Summary of Contents for AudioCodes MediaPack MP-1 Series
Page 1
SIP Phone Support (SPS) MediaPack™ MP-1xx SIP Protocol Configuration Note Setting up FXS Lines on MP-1xx for SIP Phone Support February 2013 Document # LTRT-31325 Version 1.0...
Configuration Note Contents Table of Contents Overview ......................7 Setting Up FXS Lines on MP-1xx ............... 9 Configuring the SPS as a Proxy ................9 Defining the Gateway Name ................. 10 Enabling the G.711 Codec..................11 Assigning User Name to FXS Port ................ 12 Configuring the Hunt Group ..................
Page 4
Setting Up FXS Lines on MP-1xx for SPS List of Figures Figure 2-1: Proxy Sets Table ........................9 Figure 2-2: Proxy & Registration ......................10 Figure 2-3: Coders Table ........................11 Figure 2-4: Endpoint Phone Number Table ....................12 Figure 2-5: Hunt Group Settings ......................13 Figure 2-6: IP to Hunt Group Routing Table ...................14 Figure 2-7: Authentication ........................15 Figure 2-8: Endpoint Phone Number Table ....................16...
Page 5
Configuration Note Notices Notice This document describes the procedures for setting up FXS lines using AudioCodes MP-1xx for AudioCodes SPS (SIP Phone Support) Information contained in this document is believed to be accurate and reliable at the time of printing. However, due to ongoing product improvements and revisions, AudioCodes cannot guarantee the accuracy of printed material after the Date Published nor can it accept responsibility for errors or omissions.
Page 6
Setting Up FXS Lines on MP-1xx for SPS Related Documentation Manual Name MP-11x Installation Manual MP-11x User’s Manual SPS for Lync Quick Start Guide Configuration Note Document#: LTRT-31325...
Configuration Note 1. Overview Overview This document describes the procedures for setting up FXS lines using AudioCodes MP- 1xx for AudioCodes SPS (SIP Phone Support). Version 3.0 February 2013...
Page 8
Setting Up FXS Lines on MP-1xx for SPS Reader's Notes Configuration Note Document#: LTRT-31325...
Configuration Note 2. Setting Up FXS Lines on MP-1xx Setting Up FXS Lines on MP-1xx Before setting up the FXS lines, you need to create an SPS user in the SPS Web Admin Tool. Follow the instructions on how to create a new SPS user in the “Adding a User via the SPS Web Admin”...
Setting Up FXS Lines on MP-1xx for SPS Defining the Gateway Name The procedure below describes how to define the gateway name. To define the gateway name: Click Configuration > VoIP > SIP Definitions > Proxy & Registration; the Proxy & Registration page opens.
Configuration Note 2. Setting Up FXS Lines on MP-1xx Enabling the G.711 Codec The procedure below describes how to enable the G.711 codec. To enable the G.711 codec: Click Configuration > VoIP > Coders and Profiles > Coders; the Coders Table page opens: Figure 2-3: Coders Table On the first line, from the 'Coder name' drop-down list, select G.711U-law.
Setting Up FXS Lines on MP-1xx for SPS Assigning User Name to FXS Port The procedure below describes how to assign a User Name to the FXS Port. To assign user name to FXS port: Click Configuration > VoIP > GW and IP to IP > Hunt Group > Endpoint Phone Number;...
Configuration Note 2. Setting Up FXS Lines on MP-1xx Configuring the Hunt Group The procedure below describes how to configure the Hunt Group. To configure the Hunt Group: Click Configuration > VoIP > GW and IP to IP > Hunt Group > Hunt Group Settings;...
Setting Up FXS Lines on MP-1xx for SPS Configuring IP to Hunt Group Routing The procedure below describes how to configure IP to Hunt Group Routing. To configure IP to Hunt group routing: Click Configuration > VoIP > GW and IP to IP > Routing > IP to Trunk Group Routing;...
Configuration Note 2. Setting Up FXS Lines on MP-1xx Configuring Port Authentication The procedure below describes how to configure Port Authentication. To set port authentication: Click Configuration > VoIP > GW and IP to IP > Analog Gateway > Authentication;...
Setting Up FXS Lines on MP-1xx for SPS Registering the FXS Port The procedure below describes how to register the FXS port. To register the user name to FXS port: Click Configuration > VoIP > GW and IP to IP > Hunt Group > Endpoint Phone Number;...
Configuration Note 2. Setting Up FXS Lines on MP-1xx Verifying FXS Port Registration in the SPS The procedure below describes how to verify FXS port registration in the SPS. To verify FXS port registration in the SPS: In the SPS Web Admin, click Status & Diagnostics > System Status > Phones Status;...