Routine Maintenance; Special Maintenance; In Case Of Difficulty - Jacuzzi flexa DOUBLE Use & Maintenance

Routine maintenance

I With models equipped with a waterfall function, up-
on termination of this function, ensure that you drain
all the water in the tray/tub, and then thoroughly clean
the aforementioned.
I The flexible showerhead is provided with a filter that could
become clogged due to impurities and/or lime scale; this fil-
ter can be cleaned by unscrewing the showerhead from its
flexible hose.
I If there is lime scale build-up on the nozzles which changes
the form of the massaging jet, we suggest removing and clean-
ing the outer ring nut as follows:
- turn the ring nut all the way counter-clockwise as far as
it will go (you will hear a slight click). Then extract the ring
nut and thoroughly clean the centre hole.
- do not use metallic tools (scissors, screwdrivers, etc.).
Rather, let the ring nut soak in a slightly acetic solution
(liquid scale remover).
- When you put the ring nut back in place, make sure it
hooks firmly onto the tooth of the nozzle.
I For normal cleaning of FLEXA (walls, corner element, top,
accessories in general), do not use abrasive detergents, alco-
hol, or other solvents/thinners. Use only neutral liquids.
I If you want to wash/clean the essential oils dispenser, pro-
ceed as follows:
- detach the cover of the steam outlet by squeezing the plas-
tic tabs with two fingers and pulling gently.
- push up on the tab at the bottom of the container, so as
to detach the cover-container assembly from the outlet.
- once washed with neutral detergent, replace it on the steam
outlet.
I Glass surfaces can be cleaned with normal, commercially
available products for this purpose.
I The glass panels of some models are protected by "Crys-
tal Clear", a special treatment that reduces the build-up of
scale and the formation of stains caused by humidity and show-
er products, leaving the glass panel easier to clean.
"Crystal Clear" treatment reduces maintenance time and
costs, keeping the shower glass panels clean and bright over
time (this, however, depends on the degree of water hardness
and how often the shower enclosure is used).
Maintenance is very simple: after using the shower en-
closure, rinse the glass panels with water, and if necessary dry
them with a cloth. Do not use abrasive pads and/or creamy or
powdered detergents.
Occasionally, when just rinsing does not leave it as clean
and bright as you would like, the glass panels can be cleaned
with special scale-remover detergents.
After a period of time, if you should notice that water does
not run off the glass panel so well, you can apply special prod-
ucts that can aid this. Refer to an Authorized Jacuzzi
Centre, however, for this type of maintenance.
Never use abrasive cloths, powder detergents, acetone
or other solvents.

Special maintenance

I Any unscheduled maintenance work, for example on the
electromechanical parts on the back of the fitted-out wall, or
scratches and stains on acrylic parts, are to be handled exclu-
sively by specialized personnel.
In such cases, contact only an Authorized Jacuzzi
tre.
In the event of difficulty...
I SYMPTOM
Solution
I NO WATER IS SUPPLIED FROM FUNCTIONS (SHOW-
ER, CASCADE, HYDROMASSAGE, ETC.)
Turn on the mixer tap.
I DISPLAY OFF.
Place the main switch in the ON position (see installation
manual).
I THE SHOWER PROVIDES INADEQUATE PRESSURE.
Clean the shower filter.
I LITTLE WATER IS DISPENSED IN ALL FUNCTIONS.
Check that the installer has complied with the pressure/flow
rate conditions set forth on the installation manual. For wa-
ter that is hard or contains a lot of impurities, or after inten-
sive use of the shower box, you may need to have the filters
of the solenoid valves cleaned (call technical service). If the
shower box is equipped with a thermostatic mixer, its filter
may be clogged with dirt and/or lime scale.
I THE HYDROMASSAGE PROVIDES INADEQUATE
PRESSURE.
Clean the nozzles. If this does not suffice, call technical serv-
ice (for cleaning of solenoid valve filter and/or verification of
mains pressure/flow rate).
I DIFFICULT TO ADJUST THE WATER TEMPERATURE
(MIXING)
Check that the pressure values of the system (operating) for
Service
®
hot and cold water are well-balanced. If the values are dif-
ferent, it is advisable to contact your entrusted plumber.
49
® Service Cen-