Initial Operation; Shipment; Online Registration - Behringer PRO MIXER DJX750 User Manual

7
PRO MIXER DJX750 User Manual
(42) The DJX750 features an integrated effects loop for the connection of an
external effects device. The MONITOR signal is taken at the SEND output
and routed, for example, to a reverb processor. Thus, the signal at the SEND
connector is identical to the headphones signal and is selected with the
MONITOR CUE buttons (16) .
(43) The externally processed signal is added to the MASTER output signal via the
RETURN connectors. The effect signal volume may only be adjusted at the
output control of the effects device itself.
(44) The MASTER output is for connecting to an amplifier and can be adjusted
with the MASTER fader (18) .
◊
Always turn the power amps on last to avoid inrush currents that can
easily damage your speakers. And, to avoid sudden and unpleasant
surprises for your ears, make sure there is no signal at the DJX750
before turning on the power amps. To be sure, slide all the faders to the
bottom and switch all controls to the zero position.
(45) The BOOTH output gives you an additional option of connecting an amplifier
in order to, for example, feed the signal into your monitors or to bring sound
to an extra area. The BOOTH output level is regulated by using the BOOTH
LEVEL control (20) of the MASTER section.
(46) Using the TAPE output you can record your music by connecting devices such as
tape decks, DAT recorders etc. Unlike the MASTER output, the output volume is
fixed, making it necessary for you to adjust the input level on the recording device.
(47) The POWER switch powers the DJX750 on. You should always make sure that
the POWER switch is in the "Off" position when initially connecting the unit
to the mains.
◊
Merely switching the unit off does not mean that it is fully disconnected
from the mains. When not using the unit for prolonged periods of time,
please unplug the unit's power cord from the power outlet.
(48) This is the connector for the power cable. This is where the advantage of a
sophisticated internal power supply can be seen: the pulse behaviour of each
amplifying circuit is mainly determined by the voltage reserves available.
Each mixing console is equipped with numerous operational amplifiers
(op amps) to process line level signals. Due to limited output of their power
supplies, many mixing consoles show signs of "stress" when subjected to
heavy loads. But not your DJX750: the sound is always clear and transparent.
(49) FUSE HOLDER / VOLTAGE SETTING. Before connecting the unit to the mains,
ensure that the voltage setting matches your local voltage. Blown fuses
should only be replaced by a fuse of the same type and rating. On some
units, the fuses holder can be switched to one of two positions, i.e. 230 V and
120 V. Please note: should you desire to operate the unit outside Europe at
120 V, a higher fuse rating is required.
◊
To disconnect power from main, pull out the main cord plug.
When installing the product, ensure that the plug is easily accessible.
If mounting in a rack, ensure that the mains can be easily disconnected
by a plug or by an all-pole disconnect switch on or near the rack.
(50) SERIAL NUMBER.

3. Initial Operation

◊
Ensure adequate air supply and to avoid overheating do not place the
unit near radiators etc.
◊
Before you connect your unit to the mains, please make sure that your
local voltage matches the voltage required by the unit. The fuse holder
on the mains connector has 3 triangular markings, with two of these
triangles opposing each other. The unit is set to the operating voltage
printed next to these markers and can be set to another voltage by
turning the fuse holder by 180°.
! !
Caution
Please note that when operating the unit at 120 V, a higher fuse rating is
required. Please refer to the "Specifications" for details.
If you set the unit to a different mains voltage, be sure to use a fuse of the correct
type and rating. Please refer to the "Specifications" for details.
◊
Blown fuses must be replaced by fuses of the correct rating!
Please refer to the "Specifications" section for the applicable rating.
Before you change the fuse, switch off the device and pull the plug to
avoid electric shock or damage to the device.
The mains connection is made using the enclosed power cord and a standard IEC
receptacle. It meets all international safety certification requirements.
◊
Please make sure that all devices are properly grounded. For your own
safety, never remove or disable the ground conductors from the devices
or on the power cords. The unit must always be connected to the mains
outlet with a protective grounding connection.
◊
The sound quality may diminish within the range of powerful
broadcasting stations and high-frequency sources. Increase the
distance between the transmitter and the device and use shielded
cables for all connections.

4. Shipment

Should your BEHRINGER product malfunction, it is our intention to have it
repaired as quickly as possible. To arrange for warranty service, please contact
the BEHRINGER retailer from whom the equipment was purchased. Should your
BEHRINGER dealer not be located in your vicinity, you may directly contact one of
our subsidiaries.
Corresponding contact information is included in the original equipment
packaging (Global Contact Information/European Contact Information).
Should your country not be listed, please contact the distributor nearest
you. A list of distributors can be found in the support area of our website
(behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims more quickly and efficiently.
Your product was carefully packed at the factory to ensure safe transport.
Nevertheless, if the box is damaged inspect the unit immediately for signs
of damage.
◊
If the unit is damaged please do NOT return it to us, but notify your
dealer and the shipping company immediately; otherwise, claims for
damage or replacement may not be granted.
◊
Always use the original box to prevent damage during storage
or transport.
◊
Make sure that children cannot play unsupervised with the unit or
its packaging.

5. Online Registration

Please register your new BEHRINGER equipment right after your purchase
by visiting behringer.com and read the terms and conditions of our
warranty carefully.
Thank you for your cooperation!