup

Console Setup allows you to make all standard settings for the
DDM4000.
1) Press the CONSOLE SETUP knob
seconds. The setup list appears in the center of the display.:
2) Turn the CONSOLE SETUP knob to select the setup you
want to edit.
3) Press the CONSOLE SETUP knob to confirm the selection.
Exit Console Setup:
Press the ESC push button
=
Some of the setup pages can be accessed in different ways. This
is the case for Mic Setup and User Settings:
Open Mic Setup:
1) Press the MIC SETUP push button
Setup.
2) Press the MIC SETUP push button
Setup.
Open User Settings:
1) Press the LOAD push button
2) Press the LOAD push button
tings.
3.1.1

Selection lists on screen

The individual setup pages contain further selection lists, which
appear either on the left or right side of the display, in addition to
the Console Setup list.
Left:
1) Turn the left PARAMETER knob
select the preferred function from the list.
2) Press the left PARAMETER knob to confirm the selection.
Right:
1) Turn the right PARAMETER knob
select the preferred function from the list.
2) Press the right PARAMETER knob to confirm the selection.
[51] for approximately 2
[52] to exit Console Setup.
[16] to access Mic
[16] again to exit Mic
[35] to access User Settings.
[35] again to exit User Set-
[45] (in the FX1 section) to
[45] (in the FX2 section) to
Operation
DIGITAL PRO MIXER DDM4000
3.2

Using stereo channels

3.2.1

EQ modes: SINGLE and MULTI

The equalizer provides Preset push buttons, labeled P1, P2 and
P3, with which preset configurations are stored. The behavior
of the push buttons depend on the selected EQ mode: Single
Mode or Multi Mode. After switching on the device, Single Mode
is active.
SINGLE Mode:
In Single Mode, the push buttons P1, P2 and P3 {6} are each
permanently assigned to a frequency band (P1 = HIGH, P2 = MID,
P3 = LOW). This means that a Preset can be assigned to each
EQ control. When activated, the Preset push buttons provide a
Kill function with maximum attenuation (-? dB).
Preset settings in SINGLE Mode
P1 Suppresses high frequencies
HIGH Kill -? dB
P2 Suppresses mid frequencies
MID Kill -? dB
P3 Suppresses low frequencies
LOW Kill -? dB
Tab. 3.1: Functionality of Preset push buttons in Single Mode
The degree of cut can, however, be modified. Alternatively, a fre-
quency boost can also be stored. In case you want to boost instead
of cutting the bass (Punch function), proceed as follows:
1) Turn the LOW knob {4} to the right until you have reached
the boost you want.
2) Press and hold the MODE push button
P3 {6}.
3) Press P3 to load the Preset. The bass frequencies are now
boosted. P3 flashes blue.
This way you can also program the mids and highs with P2 and
P1 respectively.
Reset:
The Preset push buttons can be restored to their initial states at
all times (Reset function):
= Press MODE {5} for approximately 2 seconds. The MULTI
LED briefly lights up to confirm the reset.
MULTI Mode:
In Multi Mode, the Preset push buttons are not assigned to in-
dividual EQ bands, but are assigned to the 3-band equalizer as
a whole. This way you can create three EQ presets and assign
these to the Preset push buttons. When activated, the Preset push
buttons are assigned as follows:
Preset settings in MULTI Mode
P1 High pass Suppresses MID and LOW
P2 Band pass Suppresses HIGH and LOW
P3 Low pass Suppresses HIGH and MID
Tab. 3.2: Functionality of Preset push buttons in Multi Mode
To activate Multi Mode, press the MODE push button
=
The MULTI LED lights up.
To create your own EQ presets, proceed as follows:
1) Adjust the equalizer as needed by turning the LOW, MID and
HIGH knobs.
2) Press and hold the MODE push button
P1 {6}.
3) Press P1 to load the EQ Preset. P1 flashes yellow.
Two more EQ Presets can be stored with P2 and P3.
Reset:
The Preset push buttons can be restored at all times:
Press MODE for approximately 2 seconds. The SINGLE LED
=
briefly lights up to confirm the reset.
{5} while pressing
{5}.
{5} while pressing
13