Page 1 User's Manual Version 5.4 Document #: LTRT-65410 May 2008...
Page 3: Table Of Contents
SIP User's Manual Contents Table of Contents Overview ......................15 Gateway Description ....................15 MediaPack Features ....................17 1.2.1 MP-11x Hardware Features ..................17 1.2.2 MP-124 Hardware Features ..................17 SIP Overview ......................18 Configuration Concepts ...................19 Web-Based Management..................21 Computer Requirements ..................21 Accessing the Web Interface .................
Page 4 MediaPack Series 3.4.2 Media Settings ......................67 3.4.2.1 Configuring the Voice Settings..............67 3.4.2.2 Configuring the Fax / Modem / CID Settings .......... 70 3.4.2.3 Configuring the RTP / RTCP Settings............. 74 3.4.2.4 Configuring the General Media Settings ..........77 3.4.2.5 Configuring the Hook-Flash Settings ............
Page 5 SIP User's Manual Contents Modifying an ini File ..................... 231 Reference for ini File Parameters ................ 232 4.4.1 Networking Parameters ..................232 4.4.2 System Parameters ....................240 4.4.3 Web and Telnet Parameters................. 246 4.4.4 Security Parameters ..................... 248 4.4.5 RADIUS Parameters..................... 255 4.4.6 SNMP Parameters....................
Page 6 MediaPack Series 7.3.2.3 Ring Detection Timeout................. 327 7.3.2.4 FXO Supplementary Services............... 328 Event Notification using X-Detect Header............328 RTP Multiplexing (ThroughPacket) ..............330 Dynamic Jitter Buffer Operation ................330 Configuring Alternative Routing (Based on Connectivity and QoS) ..... 331 7.7.1 Alternative Routing Mechanism................
Page 7 SIP User's Manual Contents VLANS and Multiple IPs..................366 8.8.1 Multiple IPs ......................366 8.8.2 IEEE 802.1p/Q (VLANs and Priority)..............367 8.8.3 Getting Started with VLANS and Multiple IPs ............370 8.8.3.1 Integrating Using the Web Interface............370 8.8.3.2 Integrating Using the ini File..............373 Supplied SIP Software Package..............375 10 Selected Technical Specifications..............377 10.1 MP-11x Specifications..................
Page 8 MediaPack Series List of Figures Figure 1-1: Typical MediaPack VoIP Application ...................16 Figure 3-1: Enter Network Password Screen ..................22 Figure 3-2: Main Areas of the Web Interface GUI..................23 Figure 3-3: "Reset" Displayed on Toolbar ....................24 Figure 3-4: Terminology for Navigation Tree Levels ................25 Figure 3-5: Navigation Tree in Basic and Full View ................26 Figure 3-6: Showing and Hiding Navigation Pane .................27 Figure 3-7: Toggling between Basic and Advanced Page View ............29...
Page 9 SIP User's Manual Contents Figure 3-57: Proxy Sets Table Page ....................117 Figure 3-58: Coders Page ........................122 Figure 3-59: DTMF & Dialing Page ..................... 123 Figure 3-60: Advanced Parameters Page ................... 127 Figure 3-61: Supplementary Services Page..................135 Figure 3-62: Metering Tones Page...................... 140 Figure 3-63: Charge Codes Table Page .....................
Page 10 MediaPack Series Figure 7-1: Call Flow for One-Stage Dialing..................323 Figure 7-2: Call Flow for Two-Stage Dialing..................324 Figure 7-3: Call Flow for Automatic Dialing ..................326 Figure 7-4: Call Flow for Collecting Digits Mode ................. 327 Figure 7-5: SIP Call Flow........................338 Figure 7-6: Assigning Phone Numbers to Device 10.2.37.10 .............
Page 11 SIP User's Manual Contents List of Tables Table 1-1: Supported MediaPack Series Configurations ...............15 Table 3-1: Description of Toolbar Buttons....................24 Table 3-2: ini File Parameters for Changing Logo Image ..............45 Table 3-3: ini File Parameters for Replacing Logo with Text ..............45 Table 3-4: ini File Parameters for Customizing Product Name ..............46 Table 3-5: ini File Parameter for Welcome Login Message ..............46 Table 3-6: Description of the Areas of the Home Page................48...
Page 12 MediaPack Series Table 3-57: Call Counters Description ....................221 Table 3-58: Call Routing Status Parameters..................222 Table 3-59: SAS Registered Users Parameters ................. 224 Table 3-60: IP Connectivity Parameters....................225 Table 4-1: Networking Parameters...................... 232 Table 4-2: System Parameters......................240 Table 4-3: Web and Telnet Parameters ....................
Page 13: Weee Eu Directive
SIP User's Manual Notices Notice This document describes the AudioCodes MediaPack series Voice over IP (VoIP) SIP media gateways. Information contained in this document is believed to be accurate and reliable at the time of printing. However, due to ongoing product improvements and revisions, AudioCodes cannot guarantee accuracy of printed material after the Date Published nor can it accept responsibility for errors or omissions.
Page 14: Related Documentation
MediaPack Series Related Documentation Document # Manual Name LTRT-523xx (where xx is the Product Reference Manual document version) LTRT-656xx MP-11x and MP-124 SIP Release Notes LTRT-598xx MP-11x and MP-124 SIP Installation Manual LTRT-665xx CPE Configuration Guide for IP Voice Mail Warning: The device is supplied as a sealed unit and must only be serviced by qualified service personnel.
Page 15: Overview
SIP User's Manual 1. Overview Overview This manual provides you with information for configuring and operating the VoIP analog MediaPack series devices listed in the table below: Table 1-1: Supported MediaPack Series Configurations Combined FXS / Number of Product Name Channels MP-124 MP-118...
Page 16: Figure 1-1: Typical Mediapack Voip Application
MediaPack Series The figure below illustrates a typical MediaPack VoIP application. Figure 1-1: Typical MediaPack VoIP Application SIP User's Manual Document #: LTRT-65410...
Page 17: Mediapack Features
SIP User's Manual 1. Overview MediaPack Features This section provides a high-level overview of some of the many device supported features. For more updated information on the device's supported features, refer to the latest MP-11x & MP-124 SIP Release Notes. 1.2.1 MP-11x Hardware Features The MP-11x series hardware features include the following:...
Page 18: Sip Overview
MediaPack Series SIP Overview Session Initiation Protocol (SIP) is an application-layer control (signaling) protocol used on the gateway for creating, modifying, and terminating sessions with one or more participants. These sessions can include Internet telephone calls, media announcements, and conferences. SIP invitations are used to create sessions and carry session descriptions that enable participants to agree on a set of compatible media types.
Page 19: Configuration Concepts
Note: To initialize the device by assigning it an IP address, a firmware file (cmp), and a configuration file (ini file), you can use AudioCodes' BootP/TFTP utility, which accesses the device using its MAC address (refer to the Product Reference Manual).
Page 20 MediaPack Series Reader's Notes SIP User's Manual Document #: LTRT-65410...
Page 21: Web-Based Management
SIP User's Manual 3. Web-Based Management Web-Based Management The device's Embedded Web Server (Web interface) provides FCAPS (fault management, configuration, accounting, performance, and security) functionality. The Web interface allows you to remotely configure your device for quick-and-easy deployment, including uploading of configuration (software upgrade) and auxiliary files, and resetting the device. The Web interface provides real-time, online monitoring of the device, including display of alarms and their severity.
Page 22: Accessing The Web Interface
MediaPack Series Accessing the Web Interface The Web interface can be opened using any standard Web browser (refer to ''Computer Requirements'' on page 21). When initially accessing the Web interface, use the default user name ('Admin') and password ('Admin'). For changing the login user name and password, refer to ''Configuring the Web User Accounts'' on page 79).
Page 23: Getting Acquainted With The Web Interface
SIP User's Manual 3. Web-Based Management Getting Acquainted with the Web Interface The figure below displays the general layout of the Graphical User Interface (GUI) of the Web interface: Figure 3-2: Main Areas of the Web Interface GUI The Web GUI is composed of the following main areas: Title bar: Displays the corporate logo and product name.
Page 24: Toolbar
MediaPack Series 3.3.1 Toolbar The toolbar provides command buttons for quick-and-easy access to frequently required commands, as described in the table below: Table 3-1: Description of Toolbar Buttons Icon Button Name Description Submit Applies parameter settings to the device (refer to ''Saving Configuration'' on page 207).
Page 25: Navigation Tree
SIP User's Manual 3. Web-Based Management 3.3.2 Navigation Tree The Navigation tree, located in the Navigation pane, displays the menus (pertaining to the menu tab selected on the Navigation bar) used for accessing the configuration pages. The Navigation tree displays a tree-like structure of menus. You can easily drill-down to the required page item level to open its corresponding page in the Work pane.
Page 26: Displaying Navigation Tree In Basic And Full View
MediaPack Series To navigate to a page, take these 2 steps: Navigate to the required page item, by performing the following: • Drilling-down using the plus signs to expand the menus and submenus • Drilling-up using the minus signs to collapse the menus and submenus Select the required page item;...
Page 27: Showing / Hiding The Navigation Pane
SIP User's Manual 3. Web-Based Management 3.3.2.2 Showing / Hiding the Navigation Pane The Navigation pane can be hidden to provide more space for elements displayed in the Work pane. This is especially useful when the Work pane displays a page with a table that's wider than the Work pane and to view the all the columns, you need to use scroll bars.
Page 28: Accessing Pages
MediaPack Series 3.3.3.1 Accessing Pages The configuration pages are accessed by clicking the required page item in the Navigation tree. To open a configuration page in the Work pane, take these 2 steps: On the Navigation bar, click the required tab: •...
Page 29: Figure 3-7: Toggling Between Basic And Advanced Page View
SIP User's Manual 3. Web-Based Management 3.3.3.2.1 Displaying Basic and Advanced Parameters Some pages provide you with an Advanced Parameter List / Basic Parameter List toggle button that allows you to show or hide advanced parameters (in addition to displaying the basic parameters). This button is located on the top-right corner of the page and has two states: Advanced Parameter List button with down-pointing arrow: click this button to display all parameters.
Page 30: Modifying And Saving Parameters
MediaPack Series 3.3.3.2.2 Showing / Hiding Parameter Groups Some pages provide groups of parameters, which can be hidden or shown. To toggle between hiding and showing a group, simply click the group name button that appears above each group. The button appears with a down-pointing or up-pointing arrow, indicating that it can be collapsed or expanded when clicked, respectively.
Page 31: Figure 3-9: Editing Symbol After Modifying Parameter Value
SIP User's Manual 3. Web-Based Management Figure 3-9: Editing Symbol after Modifying Parameter Value To save configuration changes on a page to the device's volatile memory (RAM), take this step: Click the Submit button, which is located near the bottom of the page in which you are working;...
Page 32: Entering Phone Numbers In Various Tables
MediaPack Series 3.3.3.4 Entering Phone Numbers in Various Tables Phone numbers or prefixes that you enter in various tables throughout the Web interface such as the 'Tel to IP Routing' table, must only be entered as digits without any other characters.
Page 33: Figure 3-12: Compacting A Web Interface Table
SIP User's Manual 3. Web-Based Management Click Duplicate; a new index entry is added with identical settings as the selected index in Step 1. In addition, all existing index entries are incremented by one and the newly added index entry is assigned the index 0. To edit an existing index table entry, take these 3 steps: In the 'Index' column, select the index corresponding to the table row that you want to edit.
Page 34: Searching For Configuration Parameters
MediaPack Series 3.3.4 Searching for Configuration Parameters The Web interface provides a search engine that allows you to search any ini file parameter that is configurable by the Web interface (i.e., has a corresponding Web parameter). You can search for a specific parameter (e.g., "EnableIPSec") or a sub-string of that parameter (e.g., "sec").
Page 35: Working With Scenarios
SIP User's Manual 3. Web-Based Management 3.3.5 Working with Scenarios The Web interface allows you to create your own "menu" with up to 20 pages selected from the menus in the Navigation tree (i.e., pertaining to the Configuration, Management, and Status &...
Page 36: Figure 3-15: Creating A Scenario
MediaPack Series Click the Next button located at the bottom of the page; the Step is added to the Scenario and appears in the Scenario Step list: Figure 3-15: Creating a Scenario Repeat steps 5 through 8 to add additional Steps (i.e., pages). When you have added all the required Steps for your Scenario, click the Save &...
Page 37: Accessing A Scenario
SIP User's Manual 3. Web-Based Management 3.3.5.2 Accessing a Scenario Once you have created the Scenario, you can access it at anytime by following the procedure below: To access the Scenario, take these 2 steps: On the Navigation bar, select the Scenario tab; a message box appears, requesting you to confirm the loading of the Scenario.
Page 38: Editing A Scenario
MediaPack Series To navigate between Scenario Steps, you can perform one of the following: In the Navigation tree, click the required Scenario Step. In an opened Scenario Step (i.e., page appears in the Work pane), use the following navigation buttons: •...
Page 39: Saving A Scenario To A Pc
SIP User's Manual 3. Web-Based Management • Edit the Step Name: In the Navigation tree, select the required Step. In the 'Step Name' field, modify the Step name. In the page, click Next. • Edit the Scenario Name: In the 'Scenario Name' field, edit the Scenario name. In the displayed page, click Next.
Page 40: Loading A Scenario To The Device
MediaPack Series To save a Scenario to a PC, take these 5 steps: On the Navigation bar, click the Scenarios tab; the Scenario appears in the Navigation tree. Click the Get/Send Scenario File button (located at the bottom of the Navigation tree);...
Page 41: Deleting A Scenario
SIP User's Manual 3. Web-Based Management Click the Browse button, and then navigate to the Scenario file stored on your PC. Click the Send File button. Notes: • You can only load a Scenario file to a device that has an identical hardware configuration setup to the device in which it was created.
Page 42: Exiting Scenario Mode
MediaPack Series Click the Delete Scenario File button; a message box appears requesting confirmation for deletion. Figure 3-20: Message Box for Confirming Scenario Deletion Click OK; the Scenario is deleted and the Scenario mode closes. Note: You can also delete a Scenario using the following alternative methods: •...
Page 43: Customizing The Web Interface
The figure below shows an example of a customized Title bar. The top image displays the Title bar with AudioCodes logo and product name. The bottom image displays a customized Title bar with a different image logo and product name.
Page 44: Figure 3-23: Image Download Screen
MediaPack Series On the left pane, click Image Load to Device; the 'Image Download' page is displayed, as shown in the figure below: Figure 3-23: Image Download Screen Click the Browse button, and then navigate to the folder in which the logo image file that you want to use is located.
Page 45: Table 3-2: Ini File Parameters For Changing Logo Image
The corporate logo can be replaced with a text string instead of an image. To replace AudioCodes’ default logo with a text string using the ini file, configure the ini file parameters listed in the table below. (For a description on using the ini file, refer to ''Modifying an ini File'' on page 231.)
Page 46: Customizing The Product Name
MediaPack Series 3.3.6.2 Customizing the Product Name You can customize the product name (text) that appears in the Title bar, using the ini file parameters listed in the table below. (For a description on using the ini file, refer to ''Modifying an ini File'' on page 231.) Table 3-4: ini File Parameters for Customizing Product Name Parameter...
Page 47: Getting Help
SIP User's Manual 3. Web-Based Management 3.3.7 Getting Help The Web interface provides you with context-sensitive Online Help. The Online Help provides you with brief descriptions of most of the parameters you'll need to successfully configure the device. The Online Help provides descriptions of parameters pertaining to the currently opened page.
Page 48: Using The Home Page
MediaPack Series 3.3.8 Using the Home Page The 'Home' page provides you with a graphical display of the device's front panel, displaying color-coded status icons for monitoring the functioning of the device. By default, the 'Home' page is displayed when you access the device's Web interface. When you are configuring the device (in a configuration page), you can always return to the 'Home' page, by simply clicking the Home icon on the toolbar.
Page 49: Assigning A Name To A Port
SIP User's Manual 3. Web-Based Management Item# / Label Description Channel / Displays the status of the ports (channels): Ports (red): line not connected (only applicable to FXO devices) (grey): channel inactive (blue): handset is off-hook (green): active RTP stream You can also view the channel's port settings (refer to "Viewing Port Information"...
Page 50: Resetting An Analog Channel
MediaPack Series To view detailed port information, take these 3 steps: Click the port for which you want to view port settings; the shortcut menu appears. Figure 3-30: Accessing Port Settings from Shortcut Menu (e.g., MP-11x) From the shortcut menu, click Port Settings; the 'Basic Channel Information' page appears.
Page 51: Logging Off The Web Interface
SIP User's Manual 3. Web-Based Management 3.3.9 Logging Off the Web Interface You can log off the Web interface and re-access it with a different user account. For detailed information on the Web User Accounts, refer to User Accounts. To log off the Web interface, take these 2 steps: On the toolbar, click the Log Off button;...
Page 52: Configuration Tab
MediaPack Series Configuration Tab The Configuration tab on the Navigation bar displays all menus related to device configuration. These menus appear in the Navigation tree and include the following: Network Settings (refer to ''Network Settings'' on page 52) Media Settings (refer to ''Media Settings'' on page 67) Security Settings (refer to ''Security Settings'' on page 79) Protocol Configuration (refer to ''Protocol Configuration'' on page 99) Advanced Applications (refer to ''Advanced Applications'' on page 187)
Page 53: Figure 3-35: Ip Settings Page
SIP User's Manual 3. Web-Based Management To configure the IP settings parameters, take these 4 steps: Open the 'IP Settings' page (Configuration tab > Network Settings menu > IP Settings page item). Figure 3-35: IP Settings Page Configure the IP parameters according to the table below. Click the Submit button to save your changes.
Page 54: Table 3-7: Network Settings -- Ip Settings Parameters
MediaPack Series Table 3-7: Network Settings -- IP Settings Parameters Parameter Description IP Settings IP Networking Mode Determines the IP network scheme. [EnableMultipleIPs] [0] Single IP Network = Single IP network (default). [1] Multiple IP Networks = Multiple IP networks (OAMP, Media, and Control).
Page 55 SIP User's Manual 3. Web-Based Management Parameter Description Control Network Settings (Available only in Multiple IP and Dual IP modes.) IP Address The device's source IP address in the Control network. [LocalControlIPAddress] The default value is 0.0.0.0. Subnet Mask The device's subnet mask in the Control network. [LocalControlSubnetMask] The default subnet mask is 0.0.0.0.
Page 56: Configuring The Multiple Interface Table
MediaPack Series 3.4.1.2 Configuring the Multiple Interface Table The 'Multiple Interface Table' page allows you to configure up to three logical network interfaces, each with its own IP address, unique VLAN ID (if enabled), interface name, and application types (i.e., Control, Media, and/or Operations, Administration, Maintenance and Provisioning - OAMP) permitted on the interface.
Page 57: Table 3-8: Multiple Interface Table Parameters Description
SIP User's Manual 3. Web-Based Management Notes: • When adding more than one interface to the table, ensure that you enable VLANs, using the 'VLAN Mode' (VlANMode) parameter. • When booting using BootP/DHCP protocols (refer to the Product Reference Manual), an IP address is obtained from the server. This address is used as the OAMP address for this session, overriding the IP address you configured in the 'Multiple Interface Table' page.
Page 58: Parameter Description
MediaPack Series Parameter Description This column lists the number of ‘1’ bits in the subnet mask (i.e., replaces the standard dotted-decimal representation of the subnet mask for IPv4 interfaces). For example: A subnet mask of 255.0.0.0 is represented by a prefix length of 8 (i.e., 11111111 00000000 00000000 00000000), and a subnet mask of 255.255.255.252 is represented by a prefix length of 30 (i.e., 11111111 11111111 11111111 11111100).
Page 59: Configuring The Application Settings
SIP User's Manual 3. Web-Based Management 3.4.1.3 Configuring the Application Settings The 'Application Settings' page is used for configuring various application parameters such as Telnet. To configure the Application settings parameters, take these 4 steps: Open the 'Application Settings' page (Configuration tab > Network Settings menu > Application Settings page item).
Page 60: Table 3-9: Application Settings Parameters
[NTPUpdateInterval] The default interval is 86400 (i.e., 24 hours). The range is 0 to 214783647. Note: AudioCodes does not recommend setting this parameter to beyond one month (i.e., 2592000 seconds). Telnet Settings Embedded Telnet Server Enables or disables the device's embedded Telnet server. Telnet is [TelnetServerEnable] disabled by default for security reasons.
Page 61 SIP User's Manual 3. Web-Based Management Parameter Description STUN is used to discover whether the device is located behind a NAT and the type of NAT. In addition, it is used to determine the IP addresses and port numbers that the NAT assigns to outgoing signaling messages (using SIP) and media streams (using RTP, RTCP and T.38).
Page 62: Configuring The Nfs Settings
MediaPack Series 3.4.1.4 Configuring the NFS Settings Network File System (NFS) enables the device to access a remote server's shared files and directories, and to handle them as if they're located locally. You can configure up to five different NFS file systems. As a file system, the NFS is independent of machine types, OSs, and network architectures.
Page 63: Configuring The Ip Routing Table
SIP User's Manual 3. Web-Based Management Table 3-10: Network Settings -- NFS Settings Parameters Parameter Description The row index of the remote file system. Index The valid range is 0 to 4. The domain name or IP address of the NFS server. If a domain name is HostOrIP provided, a DNS server must be configured.
Page 64: Figure 3-40: Ip Routing Table Page
MediaPack Series To configure static IP routing, take these 3 steps: Open the 'IP Routing Table' page (Configuration tab > Network Settings menu > IP Routing Table page item). Figure 3-40: IP Routing Table Page In the 'Add a new table entry' group, add a new static routing rule according to the parameters described in the table below.
Page 65: Configuring The Qos Settings
SIP User's Manual 3. Web-Based Management Parameter Description Gateway IP Address The IP address of the router (next hop) to which the packets are [RoutingTableGatewaysColum sent if their destination matches the rules in the adjacent columns. Note: The Gateway address must be in the same subnet on which the address is configured on the 'Multiple Interface Table' page (refer to ''Configuring the Multiple Interface Table'' on page 56).
Page 66: Table 3-12: Qos Settings Parameters
MediaPack Series Configure the QoS parameters according to the table below. Click the Submit button to save your changes. To save the changes to flash memory, refer to ''Saving Configuration'' on page 207. Table 3-12: QoS Settings Parameters Parameter Description Priority Settings Network Priority Defines the priority for Network Class of Service (CoS)
Page 67: Media Settings
SIP User's Manual 3. Web-Based Management 3.4.2 Media Settings The Media Settings menu allows you to configure the device's channel parameters. These parameters are applied to all the device's channels. This menu contains the following page items: Voice Settings (refer to ''Configuring the Voice Settings'' on page 67) Fax/Modem/CID Settings (refer to ''Configuring the Fax / Modem / CID Settings'' on page 70) RTP/RTCP Settings (refer to ''Configuring the RTP / RTCP Settings'' on page 74)
Page 68: Table 3-13: Media Settings, Voice Settings Parameters
MediaPack Series Configure the Voice parameters according to the table below. Click the Submit button to save your changes. To save the changes to flash memory, refer to ''Saving Configuration'' on page 207. Table 3-13: Media Settings, Voice Settings Parameters Parameter Description Voice Volume...
Page 69 SIP User's Manual 3. Web-Based Management Parameter Description DTMF Volume (-31 to 0 dB) DTMF gain control value (in decibels) to the or analog side. [DTMFVolume] The valid range is -31 to 0 dB. The default value is -11 dB. Enable Answer Detector N/A.
Page 70: Configuring The Fax / Modem / Cid Settings
MediaPack Series 3.4.2.2 Configuring the Fax / Modem / CID Settings The 'Fax/Modem/CID Settings' page is used for configuring fax, modem, and Caller ID (CID) parameters. To configure the fax, modem, and CID parameters, take these 4 steps: Open the 'Fax/Modem/CID Settings' page (Configuration tab > Media Settings menu >...
Page 71 SIP User's Manual 3. Web-Based Management Parameter Description Caller ID Transport Type Determines the device's behavior for Caller ID detection. [CallerIDTransportType] [0] Disable = Caller ID is not detected - DTMF digits remain in the voice stream. [1] Relay = Caller ID is detected - DTMF digits are erased from the voice stream.
Page 72 MediaPack Series Parameter Description V.23 Modem Transport Type V.23 Modem Transport Type used by the device. [V23ModemTransportType] [0] Disable = Disable (Transparent) [1] Enable Relay = N/A [2] Enable Bypass = (default) [3] Events Only = Transparent with Events V.32 Modem Transport Type V.32 Modem Transport Type used by the device.
Page 73 SIP User's Manual 3. Web-Based Management Parameter Description Fax/Modem Bypass Coder Type Coder used by the device when performing fax/modem bypass. [FaxModemBypassCoderType] Usually, high-bit-rate coders such as G.711 should be used. [0] G.711Alaw= G.711 A-law 64 (default). [1] G.711Mulaw = G.711 µ-law. Fax/Modem Bypass Packing Number of (20 msec) coder payloads that are used to generate a Factor...
Page 74: Configuring The Rtp / Rtcp Settings
MediaPack Series 3.4.2.3 Configuring the RTP / RTCP Settings The 'RTP/RTCP Settings' page allows you to configure the Real-Time Transport Protocol (RTP) and Real-Time Transport (RTP) Control Protocol (RTCP) parameters. To configure the RTP / RTCP parameters, take these 4 steps: Open the 'RTP/RTCP Settings' page (Configuration tab >...
Page 75 SIP User's Manual 3. Web-Based Management Parameter Description RTP Redundancy Depth Determines whether the device generates redundant packets. [RTPRedundancyDepth] [0] 0 = Disable the generation of redundant packets (default). [1] 1 = Enable the generation of RFC 2198 redundancy packets. Packing Factor N/A.
Page 76 MediaPack Series Parameter Description RTP Base UDP Port Lower boundary of UDP port used for RTP, RTCP (RTP port + 1) [BaseUDPPort] and T.38 (RTP port + 2). The upper boundary is the Base UDP Port + 10 * (number of device's channels). The range of possible UDP ports is 6,000 to 64,000.
Page 77: Configuring The General Media Settings
SIP User's Manual 3. Web-Based Management 3.4.2.4 Configuring the General Media Settings The 'General Media Settings' page allows you to configure various media parameters. To configure general media parameters, take these 4 steps: Open the 'General Media Settings' page (Configuration tab > Media Settings menu >...
Page 78: Configuring The Hook-Flash Settings
MediaPack Series 3.4.2.5 Configuring the Hook-Flash Settings The 'Hook-Flash Settings' page allows you to configure hook-flash parameters. To configure the Hook-Flash parameters, take these 4 steps: Open the 'Hook-Flash Settings' page (Configuration tab > Media Settings menu > Hook-Flash Settings page item). Figure 3-46: Hook-Flash Settings Page Configure the hook-flash parameters according to the table below.
Page 79: Security Settings
SIP User's Manual 3. Web-Based Management 3.4.3 Security Settings The Security Settings menu allows you to configure various security settings. This menu contains the following page items: Web User Accounts (refer to ''Configuring the Web User Accounts'' on page 79) Web &...
Page 80: Figure 3-47: Web User Accounts Page (For Users With 'Security Administrator' Privileges)
MediaPack Series The default attributes for the two Web user accounts are shown in the following table: Table 3-19: Default Attributes for the Web User Accounts Account / Attribute User Name Password Access Level (Case-Sensitive) (Case-Sensitive) Primary Account Admin Admin Security Administrator User User...
Page 81: Configuring The Web And Telnet Access List
SIP User's Manual 3. Web-Based Management To change the password of an account, perform the following: In the field 'Current Password', enter the current password (maximum of 19 case- sensitive characters). In the fields 'New Password' and 'Confirm New Password', enter the new password.
Page 82: Figure 3-48: Web & Telnet Access List Page - Add New Entry
MediaPack Series To add authorized IP addresses for Web and Telnet interfaces access, take these 4 steps: Open the 'Web & Telnet Access List' page (Configuration tab > Security Settings menu > Web & Telnet Access List page item). Figure 3-48: Web & Telnet Access List Page - Add New Entry To add an authorized IP address, in the 'Add a New Authorized IP Address' field, enter the required IP address, and then click Add New Address;...
Page 83: Configuring The Firewall Settings
SIP User's Manual 3. Web-Based Management 3.4.3.3 Configuring the Firewall Settings The device provides an internal firewall, allowing you (the security administrator) to define network traffic filtering rules. You can add up to 50 ordered firewall rules. For each packet received on the network interface, the table is scanned from the top down until a matching rule is found.
Page 84: Table 3-20: Internal Firewall Parameters
MediaPack Series To activate a de-activated rule, take these 2 steps: In the 'Edit Rule' column, select the de-activated rule that you want to activate. Click the Activate button; the rule is activated. To de-activate an activated rule, take these 2 steps: In the 'Edit Rule' column, select the activated rule that you want to de-activate..
Page 85: Configuring The Certificates
SIP User's Manual 3. Web-Based Management 3.4.3.4 Configuring the Certificates The 'Certificates' page is used for the following: Replacing the server certificate (refer to ''Server Certificate Replacement'' on page 85) Replacing the client certificates (refer to ''Client Certificates'' on page 87) Regenerating Self-Signed Certificates (refer to ''Self-Signed Certificates'' on page 88) Updating the private key (using HTTPSPkeyFileName, as described in the Product Reference Manual).
Page 86: Figure 3-51: Certificates Signing Request Page
MediaPack Series Open the ‘Certificates Signing Request' page (Configuration tab > Security Settings menu > Certificates page item). Figure 3-51: Certificates Signing Request Page In the 'Subject Name' field, enter the DNS name, and then click Generate CSR. A textual certificate signing request that contains the SSL device identifier is displayed. Copy this text and send it to your security provider.
Page 87: Client Certificates
SIP User's Manual 3. Web-Based Management 3.4.3.4.2 Client Certificates By default, Web servers using SSL provide one-way authentication. The client is certain that the information provided by the Web server is authentic. When an organizational PKI is used, two-way authentication may be desired: both client and server should be authenticated using X.509 certificates.
Page 88 MediaPack Series 3.4.3.4.3 Self-Signed Certificates The device is shipped with an operational, self-signed server certificate. The subject name for this default certificate is 'ACL_nnnnnnn', where nnnnnnn denotes the serial number of the device. However, this subject name may not be appropriate for production and can be changed while still using self-signed certificates.
Page 89: Configuring The General Security Settings
SIP User's Manual 3. Web-Based Management 3.4.3.5 Configuring the General Security Settings The 'General Security Settings' page is used to configure various security features. To configure the general security parameters, take these 4 steps: Open the 'General Security Settings' page (Configuration tab > Security Settings menu >...
Page 90: Table 3-21: General Security Parameters
MediaPack Series Table 3-21: General Security Parameters Parameter Description HTTP Authentication Mode Determines the authentication mode for the Web interface. [WebAuthMode] [0] Basic Mode = Basic authentication (clear text) is used (default). [1] Digest When Possible = Digest authentication (MD5) is used.
Page 91 SIP User's Manual 3. Web-Based Management Parameter Description Use RADIUS for Web/Telnet Uses RADIUS queries for Web and Telnet interface authentication. Login [0] Disable (default). [WebRADIUSLogin] [1] Enable. When enabled, logging in to the device's Web and Telnet embedded servers is performed via a RADIUS server. The device contacts a predefined server and verifies the given user name and password pair against a remote database, in a secure manner.
Page 92 MediaPack Series Parameter Description RADIUS VSA Vendor ID Defines the vendor ID that the device accepts when parsing a [RadiusVSAVendorID] RADIUS response packet. The valid range is 0 to 0xFFFFFFFF. The default value is 5003. RADIUS VSA Access Level Defines the code that indicates the access level attribute in the Attribute Vendor Specific Attributes (VSA) section of the received RADIUS [RadiusVSAAccessAttribute]...
Page 93: Configuring The Ipsec Table
SIP User's Manual 3. Web-Based Management 3.4.3.6 Configuring the IPSec Table The 'IPSec Table' page allows you to configure the Security Policy Database (SPD) parameters for IP security (IPSec). Note: You can also configure the IPSec table using the ini file table parameter IPSEC_SPD_TABLE (refer to ''Security Parameters'' on page 248).
Page 94: Table 3-22: Default Ike Second Phase Proposals
MediaPack Series If no IPSec methods are defined (Encryption / Authentication), the default settings, shown in the following table are applied. Table 3-22: Default IKE Second Phase Proposals Proposal Encryption Authentication Proposal 0 3DES SHA1 3DES Proposal 1 Proposal 2 SHA1 Proposal 3 Table 3-23: IPSec SPD Table Configuration Parameters...
Page 95 SIP User's Manual 3. Web-Based Management Parameter Name Description Protocol Defines the protocol type to which the IPSec [IPSecPolicyProtocol] mechanism is applied. 0 = Any protocol (default). 17 = UDP. 6 = TCP. Any other protocol type defined by IANA (Internet Assigned Numbers Authority).
Page 96: Configuring The Ike Table
MediaPack Series 3.4.3.7 Configuring the IKE Table The 'IKE Table' page is used to configure the Internet Key Exchange (IKE) parameters. Note: You can also configure the IKE table using the ini file table parameter IPSec_IKEDB_Table (refer to ''Security Parameters'' on page 248). To configure the IKE table, take these 5 steps: Open the ‘IKE Table’...
Page 97: Table 3-24: Default Ike First Phase Proposals
SIP User's Manual 3. Web-Based Management If no IKE methods are defined (Encryption / Authentication / DH Group), the default settings (shown in the following table) are applied. Table 3-24: Default IKE First Phase Proposals Proposal Encryption Authentication DH Group Proposal 0 3DES SHA1...
Page 98 MediaPack Series Parameter Name Description IKE SA LifeTime (KB) Determines the lifetime (in kilobytes) that the SA negotiated in the first IKE session (main mode) is valid. After this size is reached, the SA is re-negotiated. The default value is 0 (i.e., this parameter is ignored). These lifetime parameters [IKE SA LifeTime (sec) and IKE SA LifeTime (KB)] determine the duration the SA created in the main mode phase is valid.
Page 99: Protocol Configuration
SIP User's Manual 3. Web-Based Management 3.4.4 Protocol Configuration The Protocol Configuration menu allows you to configure the device's SIP parameters and contains the following submenus: Protocol Definition (refer to ''Configuring the Protocol Definition Parameters'' on page SIP Advanced Parameters (refer to ''Configuring the SIP Advanced Parameters'' on page 126) Manipulation Tables (refer to ''Configuring the Number Manipulation Tables'' on page 148)
Page 100: Figure 3-55: Sip General Parameters Page
MediaPack Series 3.4.4.1.1 SIP General Parameters The 'SIP General Parameters' page is used to configure general SIP parameters. To configure the general SIP protocol parameters, take these 4 steps: Open the 'SIP General Parameters' page (Configuration tab > Protocol Configuration menu > Protocol Definition submenu > SIP General Parameters page item).
Page 101: Table 3-26: Sip General Parameters (Protocol Definition)
SIP User's Manual 3. Web-Based Management Configure the parameters according to the table below. Click the Submit button to save your changes. To save the changes to flash memory, refer to ''Saving Configuration'' on page 207. Table 3-26: SIP General Parameters (Protocol Definition) Parameter Description PRACK Mode...
Page 102 MediaPack Series Parameter Description Enable Early Media Enables the device to send a 183 Session Progress response with SDP [EnableEarlyMedia] (instead of 180 Ringing), allowing the media stream to be established prior to the answering of the call. [0] Disable = Early Media is disabled (default). [1] Enable = Enables Early Media.
Page 103 SIP User's Manual 3. Web-Based Management Parameter Description Fax Signaling Method Determines the SIP signaling method for establishing and transmitting a [IsFaxUsed] fax session after a fax is detected. [0] No Fax = No fax negotiation using SIP signaling. Fax transport method is according to the parameter FaxTransportMode (default).
Page 104 MediaPack Series Parameter Description SIP TCP Local Port Local TCP port for SIP messages. [TCPLocalSIPPort] The valid range is 1 to 65534. The default value is 5060. SIP TLS Local Port Local TLS port for SIP messages. The valid range is 1 to 65534. The default value is 5061. [TLSLocalSIPPort] Note: The value of must be different than the value of 'SIP TCP Local Port' (TCPLocalSIPPort).
Page 105 SIP User's Manual 3. Web-Based Management Parameter Description Add Number Plan and Determines whether the TON/PLAN parameters are included in the Type to Remote Party ID Remote-Party-ID (RPID) header. Header [0] No [AddTON2RPI] [1] Yes (default) If RPID header is enabled (EnableRPIHeader = 1) and AddTON2RPI = 1, it's possible to configure the calling and called number type and number plan using the Number Manipulation tables for Tel-to-IP calls.
Page 106 MediaPack Series Parameter Description Use Source Number as Determines the use of Tel Source Number and Display Name for Tel-to-IP Display Name calls. [UseSourceNumberAsD [0] No = If a Tel Display Name is received, the Tel Source Number is isplayName] used as the IP Source Number and the Tel Display Name is used as the IP Display Name.
Page 107 SIP User's Manual 3. Web-Based Management Parameter Description Determines the method used to play a ringback tone to the Tel side. Play Ringback Tone to [0] Don't Play = Ringback tone isn't played. [PlayRBTone2Tel] [1] Play Local = Ringback tone is played to the Tel side of the call when 180/183 response is received.
Page 108 Defines the string that is used in the SIP request header User-Agent and [UserAgentDisplayInfo] SIP response header Server. If not configured, the default string 'AudioCodes product-name s/w-version' is used (e.g., User-Agent: Audiocodes-Sip-Gateway-MP/v.5.40.010.006). When configured, the string 'UserAgentDisplayInfo s/w-version' is used (e.g., User-Agent: MyNewOEM/v.5.40.010.006).
Page 109 SIP User's Manual 3. Web-Based Management Parameter Description Enable P-Charging Enables the addition of a P-Charging-Vector header to all outgoing INVITE Vector messages. [EnablePChargingVecto [0] Disable = Disable (default) [1] Enable = Enable Enable VoiceMail URI Enables or disables the interworking of target and cause for redirection from Tel to IP and vice versa, according to RFC 4468.
Page 110: Figure 3-56: Proxy & Registration Parameters Page
MediaPack Series 3.4.4.1.2 Proxy & Registration Parameters The 'Proxy & Registration' page allows you to configure parameters that are associated with Proxy and Registration. Note: To view whether the device or its endpoints have registered to a SIP Registrar/Proxy server, refer to 'Registration Status'' on page 223. To configure the Proxy &...
Page 111 SIP User's Manual 3. Web-Based Management Parameter Description [1] Use Proxy = Proxy is used. Parameters relevant to Proxy configuration are displayed. If you are using a Proxy server, enter the IP address of the Proxy server in the 'Proxy Sets table' (refer to ''Proxy Sets Table'' on page 117). If you are not using a Proxy server, you must configure the device's 'Tel to IP Routing' table (described in ''Tel to IP Routing Table'' on page 156).
Page 112 MediaPack Series Parameter Description Use Routing Table for Use the internal 'Tel to IP Routing' table to obtain the URI Host name and Host Names and (optionally) an IP profile (per call), even if a Proxy server is used. Profiles [0] Disable = Don't use (default).
Page 113 SIP User's Manual 3. Web-Based Management Parameter Description Registrar IP Address The IP address (or FQDN) and optionally, port number of the SIP Registrar [RegistrarIP] server. The IP address is in dotted-decimal notation, e.g., 201.10.8.1:<5080>. Notes: If not specified, the REGISTER request is sent to the primary Proxy server.
Page 114 MediaPack Series Parameter Description Miscellaneous parameters Gateway Name Assigns a name to the device (e.g., 'gateway1.com'). Ensure that the name you choose is the one with which the Proxy is configured to identify the [SIPGatewayName] device. Note: If specified, the device name is used as the host part of the SIP URI in the From header.
Page 115 SIP User's Manual 3. Web-Based Management Parameter Description addresses. Therefore, if the first SRV query returns two domain names, and the A-record queries return two IP addresses each, no additional searches are performed. If set to NAPTR [2], an NAPTR query is performed. If it is successful, an SRV query is sent according to the information received in the NAPTR response.
Page 116 MediaPack Series Parameter Description Cnonce Cnonce string used by the SIP server and client to provide mutual [Cnonce] authentication. (Free format, i.e., 'Cnonce = 0a4f113b'). The default is 'Default_Cnonce'. Authentication Mode Determines the device's registration and authentication method. [AuthenticationMode] [0] Per Endpoint = Registration and Authentication separately for each endpoint.
Page 117: Figure 3-57: Proxy Sets Table
SIP User's Manual 3. Web-Based Management 3.4.4.1.3 Proxy Sets Table The 'Proxy Sets Table' page allows you to define up to six groups of logical IP addresses (i.e., Proxy Sets), each containing up to five Proxy server IP addresses or FQDN's. In addition, Proxy load balancing and redundancy mechanisms can be applied per Proxy Set (if a Proxy Set contains more than one Proxy).
Page 118: Table 3-28: Proxy Sets Table Parameters
MediaPack Series Table 3-28: Proxy Sets Table Parameters Parameter Description Proxy Set ID The Proxy Set identification number. The valid range is 0 to 5 (i.e., up to 6 Proxy Set ID's can be configured). The Proxy Set ID #0 is used as the default Proxy Set, and if defined is backward compatible to the list of Proxies from earlier releases.
Page 119 SIP User's Manual 3. Web-Based Management Parameter Description Transport Type The transport type per Proxy server. [0] UDP [1] TCP [2] TLS [-1] = Undefined Note: If no transport type is selected, the value of the global parameter SIPTransportType is used (refer to ''SIP General Parameters'' on page 100). Proxy Load Balancing Enables the Proxy Load Balancing mechanism per Proxy Set ID.
Page 120 MediaPack Series Parameter Description Enable Proxy Keep Determines whether Keep-Alive with the Proxy is enabled or disabled. This Alive parameter is configured per Proxy Set. [EnableProxyKeepAli [0] Disable = Disable (default). [1] Using OPTIONS = Enables Keep-Alive with Proxy using OPTIONS. [2] Using REGISTER = Enable Keep-Alive with Proxy using REGISTER.
Page 121: Table 3-29: Supported Coders
SIP User's Manual 3. Web-Based Management 3.4.4.1.4 Coders The 'Coders' page allows you to configure up to five coders (and their attributes) for the device. The first coder in the list is the highest priority coder and is used by the device whenever possible.
Page 122: Figure 3-58: Coders
MediaPack Series To configure the device's coders, take these 9 steps: Open the 'Coders' page (Configuration tab > Protocol Configuration menu > Protocol Definition submenu > Coders page item). Figure 3-58: Coders Page From the 'Coder Name' drop-down list, select the coder you want to use. For the full list of available coders and their corresponding attributes, refer to the table below.
Page 123: Table 3-30: Dtmf And Dialing Parameters
SIP User's Manual 3. Web-Based Management 3.4.4.1.5 DTMF & Dialing Parameters The 'DTMF & Dialing' page is used to configure parameters associated with dual-tone multi-frequency (DTMF) and dialing. To configure the DTMF and dialing parameters, take these 4 steps: Open the 'DTMF & Dialing' page (Configuration tab > Protocol Configuration menu >...
Page 124 MediaPack Series Parameter Description Inter Digit Timeout for Defines the time (in seconds) that the device waits between digits that are Overlap Dialing [sec] received (i.e., dialed) from the Tel side when Tel-to-IP overlap dialing is [TimeBetweenDigits] performed . When this inter-digit timeout expires, the device uses the collected digits for the called destination number.
Page 125 SIP User's Manual 3. Web-Based Management Parameter Description RFC 2833 Payload Type The RFC 2833 DTMF relay dynamic payload type. [RFC2833PayloadType] The valid range is 96 to 99, and 106 to 127. The default is 96. The 100, 102 to 105 range is allocated for proprietary usage. Notes: Certain vendors (e.g., Cisco) use payload type 101 for RFC 2833.
Page 126: Configuring The Sip Advanced Parameters
MediaPack Series Parameter Description Dial Tone Duration [sec] Duration (in seconds) that the dial tone is played. [TimeForDialTone] FXS interface plays the dial tone after the phone is picked up (off-hook); while FXO interface plays the dial tone after port is seized in response to ringing (from PBX/PSTN).
Page 127: Figure 3-60: Advanced Parameters
SIP User's Manual 3. Web-Based Management 3.4.4.2.1 Advanced Parameters The 'Advanced Parameters' page allows you to configure general control protocol parameters. To configure the advanced protocol parameters, take these 4 steps: Open the 'Advanced Parameters' page (Configuration tab > Protocol Configuration menu >...
Page 128: Table 3-31: Advanced Parameters Description
MediaPack Series Table 3-31: Advanced Parameters Description Parameter Description General IP Security Determines whether the device accepts SIP calls received only from IP [SecureCallsFromIP] addresses listed in the 'Tel to IP Routing' table (refer to ''Tel to IP Routing Table'' on page 156). This is useful in preventing unwanted SIP calls or messages and/or VoIP spam.
Page 129 SIP User's Manual 3. Web-Based Management Parameter Description follows: d1005, dpp699, p9p300. To add the 'd' and 'p' digits, use the usual number manipulation rules. To use this feature with FXO interfaces, configure the device to operate in one-stage dialing mode. If this parameter is enabled, it is possible to configure the FXS/FXO interface to wait for dial tone per destination phone number (before or during dialing of destination phone number).
Page 130 MediaPack Series Parameter Description signal is detected (applicable only to one-stage dialing) and releases a call when a second polarity reversal signal is detected. Enable Current Disconnect Enables call release upon detection of a current disconnect signal. [EnableCurrentDisconnec [0] Disable = Disable the current disconnect service (default). [1] Enable = Enable the current disconnect service.
Page 131 SIP User's Manual 3. Web-Based Management Parameter Description Silence Detection Period Duration of silence period (in seconds) prior to call disconnection. [sec] The range is 10 to 28,800 (i.e., 8 hours). The default is 120 seconds. [FarEndDisconnectSilenc ePeriod] Silence Detection Method Silence detection method.
Page 132 MediaPack Series Parameter Description Debug Level Syslog debug logging level. [GwDebugLevel] [0] 0 = Debug is disabled (default). [1] 1 = Flow debugging is enabled. [2] 2 = Flow and device interface debugging are enabled. [3] 3 = Flow, device interface, and stack interface debugging are enabled.
Page 133 SIP User's Manual 3. Web-Based Management Parameter Description Default Release Cause Default Release Cause (to IP) for IP-to-Tel calls when the device initiates [DefaultReleaseCause] a call release and an explicit matching cause for this release isn't found. The default release cause is NO_ROUTE_TO_DESTINATION (3). Other common values include NO_CIRCUIT_AVAILABLE (34), DESTINATION_OUT_OF_ORDER (27), etc.
Page 134 MediaPack Series Parameter Description Enable Calls Cut Through Enables users to receive incoming IP calls while the port is in off-hook [CutThrough] state. [0] Disable = Disabled (default). [1] Enable = Enabled. If enabled, the FXS interface answers the call and 'cuts through' the voice channel if there is no other active call on the port, even if the port is in off-hook state.
Page 135: Figure 3-61: Supplementary Services
SIP User's Manual 3. Web-Based Management Parameter Description Emergency Calls Determines the time (in minutes) that the device waits before tearing- Reanswer Timeout down an emergency call (defined by the parameter [EmergencyRegretTimeo EmergencyNumbers). Until this time expires, an emergency call can only be disconnected by the remote party [(typically, by a Public Safety Answering Point (PSAP)].
Page 136: Table 3-32: Supplementary Services Parameters
MediaPack Series Configure the supplementary services parameters according to the table below. Click the Submit button to save your changes, or click the Subscribe to MWI or Unsubscribe to MWI buttons to save your changes and to subscribe / unsubscribe to the MWI server.
Page 137 SIP User's Manual 3. Web-Based Management Parameter Description Note: To use this service, the devices at both ends must support this option. Enable Call Waiting Determines whether Call Waiting is enabled. [EnableCallWaiting] [0] Disable = Disable the Call Waiting service. [1] Enable = Enable the Call Waiting service (default).
Page 138 MediaPack Series Parameter Description Caller ID Type Defines one of the following standards for detection (FXO) and generation [CallerIDType] (FXS) of Caller ID, and detection (FXO) generation (FXS) of MWI (when specified) signals: [0] Standard Bellcore = Caller ID and MWI (default) [1] Standard ETSI = Caller ID and MWI [2] Standard NTT [4] Standard BT = Britain...
Page 139 SIP User's Manual 3. Web-Based Management Parameter Description MWI Display Determines whether MWI information is sent to the phone display. [MWIDisplay] [0] Disable = MWI information isn't sent to display (default). [1] Enable = The device generates an MWI message (determined by the parameter CallerIDType), which is displayed on the MWI display.
Page 140: Figure 3-62: Metering Tones
MediaPack Series Parameter Description Conference Parameters Enable 3-Way Enables or disables the 3-Way Conference feature. Conference [0] Disable = Disable (default) [Enable3WayConferenc [1] Enable = Enables 3-way conferencing Establish Conference Defines the digit pattern, which upon detection generates the Conference- Code initiating INVITE when 3-way conferencing is enabled (Enable3WayConference is set to 1).
Page 141: Table 3-33: Metering Tones Parameters
SIP User's Manual 3. Web-Based Management Table 3-33: Metering Tones Parameters Parameter Description Generate Metering Tones Determines the method used to configure the metering tones that are [PayPhoneMeteringMod generated to the Tel side. [0] Disable = Metering tones aren't generated (default). [1] Internal Table = Metering tones are generated according to the internal table configured by the parameter ChargeCode.
Page 142: Figure 3-63: Charge Codes Table
MediaPack Series To configure the Charge Codes table, take these 4 steps: Access the 'Charge Codes Table' page (Configuration tab > Protocol Configuration menu > SIP Advanced Parameters submenu > Charge Codes page item). Alternatively, you can also access this page from the 'Metering Tones' page (refer to ''Metering Tones'' on page 140).
Page 143: Figure 3-64: Keypad Features
SIP User's Manual 3. Web-Based Management Notes: • The 'Keypad Features' page is only available if the device supports FXS interface . • The method used by the device to collect dialed numbers is identical to the method used during a regular call (i.e., max digits, interdigit timeout, digit map, etc.).
Page 144: Table 3-34: Keypad Features Parameters Description
MediaPack Series Table 3-34: Keypad Features Parameters Description Parameter Description Forward (Note: The forward type and number can be viewed in the 'Call Forward' table - refer to ''Call Forward'' on page 175.) Unconditional Keypad sequence that activates the immediate call forward option. [KeyCFUnCond] No Answer Keypad sequence that activates the forward on no answer option.
Page 145 SIP User's Manual 3. Web-Based Management Parameter Description Transfer Blind Keypad sequence that activates blind transfer for Tel-to-IP calls. There are [KeyBlindTransfer] two possible scenarios: Option 1: After this sequence is dialed, the current call is put on hold (using Re-INVITE), a dial tone is played to the phone, and then phone number collection starts.
Page 146: Figure 3-65: Sas Configuration
MediaPack Series To utilize the SAS feature, the VoIP CPEs such as IP phones or residential gateways, need to be defined so that their Proxy and Registrar destination addresses and UDP port equal the SAS feature's IP address and SAS local SIP UDP port. The SAS feature operates in one of two modes: Normal Mode: Initially, the SAS feature acts as a registrar so that every VoIP CPE within the SME's LAN registers to it, while the SAS feature passes all registration...
Page 147: Table 3-35: Stand-Alone Survivability Parameters Description
SIP User's Manual 3. Web-Based Management Table 3-35: Stand-Alone Survivability Parameters Description Parameter Description Enable SAS Enables the Stand-Alone Survivability (SAS) feature. [EnableSAS] [0] Disable Disabled (default) [1] Enable = SAS is enabled When enabled, the device receives the registration requests from different SIP entities in the local network and then forwards them to the defined proxy.
Page 148: Configuring The Number Manipulation Tables
MediaPack Series 3.4.4.3 Configuring the Number Manipulation Tables The device provides four Number Manipulation tables for incoming (IP-to-Tel) and outgoing (Tel-to-IP) calls. These tables are used to modify the destination and source telephone numbers so that the calls can be routed correctly. Telephone number manipulation can be implemented for the following usage examples: Strip or add dialing plan digits from or to the number.
Page 149: Figure 3-66: Source Phone Number Manipulation Table For Tel-To-Ip Calls
SIP User's Manual 3. Web-Based Management Figure 3-66: Source Phone Number Manipulation Table for Tel-to-IP Calls The figure above shows an example of the use of manipulation rules in the 'Source Phone Number Manipulation Table for Tel IP Calls': • When the destination number is 035000 and source number is 20155, the source number is changed to 97120155.
Page 150: Table 3-36: Number Manipulation Parameters Description
MediaPack Series Table 3-36: Number Manipulation Parameters Description Parameter Description Destination Prefix Destination (called) telephone number prefix. An asterisk (*) represents any number. Source Prefix Source (caller) telephone number prefix. An asterisk (*) represents any number. Source IP Source IP address of the caller (obtained from the Contact header in the INVITE message).
Page 151: Table 3-37: Dialing Plan Notations
SIP User's Manual 3. Web-Based Management 3.4.4.3.1 Dialing Plan Notation The dialing plan notation applies to all the Number Manipulation tables as well as to the 'Tel to IP Routing' table (refer to ''Tel to IP Routing Table'' on page 156) and to the 'IP to Hunt Group Routing' table (refer to ''IP to Hunt Group Routing'' on page 159).
Page 152: Table 3-38: Phone-Context Parameters Description
MediaPack Series To configure the Phone-Context tables, take these 4 steps: Open the 'Phone Context Table' page (Configuration tab > Protocol Configuration menu > Manipulation Tables submenu > Phone Context Table page item). Figure 3-67: Phone Context Table Page Configure the Phone Context table according to the table below. Click the Submit button to save your changes.
Page 153: Configuring The Routing Tables
SIP User's Manual 3. Web-Based Management Parameter Description Select the Number Type assigned to this entry. If you selected Unknown as the NPI, you can select Unknown [0]. If you selected Private as the NPI, you can select Unknown [0], Level 2 Regional [1], Level 1 Regional [2], PSTN Specific [3], or Level 0 Regional (Local) [4].
Page 154: Table 3-39: Routing General Parameters Description
MediaPack Series Configure the general parameters according to the table below. Click the Submit button to save your changes. To save the changes to flash memory, refer to ''Saving Configuration'' on page 207. Table 3-39: Routing General Parameters Description Parameter Description Add Hunt Group ID as Prefix Determines whether the device's Hunt Group ID is added as a...
Page 155 SIP User's Manual 3. Web-Based Management Parameter Description Enable Alt Routing Tel to IP Enables the Alternative Routing feature for Tel-to-IP calls. [AltRoutingTel2IPEnable] [0] Disable = Disables the Alternative Routing feature (default). [1] Enable = Enables the Alternative Routing feature. [2] Status Only = The Alternative Routing feature is disabled, but read-only information on the Quality of Service of the destination IP addresses is provided.
Page 156 MediaPack Series 3.4.4.4.2 Tel to IP Routing Table The 'Tel to IP Routing' page provides a table for routing Tel calls to IP addresses. This routing table associates a called / calling telephone number's prefixes with a destination IP address or with a Fully Qualified Domain Name (FQDN). When a call is routed by the device (i.e., a Proxy server isn't used), the called and calling numbers are compared to the list of prefixes in this table.
Page 157 SIP User's Manual 3. Web-Based Management Alternative routing (using this table) is commonly implemented when there is no response to an INVITE message (after INVITE retransmissions). The device then issues an internal 408 'No Response' implicit release reason. If this reason is included in the 'Reasons for Alternative Routing' table, the device immediately initiates a call to the redundant destination using the next matched entry in the 'Tel to IP Routing' table.
Page 158: Table 3-40: Tel To Ip Routing Table Parameters Description
MediaPack Series Table 3-40: Tel to IP Routing Table Parameters Description Parameter Description Tel to IP Routing Mode Determines whether to route Tel calls to IP before or after manipulation of [RouteModeTel2IP] destination number. [0] Route calls before manipulation = Tel-to-IP calls are routed before the number manipulation rules are applied (default).
Page 159 SIP User's Manual 3. Web-Based Management Parameter Description IP Profile ID IP profile number assigned to the destination IP address that is defined in the 'Dest. IP Address' field. Status A read-only field representing the Quality of Service of the destination IP address: n/a = Alternative Routing feature is disabled.
Page 160: Table 3-41: Ip To Hunt Group Routing Table Description
MediaPack Series To configure the IP to Hunt Group Routing table, take these 6 steps: Open the 'IP to Hunt Group Routing' page (Configuration tab > Protocol Configuration menu > Routing Tables submenu > IP to Hunt Group Routing page item).
Page 161 SIP User's Manual 3. Web-Based Management Parameter Description Source Host Prefix The From URI host name prefix of the incoming INVITE message. If configured, the device uses it for IP-to-Tel routing. If not used, it must be left empty. Notes: The asterisk (*) symbol cannot be used to depict any source host prefix.
Page 162: Figure 3-70: Internal Dns Table
MediaPack Series 3.4.4.4.4 Internal DNS Table The 'Internal DNS Table' page, similar to a DNS resolution is used to translate up to 10 host (domain) names into IP addresses (e.g., when using the 'Tel to IP Routing' table). Two different IP addresses can be assigned to the same host name, typically used for alternative routing (using the 'Tel to IP Routing' table).
Page 163: Figure 3-71: Internal Srv Table Screen
SIP User's Manual 3. Web-Based Management 3.4.4.4.5 Internal SRV Table The 'Internal SRV Table' page provides a table for resolving host names to DNS A- Records. Three different A-Records can be assigned to each host name. Each A-Record contains the host name, priority, weight, and port. Notes: •...
Page 164: Figure 3-72: Reasons For Alternative Routing
MediaPack Series 3.4.4.4.6 Reasons for Alternative Routing The 'Reasons for Alternative Routing' page includes two groups - IP to Tel Reasons and Tel to IP Reasons. Each group allows you to define up to four different release reasons. If a call is released as a result of one of these reasons, the device tries to find an alternative route for that call.
Page 165: Configuring The Profile Definitions
SIP User's Manual 3. Web-Based Management In the 'IP to Tel Reasons' group, select up to four different call failure reasons that invoke an alternative IP-to-Tel routing. In the 'Tel to IP Reasons' group, select up to four different call failure reasons that invoke an alternative Tel-to-IP routing.
Page 166: Figure 3-73: Coder Group Settings
MediaPack Series 3.4.4.5.1 Coder Group Settings The 'Coder Group Settings' page provides a table for defining up to four different coder groups. These coder groups are used in the 'Tel Profile Settings' and 'IP Profile Settings' pages to assign different coders to Profiles. For each coder group you can define up to five coders, where the first coder (and its attributes) in the table takes precedence over the second coder, and so on.
Page 167 SIP User's Manual 3. Web-Based Management Repeat steps 3 through 7 for the second to fifth coders (optional). Repeat steps 2 through 8 for the second to fourth coder groups (optional). Click the Submit button to save your changes. To save the changes to flash memory, refer to ''Saving Configuration'' on page 207. Notes: •...
Page 168: Figure 3-74: Tel Profile Settings
MediaPack Series 3.4.4.5.2 Tel Profile Settings The 'Tel Profile Settings' page allows you to define up to nine different Tel Profiles. You can then assign these Tel Profiles to the device's channels (in the 'Endpoint Phone Number Table' page), thereby applying different behaviors to different channels (i.e., ports). Note: You can also configure Tel Profiles using the ini file table parameter TelProfile (refer to ''SIP Configuration Parameters'' on page 258).
Page 169 SIP User's Manual 3. Web-Based Management From the 'Profile ID' drop-down list, select the Tel Profile identification number you want to configure. In the 'Profile Name' field, enter an arbitrary name that enables you to easily identify the Tel Profile. From the 'Profile Preference' drop-down list, select the priority of the Tel Profile, where '1' is the lowest priority and '20' is the highest.
Page 170: Figure 3-75: Ip Profile Settings
MediaPack Series 3.4.4.5.3 IP Profile Settings The 'IP Profile Settings' page allows you to define up to nine different IP Profiles. You can then assign these IP Profiles to routing rules in the 'Tel to IP Routing' page (refer to ''Tel to IP Routing Table'' on page 156) and 'IP to Hunt Group Routing' page (refer to ''IP to Hunt Group Routing'' on page 159).
Page 171: Configuring The Endpoint Settings
SIP User's Manual 3. Web-Based Management From the 'Profile Preference' drop-down list, select the priority of the IP Profile, where '1' is the lowest priority and '20' is the highest. If both IP and Tel profiles apply to the same call, the coders and other common parameters (noted by an asterisk in the description of the parameter IPProfile) of the preferred Profile are applied to that call.
Page 172: Figure 3-76: Authentication
MediaPack Series 3.4.4.6.1 Authentication The 'Authentication' page defines a user name and password for authenticating each device port. Authentication is typically used for FXS interfaces, but can also be used for FXO interfaces. Notes: • The 'Authentication Mode' parameter (refer to ''Proxy & Registration Parameters'' on page 110) determines whether authentication is performed per port or for the entire device.
Page 173: Figure 3-77: Automatic Dialing
SIP User's Manual 3. Web-Based Management 3.4.4.6.2 Automatic Dialing The 'Automatic Dialing' page allows you to define a telephone number that is automatically dialed when an FXS or FXO port is used (e.g., off-hooked). To configure Automatic Dialing, take these 5 steps: Open the 'Automatic Dialing' page (Configuration tab >...
Page 174: Figure 3-78: Caller Display Information
MediaPack Series 3.4.4.6.3 Caller Display Information The 'Caller Display Information' page allows you to enable the device to send Caller ID information to IP when a call is made. The called party can use this information for caller identification. The information configured in this page is sent in an INVITE message in the 'From' header.
Page 175: Figure 3-79: Call Forward Table
SIP User's Manual 3. Web-Based Management From the 'Presentation' drop-down list, select one of the following: • 'Allowed' [0] - sends the string defined in the 'Caller ID/Name' field when a Tel-to- IP call is made using the corresponding device port. •...
Page 176: Table 3-43: Call Forward Table
MediaPack Series Table 3-43: Call Forward Table Parameter Description Forward Type Determines the scenario for forwarding a call. [0] Deactivate = Don't forward incoming calls (default). [1] On Busy = Forward incoming calls when the port is busy. [2] Unconditional = Always forward incoming calls. [3] No Answer = Forward incoming calls that are not answered within the time specified in the 'Time for No Reply Forward' field.
Page 177: Figure 3-80: Caller Id Permissions
SIP User's Manual 3. Web-Based Management To configure Caller ID Permissions per port, take these 4 steps: Open the 'Caller ID Permissions' page (Configuration tab > Protocol Configuration menu > Endpoint Settings submenu > Caller ID Permissions page item). Figure 3-80: Caller ID Permissions Page From the 'Caller ID' drop-down list, select one of the following: •...
Page 178: Figure 3-81: Call Waiting
MediaPack Series 3.4.4.6.6 Call Waiting The 'Call Waiting' page allows you to enable or disable call waiting per device FXS port. Notes: • This page is applicable only to FXS interfaces. • Instead of using this page, you can enable or disable call waiting for all the device's ports, using the global call waiting parameter 'Enable Call Waiting' (refer to ''Supplementary Services'' on page 135).
Page 179: Configuring The Endpoint Phone Numbers
SIP User's Manual 3. Web-Based Management 3.4.4.7 Configuring the Endpoint Phone Numbers The 'Endpoint Phone Number Table' page allows you to activate the device's ports (endpoints), by defining telephone numbers for the endpoints and assigning them to Hunt Groups and profiles. Notes: •...
Page 180: Configuring The Hunt And Ip Groups
MediaPack Series Parameter Description Phone Number The telephone number that is assigned to the channel. For a range of channels, only enter the first telephone number. Subsequent channels are assigned the next consecutive telephone number. For example, if you enter 400 for channels 1 to 4, then channel 1 is assigned phone number 400, channel 2 is assigned phone number 401, and so on.
Page 181: Table 3-45: Hunt Group Settings Parameters Description
SIP User's Manual 3. Web-Based Management To configure the Hunt Group Settings table, take these 5 steps: Open the 'Hunt Group Settings' page (Configuration tab > Protocol Configuration menu > Hunt/IP Group submenu > Hunt Group Settings page item). Figure 3-83: Hunt Group Settings Page From the 'Routing Index' drop-down list, select the range of entries that you want to edit (up to 24 entries can be configured).
Page 182 MediaPack Series Mode Description channel in ascending cyclic order is selected. Note that if the called number is found, but the channel associated with the number is busy, the call is released. By Source Phone Number = Selects the channel according to the calling number.
Page 183 Call-ID: 9907977062512000232825@10.33.37.78 CSeq: 3 REGISTER Contact: <sip:101@10.33.37.78>;expires=3600 Expires: 3600 User-Agent: Audiocodes-Sip-Gateway-MP-118 FXS_FXO/v.5.40A.008.002 Content-Length: 0 3.4.4.8.2 Configuring the IP Groups The 'IP Group Table' page allows you to create logical IP entities (IP Groups) that are later used in the call routing tables.
Page 184: Table 3-46: Ip Group Parameters Description
MediaPack Series Notes: • By default, if you disable the use of a proxy (i.e., IsProxyUsed is set to 0), then only one IP Group is defined (and working with multiple IP Groups is not valid). • You can also configure the IP Groups table using the ini file table parameter IPGroup (refer to ''SIP Configuration Parameters'' on page 258).
Page 185: Figure 3-85: Account Table
SIP User's Manual 3. Web-Based Management Parameter Description Send Invite To Proxy Determines whether INVITE messages are sent to the IP Group. Disable (default). Enable = INVITE messages as a result of REFER/3xx messages are sent to the IP Group, overriding the Refer-To/Contact destination. Always Use Route Table Determines the Request URI host name in outgoing INVITE messages.
Page 186: Table 3-47: Account Parameters Description
MediaPack Series Table 3-47: Account Parameters Description Parameter Description Served Trunk Group The Hunt Group ID for which the device performs registration and/or authentication to a destination IP Group (i.e., Serving IP Group). For Tel-to-IP calls, the ServedTrunkGroup is the source Hunt Group from where the call initiated.
Page 187: Advanced Applications
SIP User's Manual 3. Web-Based Management Parameter Description REGISTER sip:audiocodes SIP/2.0 Via: SIP/2.0/UDP 10.33.37.78;branch=z9hG4bKac1397582418 From: <sip:ContactUser@HostName>;tag=1c1397576231 To: <sip: ContactUser@HostName > Call-ID: 1397568957261200022256@10.33.37.78 CSeq: 1 REGISTER Contact: <sip:ContactUser@10.33.37.78>;expires=3600 Expires: 3600 User-Agent: Audiocodes-Sip-Gateway-MP-118 FXS_FXO/v.5.40A.008.002 Content-Length: 0 Note: The TrunkGroup account registration is not effected by the parameter IsRegisterNeeded.
Page 188: Table 3-48: Voice Mail Parameters
MediaPack Series To configure the Voice Mail parameters, take these 4 steps: Open the 'Voice Mail Settings' page (Configuration tab > Advanced Applications menu > Voice Mail Settings page item). Figure 3-86: Voice Mail Settings Page Configure the voice mail parameters according to the table below. Click the Submit button to save your changes.
Page 189 SIP User's Manual 3. Web-Based Management Parameter Description Line Transfer Mode Determines the call transfer method used by the device. [LineTransferMode] [0] None = IP (default). [1] Blind = PBX blind transfer. After receiving a REFER message from the IP side, the FXO sends a hook-flash to the PBX, dials the digits (that are received in the Refer-To header), and then immediately drops the line (on-hook).
Page 190 MediaPack Series Parameter Description Forward on No Answer Determines the digit pattern used by the PBX to indicate 'call forward on Digit Pattern (External) no answer' when the original call is received from an external line (not an [DigitPatternForwardOnN internal extension). oAnswerExt] The valid range is a 120-character string.
Page 191: Configuring Radius Accounting Parameters
SIP User's Manual 3. Web-Based Management Parameter Description SMDI Timeout Determines the time (in msec) that the device waits for an SMDI Call [SMDITimeOut] Status message before or after a SETUP message is received. This parameter synchronizes the SMDI and analog CAS interfaces. If the timeout expires and only an SMDI message is received, the SMDI message is dropped.
Page 192: Configuring The Fxo Parameters
MediaPack Series Parameter Description RADIUS Accounting Type Determines when the RADIUS accounting messages are sent to the [RADIUSAccountingType] RADIUS accounting server. [0] At Call Release = Sent at call release only (default). [1] At Connect & Release = Sent at call connect and release. [2] At Setup &...
Page 193: Table 3-50: Fxo Parameters Description
SIP User's Manual 3. Web-Based Management Table 3-50: FXO Parameters Description Parameter Description Dialing Mode Determines the dialing mode for IP-to-Tel (FXO) calls. [IsTwoStageDial] [0] One Stage = One-stage dialing. [1] Two Stages = Two-stage dialing (default). If two-stage dialing is enabled, the device seizes one of the PSTN/PBX lines without performing any dialing, connects the remote IP user to the PSTN/PBX, and all further signaling (dialing and Call Progress Tones) is performed directly with the PBX without the device's...
Page 194 MediaPack Series Parameter Description Ring Detection Timeout [sec] Defines the timeout (in seconds) for detecting the second ring after the [FXOBetweenRingTime] first detected ring. If automatic dialing is not used and Caller ID is enabled, the device seizes the line after detection of the second ring signal (allowing detection of caller ID sent between the first and the second rings).
Page 195: Management Tab
SIP User's Manual 3. Web-Based Management Parameter Description Disconnect on Dial Tone The device can disconnect a call after a dial tone is detected from the [DisconnectOnDialTone] PBX. [0] Disable = Call isn't released. [1] Enable = Call is released if dial tone is detected on the device's FXO port (default).
Page 196: Configuring The Management Settings
MediaPack Series 3.5.1.1 Configuring the Management Settings The 'Management Settings' page allows you to configure the device's management parameters. To configure the Management parameters, take these 4 steps: Open the 'Management Settings' page (Management tab > Management Configuration menu > Management Settings page item). Figure 3-89: Management Settings Page Configure the Management Settings according to the table below.
Page 197: Table 3-51: Management Settings Parameters
SIP User's Manual 3. Web-Based Management Table 3-51: Management Settings Parameters Parameter Description Syslog Settings Syslog Server IP Address IP address (in dotted-decimal notation) of the computer you are using [SyslogServerIP] to run the Syslog server. The Syslog server is an application designed to collect the logs and error messages generated by the device.
Page 198 MediaPack Series Parameter Description Trap Manager Host Name Defines an FQDN of a remote host that is used as an SNMP [SNMPTrapManagerHostNa manager. The resolved IP address replaces the last entry in the Trap Manager table (defined by the parameter SNMPManagerTableIP_x) and the last trap manager entry of snmpTargetAddrTable in the snmpTargetMIB.
Page 199: Table 3-52: Snmp Trap Destinations Parameters Description
SIP User's Manual 3. Web-Based Management In the 'SNMP Trap Destinations' field, click the right-pointing arrow button; the 'SNMP Trap Destinations' page appears. Figure 3-90: SNMP Trap Destinations Page Configure the SNMP trap managers parameters according to the table below. Click the Submit button to save your changes.
Page 200: Table 3-53: Snmp Community Strings Parameters Description
MediaPack Series 3.5.1.1.2 Configuring the SNMP Community Strings The 'SNMP Community String' page allows you to configure up to five read-only and up to five read-write SNMP community strings, and to configure the community string that is used for sending traps. For detailed information on SNMP community strings, refer to the Product Reference Manual.
Page 201: Table 3-54: Snmp V3 Users Parameters
SIP User's Manual 3. Web-Based Management 3.5.1.1.3 Configuring SNMP V3 Users The 'SNMP V3 Settings' page allows you to configure authentication and privacy for up to 10 SNMP v3 users. To configure the SNMP v3 users, take the following 6 steps: Access the 'Management Settings' page, as described in ''Configuring the Management Settings'' on page 196.
Page 202: Figure 3-93: Snmp Trusted Managers
MediaPack Series Parameter Description PrivProtocol Privacy protocol of the SNMP v3 user. [SNMPUsers_PrivProtocol] 0 = none (default) 1 = DES 2 = 3DES 3 = AES128 4 = AES192 5 = AES256 AuthKey Authentication key. Keys can be entered in the form of a text password [SNMPUsers_AuthKey] or long hex string.
Page 203: Configuring The Regional Settings
SIP User's Manual 3. Web-Based Management Select the check box corresponding to the SNMP Trusted Manager that you want to enable and for whom you want to define an IP address. Define an IP address in dotted-decimal notation. Click the Submit button to apply your changes. To save the changes, refer to ''Saving Configuration'' on page 207.
Page 204: Maintenance Actions
MediaPack Series 3.5.1.3 Maintenance Actions The 'Maintenance Actions' page allows you to perform the following operations: Reset the device (refer to ''Resetting the Device'' on page 204) Lock and unlock the device (refer to ''Locking and Unlocking the Device'' on page 206) Save the configuration to the device's flash memory (refer to ''Saving Configuration'' on page 207) To access the 'Maintenance Actions' page, take this step:...
Page 205: Figure 3-96: Reset Confirmation Message Box
SIP User's Manual 3. Web-Based Management Under the 'Reset Configuration' group, from the 'Graceful Option' drop-down list, select one of the following options: • 'Yes': Reset starts only after the user-defined time in the 'Shutdown Timeout' field (refer to Step 4) expires or after no more active traffic exists (the earliest thereof). In addition, no new traffic is accepted.
Page 206: Figure 3-97: Device Lock Confirmation Message Box
MediaPack Series 3.5.1.3.2 Locking and Unlocking the Device The Lock and Unlock options allow you to lock the device so that it doesn't accept any new incoming calls. This is useful when, for example, you are uploading new software files to the device and you don't want any traffic to interfere with the process.
Page 207: Saving Configuration
SIP User's Manual 3. Web-Based Management 3.5.1.3.3 Saving Configuration The 'Maintenance Actions' page allows you to save (burn) the current parameter configuration (including loaded auxiliary files) to the device's non-volatile memory (i.e., flash). The parameter modifications that you make throughout the Web interface's pages are temporarily saved (to the volatile memory - RAM) when you click the Submit button on these pages.
Page 208: Software Update
MediaPack Series 3.5.2 Software Update The Software Update menu allows you to upgrade the device's software by loading a new cmp file (compressed firmware) along with the ini file and a suite of auxiliary files, or to update existing auxiliary files. The Software Update menu includes the following page items: Load Auxiliary Files (refer to ''Loading Auxiliary Files'' on page 208) Software Upgrade Wizard (refer to ''Software Upgrade Wizard'' on page 210)
Page 209: Figure 3-98: Load Auxiliary Files
SIP User's Manual 3. Web-Based Management To load an auxiliary file to the device using the Web interface, take these 6 steps: Open the 'Load Auxiliary Files' page (Management tab > Software Update menu > Load Auxiliary Files page item). Figure 3-98: Load Auxiliary Files Page Click the Browse button corresponding to the file type that you want to load, navigate to the folder in which the file is located, and then click Open;...
Page 210: Software Upgrade Wizard
MediaPack Series To load the auxiliary files via the ini file, take these 3 steps: In the ini file, define the auxiliary files to be loaded to the device. You can also define in the ini file whether the loaded files must be stored in the non-volatile memory so that the TFTP process is not required every time the device boots up.
Page 211: Figure 3-99: Start Software Upgrade Wizard Screen
SIP User's Manual 3. Web-Based Management To use the Software Upgrade Wizard, take these 11 steps: Stop all traffic on the device (refer to the note above). Open the 'Software Upgrade Wizard' (Management tab > Software Update menu > Software Upgrade Wizard); the 'Software Upgrade Wizard' page appears. Figure 3-99: Start Software Upgrade Wizard Screen Click the Start Software Upgrade button;...
Page 212: Figure 3-101: Cmp File Successfully Loaded To Device
MediaPack Series Note: At this stage, you can quit the Software Update Wizard, by clicking Cancel , without requiring a device reset. However, once you start uploading a cmp file, the process must be completed with a device reset. Click the Browse button, navigate to the cmp file, and then click Send File; the cmp file is loaded to the device and you're notified as to a successful loading, as shown below.
Page 213: Figure 3-102: Load An Ini File
SIP User's Manual 3. Web-Based Management In the 'Load an ini File' page, you can now choose to either: • Click Browse, navigate to the ini file, and then click Send File; the ini file is loaded to the device and you're notified as to a successful loading. •...
Page 214: Backing Up And Restoring Configuration
MediaPack Series In the 'FINISH' page, complete the upgrade process by clicking Reset; the device 'burns' the newly loaded files to flash memory and then resets t.he device. After the device resets, the 'End Process' screen appears displaying the burned configuration files (refer to the figure below).
Page 215: Figure 3-105: Configuration File
SIP User's Manual 3. Web-Based Management To save and restore the ini file, take these 3 steps: Open the 'Configuration File' page (Management tab > Software Update menu > Configuration File). Figure 3-105: Configuration File Page To save the ini file to a PC, perform the following: Click the Save INI File button;...
Page 216: Status & Diagnostics Tab
The 'Message Log' page displays Syslog debug messages sent by the device. You can select the Syslog messages in this page, and then copy and paste them into a text editor such as Notepad. This text file (txt) can then be sent to AudioCodes Technical Support for diagnosis and troubleshooting.
Page 217: Viewing The Ethernet Port Information
SIP User's Manual 3. Web-Based Management Figure 3-106: Message Log Screen The displayed logged messages are color coded as follows: • Yellow - fatal error message • Blue - recoverable error message (i.e., non-fatal error) • Black - notice message To clear the page of Syslog messages, in the Navigation tree, click the page item Message Log again;...
Page 218: Viewing Device Information
The 'Device Information' page displays the device's specific hardware and software product information. This information can help you to expedite troubleshooting. Capture the page and e-mail it to AudioCodes Technical Support personnel to ensure quick diagnosis and effective corrective action. This page also displays any loaded files used by the device (stored in the RAM) and allows you to remove them.
Page 219: Viewing Active Alarms
SIP User's Manual 3. Web-Based Management To view performance statistics, take the following step: Open the 'Performance Statistics’ page (Status & Diagnostics tab > Status & Diagnostics menu > Performance Statistics page item). Figure 3-109: Performance Statistics Page To reset the performance statistics to zero, take the following step: Click the Reset Statistics button.
Page 220: Gateway Statistics
MediaPack Series 3.6.2 Gateway Statistics The 'Gateway Statistics' page allows you to monitor real-time activity such as IP connectivity information, call details and call statistics, including the number of call attempts, failed calls, fax calls, etc. This menu includes the following page items: IP to Tel Calls Count and Tel to IP Calls Count (refer to ''Call Counters'' on page 220) Call Routing Status (refer to ''Call Routing Status'' on page 222) Registration Status (refer to "Registration Status"...
Page 221: Table 3-57: Call Counters Description
SIP User's Manual 3. Web-Based Management Table 3-57: Call Counters Description Counter Description Number of Indicates the number of attempted calls. It is composed of established and Attempted Calls failed calls. The number of established calls is represented by the 'Number of Established Calls' counter.
Page 222: Call Routing Status
MediaPack Series Counter Description Number of Failed Indicates the number of calls that failed due to unavailable resources or a Calls due to No device lock. The counter is incremented as a result of one of the following Resources release reasons: GWAPP_RESOURCE_UNAVAILABLE_UNSPECIFIED RELEASE_BECAUSE_GW_LOCKED Number of Failed...
Page 223: Registration Status
SIP User's Manual 3. Web-Based Management 3.6.2.3 Registration Status The 'Registration Status' page displays whether the device or endpoints are registered to a SIP Registrar/Proxy server. To view endpoint Registration status, take this step: Open the 'Registration Status' page (Status & Diagnostics tab > Gateway Statistics menu >...
Page 224: Sas/Sbc Registered Users
MediaPack Series 3.6.2.4 SAS/SBC Registered Users The 'SAS Registered Users' page displays a list of up to 40 Stand Alone Survivability (SAS) registered users. The SAS feature is configured in the 'SAS Configuration' page (refer to ''Stand-Alone Survivability'' on page 145). To view the SAS registered users, take this step: Open the 'SAS Registered Users' page (Status &...
Page 225: Ip Connectivity
SIP User's Manual 3. Web-Based Management 3.6.2.5 IP Connectivity The 'IP Connectivity' page displays online, read-only network diagnostic connectivity information on all destination IP addresses configured in the 'Tel to IP Routing' page (refer to ''Tel to IP Routing Table'' on page 156). Notes: •...
Page 226 MediaPack Series Column Name Description Connectivity Status The status of the IP address' connectivity according to the method in the 'Connectivity Method' field. OK = Remote side responds to periodic connectivity queries. Lost = Remote side didn't respond for a short period. Fail = Remote side doesn't respond.
Page 227: Ini File Configuration
Typically, it is loaded to or retrieved from the device using TFTP or HTTP. These protocols are not secure and vulnerable to potential hackers. To overcome this security threat, the AudioCodes' TrunkPack Downloadable Conversion Utility (DConvert) allows you to binary-encode the ini file before loading it to the device (refer to the Product Reference Manual).
Page 228: The Ini File Structure
MediaPack Series The ini File Structure The ini file can contain any number of parameters. The ini file can contain the following types of parameters: Individual parameters, which are conveniently grouped (optional) by their functionality (refer to ''Structure of Individual ini File Parameters'' on page 228) Table parameters, which include multiple individual parameters (refer to ''Structure of ini File Table Parameters'' on page 229) 4.2.1...
Page 229: Structure Of Ini File Table Parameters
SIP User's Manual 4. ini File Configuration An example of an ini file containing individual ini file parameters is shown below: [SYSTEM Params] SyslogServerIP = 10.13.2.69 EnableSyslog = 1 ; These are a few of the system-related parameters. [WEB Params] LogoWidth = '339' WebLogoText = 'My Device' UseWeblogo = 1...
Page 230 MediaPack Series Data line(s): Contain the actual values of the parameters. The values are interpreted according to the Format line. • The first word of the Data line must be the table’s string name followed by the Index field. • Items must be separated by a comma (,).
Page 231: Example Of An Ini File
SIP User's Manual 4. ini File Configuration The table below displays an example of an ini file table parameter: [ PREFIX ] FORMAT PREFIX_Index = PREFIX_DestinationPrefix, PREFIX_DestAddress, PREFIX_SourcePrefix, PREFIX_ProfileId, PREFIX_MeteringCode, PREFIX_DestPort; PREFIX 0 = 10, 10.13.83.5, *, 0, 255, 0; PREFIX 1 = 20, 10.13.83.7, *, 0, 255, 0;...
Page 232: Reference For Ini File Parameters
MediaPack Series Reference for ini File Parameters This subsection lists all the ini file parameters. References to their descriptions in the Web interface are provided except for those ini file parameters that can only be configured using the ini file. 4.4.1 Networking Parameters Table 4-1: Networking Parameters...
Page 233 SIP User's Manual 4. ini File Configuration ini File Parameter Description DNS2IP This ini file table parameter configures the internal DNS table for resolving host names to IP addresses. Two different IP addresses (in dotted-decimal notation) can be assigned to a host name. The format of this parameter is as follows: [Dns2Ip] FORMAT Dns2Ip_Index = Dns2Ip_DomainName,...
Page 234 MediaPack Series ini File Parameter Description [\SRV2IP] Notes: If the Internal SRV table is used, the device first attempts to resolve a domain name using this table. If the domain name isn't located, the device performs an SRV resolution using an external DNS server. This parameter can include up to 10 indices.
Page 235 SIP User's Manual 4. ini File Configuration ini File Parameter Description [0] = Disable UDP port translation (default). EnableUDPPortTranslatio [1] = Enable UDP port translation. When enabled, the device compares the source UDP port of the first incoming packet, to the remote UDP port stated in the opening of the channel.
Page 236 MediaPack Series ini File Parameter Description SyslogOutputMethod Determines the method used for Syslog messages. [0] = Send all Syslog messages to the defined Syslog server (default). [1] = Send all Syslog messages using the Debug Recording mechanism. [2] = Send only Error and Warning level Syslog messages using the Debug Recording mechanism.
Page 237 SIP User's Manual 4. ini File Configuration ini File Parameter Description VLANNativeVLANID For a description of this parameter, refer to ''Configuring the IP Settings'' on page 52. VLANOamVLANID For a description of this parameter, refer to ''Configuring the IP Settings'' on page 52.
Page 238 MediaPack Series ini File Parameter Description LocalControlSubnetMask For a description of this parameter, refer to ''Configuring the IP Settings'' on page 52. For a description of this parameter, refer to ''Configuring the IP Settings'' LocalControlDefaultGW on page 52. LocalOAMIPAddress For a description of this parameter, refer to ''Configuring the IP Settings'' on page 52.
Page 239 SIP User's Manual 4. ini File Configuration ini File Parameter Description GoldServiceClassDiffSer For a description of this parameter, refer to ''Configuring the QoS Settings'' on page 65. BronzeServiceClassDiffS For a description of this parameter, refer to ''Configuring the QoS Settings'' on page 65. NFS Table Parameter (NFSServers) This ini file table parameter defines Network File Systems (NFS) so that the device can access a remote server's shared files and directories for...
Page 240: System Parameters
MediaPack Series 4.4.2 System Parameters Table 4-2: System Parameters ini File Parameter Description Checks the correct functionality of the different hardware components on EnableDiagnostics the device. On completion of the check, if the test fails, the device sends information on the test results of each hardware component to the Syslog server.
Page 241 SIP User's Manual 4. ini File Configuration ini File Parameter Description (2) 'General Security Settings' (3) 'Configuration File' (4) 'IPSec/IKE' tables (5) 'Software Upgrade Key' (6) 'Internal Firewall' (7) 'Web Access List' (8) 'Web User Accounts' [NAA] (Non Authorized Access) = Attempt to access the Web interface with a false / empty user name or password.
Page 242 MediaPack Series ini File Parameter Description RAIHighThreshold High threshold percentage of total calls that are active (busy endpoints). When the percentage of the device's busy endpoints exceeds this High Threshold, the device sends the SNMP acBoardCallResourcesAlarm Alarm Trap with a 'major' Alarm Status. The range is 0 to 100.
Page 243 SIP User's Manual 4. ini File Configuration ini File Parameter Description IniFileURL Specifies the name of the ini file and the location of the server (IP address or FQDN) from which the device loads the ini file. The ini file can be loaded using: HTTP, HTTPS, FTP, FTPS or NFS.
Page 244 MediaPack Series ini File Parameter Description ResetNow Invokes an immediate restart of the device. This option can be used to activate offline (i.e., not on-the-fly) parameters that are loaded via IniFileUrl. [0] = The immediate restart mechanism is disabled (default). [1] = The device immediately restarts after an ini file with this parameter set to 1 is loaded.
Page 245 SIP User's Manual 4. ini File Configuration ini File Parameter Description [0] = Disable (default). ExtBootPReqEnable [1] = Enable extended information to be sent in BootP request. If enabled, the device uses the vendor specific information field in the BootP request to provide device-related initial startup information such as blade type, current IP address, software version, etc.
Page 246: Web And Telnet Parameters
MediaPack Series 4.4.3 Web and Telnet Parameters Table 4-3: Web and Telnet Parameters ini File Parameter Description Defines up to ten IP addresses that are permitted to access the device's WebAccessList_x Web interface and Telnet interfaces. Access from an undefined IP address is denied.
Page 247 SIP User's Manual 4. ini File Configuration ini File Parameter Description DisableWebConfig Determines whether the entire Web interface is in read-only mode. [0] = Enables modifications of parameters (default). [1] = Web interface in read-only mode. When in read-only mode, parameters can't be modified. In addition, the following pages can't be accessed: 'Web User Accounts', 'Certificates', 'Regional Settings', 'Maintenance Actions' and all file-loading pages ('Load Auxiliary Files', 'Software Upgrade Wizard', and 'Configuration...
Page 248: Security Parameters
Name of the image file (of type GIF, JPEG, or JPG) containing the user's logo. File name can be up to 47 characters. The logo file name can be used to replace AudioCodes' default Web logo with a user defined logo. 4.4.4...
Page 249 SIP User's Manual 4. ini File Configuration ini File Parameter Description PeerHostNameVerificati Determines whether the device verifies the Subject Name of a remote onMode certificate when establishing TLS connections. [0] = Disable (default). [1] = Verify Subject Name only when acting as a server for the TLS connection.
Page 250 MediaPack Series ini File Parameter Description EnableSecureStartup Enables the Secure Startup mode. In this mode, downloading the *.ini file to the device is restricted to a URL provided in initial configuration (see parameter IniFileURL) or using DHCP. [0] Disable (default). [1] Enable = disables TFTP and allows secure protocols such as HTTPS to fetch the device configuration.
Page 251 SIP User's Manual 4. ini File Configuration ini File Parameter Description is re-negotiated. PolicyLifeInKB = Lifetime (in kilobytes) that the SA negotiated in the second IKE session (quick mode) is valid. After this size is reached, the SA is re-negotiated. PolicyProposalEncryption_X = Encryption type used in the quick mode negotiation for up to four proposals (X depicts the proposal number 0 to 3): [0] No encryption, [1] DES-CBC, [2] Triple DES-CBC, [3] AES-CBC.
Page 252 MediaPack Series ini File Parameter Description IKE Parameters This ini file table parameter configures the IKE table. The format of this IPSec_IKEDB_Table parameter is as follows: [IPSec_IKEDB_Table] Format IKE_DB_INDEX = IKEPolicySharedKey, IKEPolicyProposalEncryption_X, IKEPolicyProposalAuthentication_X, IKEPolicyProposalDHGroup_X, IKEPolicyLifeInSec, IKEPolicyLifeInKB, IkePolicyAuthenticationMethod; [\IPSEC_IKEDB_TABLE] Where, SharedKey = Pre-shared key (in textual format). ProposalEncryption_X = Encryption type for up to four proposals (0 to 3): [1] DES-CBC, [2] Triple DES-CBC, [3] AES-CBC.
Page 253 SIP User's Manual 4. ini File Configuration ini File Parameter Description Secure Hypertext Transport Protocol (HTTPS) Parameters HTTPSOnly For a description of this parameter, refer to ''Configuring the General Security Settings'' on page 89. Determines the local Secured HTTPS port of the device. HTTPSPort The valid range is 1 to 65535 (other restrictions may apply within this range).
Page 254 MediaPack Series ini File Parameter Description Internal Firewall Parameters This ini file table parameter configures the device's access list (firewall), which defines network traffic filtering rules. The format of this parameter is as follows: [ACCESSLIST] FORMAT AccessList_Index = AccessList_Source_IP, AccessList_Net_Mask, AccessList_Start_Port, AccessList_End_Port, AccessList_Protocol, AccessList_Packet_Size, AccessList_Byte_Rate, AccessList_Byte_Burst, AccessList_Allow_Type;...
Page 255: Radius Parameters
SIP User's Manual 4. ini File Configuration 4.4.5 RADIUS Parameters For detailed information on the supported RADIUS attributes, refer to ''Supported RADIUS Attributes'' on page 334. Table 4-5: RADIUS Parameters ini File Parameter Description EnableRADIUS For a description of this parameter, refer to ''Configuring the General Security Settings'' on page 89.
Page 256: Snmp Parameters
MediaPack Series 4.4.6 SNMP Parameters Table 4-6: SNMP Parameters ini File Parameter Description For a description of this parameter, refer to ''Configuring the DisableSNMP Management Settings'' on page 196. SNMPPort The device's local UDP port used for SNMP Get/Set commands. The range is 100 to 3999.
Page 257 SIP User's Manual 4. ini File Configuration ini File Parameter Description SNMPManagerTrapSendingEn For a description of this parameter, refer to ''Configuring the SNMP able_x Managers Table'' on page 198. SNMPTrapManagerHostName For a description of this parameter, refer to ''Configuring the Management Settings'' on page 196.
Page 258: Sip Configuration Parameters
MediaPack Series 4.4.7 SIP Configuration Parameters Table 4-7: SIP Parameters ini File Parameter Description For a description of this parameter, refer to ''SIP General Parameters'' SIPTransportType on page 100. TCPLocalSIPPort For a description of this parameter, refer to ''SIP General Parameters'' on page 100.
Page 259 SIP User's Manual 4. ini File Configuration ini File Parameter Description ProxyIP This ini file table parameter configures the Proxy Set ID table for configuring up to six Proxy Sets, each with up to five Proxy server IP addresses. The format of this parameter is as follows: [ProxyIP] FORMAT ProxyIp_Index = ProxyIp_IpAddress, ProxyIp_TransportType, ProxyIp_ProxySetId;...
Page 260 MediaPack Series ini File Parameter Description ProxySet This ini file table parameter configures the Proxy Set table by assigning various attributes per Proxy Set ID. The format of this parameter is as follows: [ProxySet] FORMAT ProxySet_Index = ProxySet_EnableProxyKeepAlive, ProxySet_ProxyKeepAliveTime, ProxySet_ProxyLoadBalancingMethod, ProxySet_IsProxyHotSwap; [\ProxySet] For example: [ProxySet]...
Page 261 SIP User's Manual 4. ini File Configuration ini File Parameter Description SourceNumberPreference Determines the SIP header used to determine the Source Number in incoming INVITE messages. “” (empty string) = Use device's internal logic for header preference (default). “FROM” = Use the Source Number received in the From header. The valid range is a string of up to 10 characters.
Page 262 MediaPack Series ini File Parameter Description Password For a description of this parameter, refer to ''Proxy & Registration Parameters'' on page 110. For a description of this parameter, refer to ''Proxy & Registration Cnonce Parameters'' on page 110. SIPChallengeCachingMod For a description of this parameter, refer to ''Proxy & Registration Parameters'' on page 110.
Page 263 SIP User's Manual 4. ini File Configuration ini File Parameter Description ForkingHandlingMode Determines how the device reacts to forking of outgoing INVITE messages by the Proxy. [0] = Sequential. The device opens a voice stream toward the first 18x SIP response that includes an SDP, and disregards any 18x response with an SDP received thereafter (default).
Page 264 MediaPack Series ini File Parameter Description You can define multiple table indices having the same ServedTrunkGroup with different ServingIPGroups, username, password, and other parameters. This provides the capability for registering the same Hunt Group to several ITSP's (i.e., Serving IP Groups).
Page 265 SIP User's Manual 4. ini File Configuration ini File Parameter Description NumberOfActiveDialogs Defines the maximum number of active SIP dialogs that are not call related (i.e., REGISTER and SUBSCRIBE). This parameter is used to control the Registration / Subscription rate. The valid range is 1 to 5.
Page 266 MediaPack Series ini File Parameter Description EnableUserInfoUsage For a description of this parameter, refer to ''Advanced Parameters'' on page 127. Determines whether the device uses the value of the incoming SIP HandleReasonHeader Reason header for Release Reason mapping. [0] Disregard Reason header in incoming SIP messages. [1] Use the Reason header value for Release Reason mapping (default).
Page 267 SIP User's Manual 4. ini File Configuration ini File Parameter Description SipT1Rtx For a description of this parameter, refer to ''SIP General Parameters'' on page 100. SipT2Rtx For a description of this parameter, refer to ''SIP General Parameters'' on page 100. EnableEarlyMedia For a description of this parameter, refer to ''SIP General Parameters'' on page 100.
Page 268 MediaPack Series ini File Parameter Description The EnableHold parameter must be enabled on both the calling and the called sides. To define call waiting using the Web interface, refer to "Call Waiting" on page 355. For a description on using ini file table parameters, refer to Structure of ini File Table Parameters on page 229.
Page 269 SIP User's Manual 4. ini File Configuration ini File Parameter Description FirstCallWaitingToneID Determines the index of the first Call Waiting Tone in the CPT file. This feature enables the called party to distinguish between four different call origins (e.g., external vs. internal calls). The device plays the tone received in the 'play tone CallWaitingTone#' parameter of an INFO message + the value of this parameter - 1.
Page 270 MediaPack Series ini File Parameter Description ''Structure of ini File Table Parameters'' on page 229. DisableAutoDTMFMute Enables / disables the automatic muting of DTMF digits when out-of- band DTMF transmission is used. [0] = Automatic mute is used (default). [1] = No automatic mute of in-band DTMF. When DisableAutoDTMFMute = 1, the DTMF transport type is set according to the parameter DTMFTransportType and the DTMF digits aren't muted if out-of-band DTMF mode is selected (TxDTMFOption =1,...
Page 271 SIP User's Manual 4. ini File Configuration ini File Parameter Description Authentication This ini file table parameter defines a username and password combination for authenticating each device port. The format of this parameter is as follows: [Authentication] FORMAT Authentication_Index = Authentication_UserId, Authentication_UserPassword, Authentication_Port, Authentication_Module;...
Page 272 MediaPack Series ini File Parameter Description SASLocalSIPTLSPort For a description of this parameter, refer to "Stand-Alone Survivability" on page 145. Profile Parameters CoderName This ini file table parameter defines the device's coder list. This includes up to five groups of coders (consisting of up to five coders per group) that can be associated with IP or Tel profiles ('Coder Group Settings' page in the Web interface -- refer to ''Coder Group Settings'' on page 166).
Page 273 SIP User's Manual 4. ini File Configuration ini File Parameter Description IPProfile This ini file table parameter configures the IP profiles table. The format of this parameter is as follows: [IPProfile] FORMAT IPProfile_Index = IPProfile_ProfileName, IPProfile_IpPreference, IPProfile_CodersGroupID, IPProfile_IsFaxUsed*, IPProfile_JitterBufMinDelay*, IPProfile_JitterBufOptFactor*, IPProfile_IPDiffServ*, IPProfile_SigIPDiffServ*, N/A, IPProfile_RTPRedundancyDepth, IPProfile_RemoteBaseUDPPort, IPProfile_CNGmode, IPProfile_VxxTransportType, IPProfile_NSEMode, N/A,...
Page 274 MediaPack Series ini File Parameter Description TelProfile This ini file table parameter configures the Tel Profile Settings table. The format of this parameter is as follows: [TelProfile] FORMAT TelProfile_Index = TelProfile_ProfileName, TelProfile_TelPreference, TelProfile_CodersGroupID, TelProfile_IsFaxUsed*, TelProfile_JitterBufMinDelay*, TelProfile_JitterBufOptFactor*, TelProfile_IPDiffServ*, TelProfile_SigIPDiffServ*, TelProfile_DtmfVolume, TelProfile_InputGain, TelProfile_VoiceVolume, TelProfile_EnableReversePolarity, TelProfile_EnableCurrentDisconnect, TelProfile_EnableDigitDelivery, TelProfile_EnableEC, TelProfile_MWIAnalog, TelProfile_MWIDisplay,...
Page 275: Voice Mail Parameters
SIP User's Manual 4. ini File Configuration 4.4.8 Voice Mail Parameters For detailed information on the Voice Mail application, refer to the CPE Configuration Guide for Voice Mail. Table 4-8: Voice Mail Parameters ini File Parameter Description VoiceMailInterface For a description of this parameter, refer to ''Configuring the Voice Mail (VM) Parameters'' on page 187.
Page 276: Pstn Parameters
MediaPack Series ini File Parameter Description DigitPatternExternalCall For a description of this parameter, refer to ''Configuring the Voice Mail (VM) Parameters'' on page 187. For a description of this parameter, refer to ''Configuring the Voice Mail TelDisconnectCode (VM) Parameters'' on page 187. DigitPatternDigitToIgnore For a description of this parameter, refer to ''Configuring the Voice Mail (VM) Parameters'' on page 187.
Page 277: 4.4.10 Analog Telephony Parameters
SIP User's Manual 4. ini File Configuration 4.4.10 Analog Telephony Parameters Table 4-10: Analog Telephony Parameters ini File Parameter Description Prefix2ExtLine Defines a string prefix (e.g., '9') that when dialed from an FXS port causes the device's FXS port to play a secondary dial tone and then restart digit collection.
Page 278 MediaPack Series ini File Parameter Description [ChargeCode] ChargeCode 1 = 7,30,1,14,20,2,20,15,1,0,60,1; ChargeCode 2 = 5,60,1,14,20,1,0,60,1; ChargeCode 3 = 0,60,1; ChargeCode 0 = 6, 3, 1, 12, 2, 1, 18, 5, 2, 0, 2, 1; [\ChargeCode] Notes: The parameter can appear up to 25 times (i.e., up to 25 different metering rules can be defined).
Page 279 SIP User's Manual 4. ini File Configuration ini File Parameter Description CallerDisplayInfo This ini file table parameter enables the device to send Caller ID information to IP when a call is made. The format of this parameter is as follows: [CallerDisplayInfo] FORMAT CallerDisplayInfo_Index = CallerDisplayInfo_DisplayString, CallerDisplayInfo_IsCidRestricted, CallerDisplayInfo_Port,...
Page 280 MediaPack Series ini File Parameter Description Notes: The indexing of this parameter starts at 1. The device ports starts at 0. This parameter can appear up to 24 times for MP-124. To configure the Call Forward table using the Web interface, refer to ''Call Forward'' on page 175.
Page 281 SIP User's Manual 4. ini File Configuration ini File Parameter Description FXSOOSBehavior For a description of this parameter, refer to ''Advanced Parameters'' on page 127. NumberOfWaitingIndicat For a description of this parameter, refer to ''Supplementary Services'' on ions page 135. TimeBetweenWaitingIndi For a description of this parameter, refer to ''Supplementary Services'' on cations...
Page 282 MediaPack Series ini File Parameter Description KeyCFBusyOrNoAnswer For a description of this parameter, refer to ''Keypad Features'' on page 142. For a description of this parameter, refer to ''Keypad Features'' on page KeyCFDoNotDisturb 142. KeyCFDeact For a description of this parameter, refer to ''Keypad Features'' on page 142.
Page 283 SIP User's Manual 4. ini File Configuration ini File Parameter Description Notes: This parameter is applicable only to FXS interfaces. This parameter is per device. This parameter can appear up to 8 times for 8-port MP-11x devices and up to 24 times for MP-124 devices. The double dollar ($$) symbol represents the default value.
Page 284 MediaPack Series ini File Parameter Description Notes: This parameter is applicable only to FXS interfaces. For an explanation on using ini file table parameters, refer to ''Structure of ini File Table Parameters'' on page 229. EnableCallerIDTypeTwo Disables the generation of Caller ID type 2 when the phone is off-hooked. Caller ID type 2, also known as off-hook Caller ID is sent to a currently busy telephone to display the caller ID of the waiting call.
Page 285 SIP User's Manual 4. ini File Configuration ini File Parameter Description ETSICallerIDTypeOneSu Selects the ETSI FSK Caller ID Type 1 sub-standard (FXS only). bStandard [0] = ETSI between rings (default). [1] = ETSI before ring DT_AS. [2] = ETSI before ring RP_AS. [3] = ETSI before ring LR_DT_AS.
Page 286: 4.4.11 Number Manipulation And Routing Parameters
MediaPack Series 4.4.11 Number Manipulation and Routing Parameters Table 4-11: Number Manipulation and Routing Parameters ini File Parameter Description This ini file table parameter defines the device's endpoints. Alternatively, TrunkGroup you can use the Web interface (refer to "Configuring the Endpoint Phone Numbers"...
Page 287 ServingIPGroup = Serving IP Group ID to where INVITE messages initiated by the Hunt Group endpoints are sent. For example: [TrunkGroupSettings] TrunkGroupSettings 0 = 1, 0, 5, audiocodes, user, 1; TrunkGroupSettings 1 = 2, 1, 0, localname, user1, 2; [\TrunkGroupSettings] Notes: This parameter can include up to 24 indices.
Page 288 MediaPack Series ini File Parameter Description Prefix This ini file table parameter configures the 'Tel to IP Routing' table for routing Tel-to-IP calls (i.e., to a destination IP address). The format of this parameter is as follows: [PREFIX] FORMAT PREFIX_Index = PREFIX_DestinationPrefix, PREFIX_DestAddress, PREFIX_SourcePrefix, PREFIX_ProfileId, PREFIX_MeteringCode, PREFIX_SrcIPGroupID, PREFIX_DestHostPrefix, PREFIX_DestIPGroupID,...
Page 289 SIP User's Manual 4. ini File Configuration ini File Parameter Description between 10.8.8.10 to 10.8.8.99. The '*' wildcard represents any number between 0 and 255, e.g., 10.8.8.* represents all addresses between 10.8.8.0 and 10.8.8.255. If the string 'ENUM' is specified for the destination IP address, an ENUM query containing the destination phone number is sent to the DNS server.
Page 290 MediaPack Series ini File Parameter Description To support the In-Call Alternative Routing feature, you can use two entries that support the same call, but assigned with a different HuntGroup. The second entry functions as an alternative selection if the first rule fails as a result of one of the release reasons listed in the AltRouteCauseIP2Tel table.
Page 291 SIP User's Manual 4. ini File Configuration ini File Parameter Description SourcePrefix = Source number prefix. SourceAddress = N/A. NumberType = Number Type used in RPID header. NumberPlan = Number Type used in RPID header. RemoveFromLeft = Number of stripped digits from the left. RemoveFromRight = Number of stripped digits from the right.
Page 292 MediaPack Series ini File Parameter Description SourceAddress = Source IP address (obtained from the Contact header in the INVITE message). NumberType = N/A (set to $$). NumberPlan = N/A (set to $$). RemoveFromLeft = Number of stripped digits from the left. RemoveFromRight = Number of stripped digits from the right.
Page 293 SIP User's Manual 4. ini File Configuration ini File Parameter Description [\SourceNumberMapTel2Ip] Where, DestinationPrefix = Destination number prefix. SourcePrefix = Source number prefix. SourceAddress = Source IP address (obtained from the Request- URI in the INVITE message). NumberType = Number Type used in RPID header. NumberPlan = Number Plan used in RPID header.
Page 294 MediaPack Series ini File Parameter Description SourceNumberMapIP2Tel This ini file table parameter manipulates the source number for IP-to-Tel calls. The format of this parameter is as follows: [SourceNumberMapIp2Tel] FORMAT SourceNumberMapIp2Tel_Index = SourceNumberMapIp2Tel_DestinationPrefix, SourceNumberMapIp2Tel_SourcePrefix, SourceNumberMapIp2Tel_SourceAddress, SourceNumberMapIp2Tel_NumberType, SourceNumberMapIp2Tel_NumberPlan, SourceNumberMapIp2Tel_RemoveFromLeft, SourceNumberMapIp2Tel_RemoveFromRight, SourceNumberMapIp2Tel_LeaveFromRight, SourceNumberMapIp2Tel_Prefix2Add, SourceNumberMapIp2Tel_Suffix2Add, SourceNumberMapIp2Tel_IsPresentationRestricted;...
Page 295 SIP User's Manual 4. ini File Configuration ini File Parameter Description To configure manipulation of source numbers for IP-to-Tel calls using the Web interface (i.e., in the 'Source Phone Number Manipulation Table for IP-to-Tel Calls' table), refer to ''Configuring the Number Manipulation Tables'' on page 148). For a description on using ini file table parameters, refer to ''Structure of ini File Table Parameters'' on page 229.
Page 296 MediaPack Series ini File Parameter Description AltRouteCauseIP2Tel This ini file table parameter configures call failure reason values received from the TelPSTN side . If a call is released as a result of one of these reasons, the device attempts to locate an alternative Hunt Group for the call in the 'IP to Hunt Group Routing' table.
Page 297: 4.4.12 Channel Parameters
SIP User's Manual 4. ini File Configuration ini File Parameter Description for this parameter is as follows: [PhoneContext] FORMAT PhoneContext_Index = PhoneContext_Npi, PhoneContext_Ton, PhoneContext_Context; [\PhoneContext] Where, Npi = Number Plan. Ton = Type of Number. Context = Phone-Context value. When a call is received from the Tel, the NPI and TON are compared to the table, and the Phone-Context value is used in the outgoing SIP INVITE message.
Page 298 MediaPack Series ini File Parameter Description FaxTransportMode For a description of this parameter, refer to ''Configuring the Fax / Modem / CID Settings'' on page 70. For a description of this parameter, refer to ''Configuring the Fax / FaxRelayEnhancedRedundanc Modem / CID Settings'' on page 70. yDepth FaxRelayRedundancyDepth For a description of this parameter, refer to ''Configuring the Fax /...
Page 299 G.711 coders is a standard one (8 for G.711 A-Law and 0 for G.711 µ-Law). The parameters defining payload type for the 'old' AudioCodes' Bypass mode FaxBypassPayloadType and ModemBypassPayloadType are not used with NSE Bypass. The bypass packet interval is selected according to the parameter FaxModemBypassBasicRtpPacketInterval.
Page 300 MediaPack Series ini File Parameter Description NSEPayloadType NSE payload type for Cisco Bypass compatible mode. The valid range is 96-127. The default value is 105. Note: Cisco gateways usually use NSE payload type of 100. For a description of this parameter, refer to ''Configuring the Fax / V21ModemTransportType Modem / CID Settings'' on page 70.
Page 301 SIP User's Manual 4. ini File Configuration ini File Parameter Description TestMode Defines the type of testing mode: [0] = CoderLoopback, encoder-decoder loopback inside DSP. [1] = PCMLoopback, loopback the incoming PCM to the outgoing PCM. [2] = ToneInjection, generates a 1000-Hz tone to outgoing PCM.
Page 302: 4.4.13 Auxiliary / Configuration Files Parameters
MediaPack Series ini File Parameter Description CPTDetectorFrequencyDeviati Defines the deviation (in Hz) allowed for the detection of each CPT signal frequency. The valid range is 1 to 30. The default value is 10. [0] = DTMF event is reported on the end of a detected DTMF MGCPDTMFDetectionPoint digit.
Page 303: Default Settings
SIP User's Manual 5. Default Settings Default Settings You can restore the device's factory default settings or define your own default settings for the device. Note: You can also restore factory default settings using the device's hardware reset button (refer to the device's Fast Track Guide). Defining Default Settings The device is shipped with factory default configuration values stored on its non-volatile flash memory.
Page 304 MediaPack Series Reader's Notes SIP User's Manual Document #: LTRT-65410...
Page 305: Auxiliary Configuration Files
SIP User's Manual 6. Auxiliary Configuration Files Auxiliary Configuration Files This section describes the auxiliary files (with the dat file extension), which are loaded, in addition to the ini file, to the device. You can load the auxiliary files to the device using one of the following methods: Web interface (refer to ''Loading Auxiliary Files'' on page 208) ini file: specify the name of the relevant auxiliary file in the device's ini file and then...
Page 306 MediaPack Series You can specify several tones of the same type. These additional tones are used only for tone detection. Generation of a specific tone conforms to the first definition of the specific tone. For example, you can define an additional dial tone by appending the second dial tone's definition lines to the first tone definition in the ini file.
Page 307 SIP User's Manual 6. Auxiliary Configuration Files • Second Signal On Time [10 msec]: 'Signal On' period (in 10 msec units) for the second cadence on-off cycle. Can be omitted if there isn't a second cadence. • Second Signal Off Time [10 msec]: 'Signal Off' period (in 10 msec units) for the second cadence on-off cycle.
Page 308: Configuring The Distinctive Ringing Section Of The Ini File
MediaPack Series Configuring the Distinctive Ringing Section of the ini File Distinctive Ringing is only applicable to FXS interface. Using the distinctive ringing section of this auxiliary file, you can create up to 16 distinctive ringing patterns. Each ringing pattern configures the ringing tone frequency and up to four ringing cadences. The same ringing frequency is used for all the ringing pattern cadences.
Page 309: Examples Of Ringing Signals
SIP User's Manual 6. Auxiliary Configuration Files 6.2.1 Examples of Ringing Signals Below is an example of a ringing burst: #Three ringing bursts followed by repeated ringing of 1 sec on and 3 sec off. [NUMBER OF DISTINCTIVE RINGING PATTERNS] Number of Ringing Patterns=1 [Ringing Pattern #0] Ring Type=0...
Page 310: Coefficient File
MediaPack Series The PRT dat file contains a set of prerecorded tones to be played by the device during operation. Up to 40 tones (totaling approximately 10 minutes) can be stored in a single file in flash memory. The prerecorded tones are prepared offline using standard recording utilities (such as CoolEdit ) and combined into a single file using the TrunkPack Downloadable Conversion utility (refer to the Product Reference Manual).
Page 311: User Information File
SIP User's Manual 6. Auxiliary Configuration Files Note: To configure the FXO coefficients, use the parameter CountryCoefficients (described in Analog Telephony Parameters on page 277) . User Information File The User Information file is a text file that maps PBX extensions, connected to the device, to global IP numbers.
Page 312 MediaPack Series The User Information file can be loaded to the device using the ini file (UserInfoFileName parameter described in ''Auxiliary / Configuration Files Parameters'' on page 302), the Web interface (refer to ''Loading Auxiliary Files'' on page 208), or by using the automatic update mechanism (UserInfoFileURL, refer to the Product Reference Manual).
Page 313: Ip Telephony Capabilities
SIP User's Manual 7. IP Telephony Capabilities IP Telephony Capabilities This section describes the device's IP telephony capabilities. Configuring the DTMF Transport Types You can control the way DTMF digits are transported over the IP network to the remote endpoint, by using one of the following modes: Using INFO message according to Nortel IETF draft: DTMF digits are carried to the remote side in INFO messages.
Page 314: Fax And Modem Capabilities
MediaPack Series Note that to set the RFC 2833 payload type with a different value (other than its default, 96) configure the RFC2833PayloadType (RFC 2833 Payload Type) parameter. The device negotiates the RFC 2833 payload type using local and remote SDP and sends packets using the payload type from the received SDP.
Page 315: Fax/Modem Transport Modes
SIP User's Manual 7. IP Telephony Capabilities remote endpoint at the establishment of the call. During a call, when a fax / modem signal is detected, transition from voice to VBD (or T.38) is automatically performed and no additional SIP signaling is required. If negotiation fails (i.e., no match is achieved for any of the transport capabilities), fallback to existing logic occurs (according to the parameter IsFaxUsed).
Page 316: Fax/Modem Bypass Mode
MediaPack Series 7.2.2.1.1 Switching to T.38 Mode using SIP Re-INVITE In the Switching to T.38 Mode using SIP Re-INVITE mode, upon detection of a fax signal, the terminating device negotiates T.38 capabilities using a Re-INVITE message. If the far- end device doesn't support T.38, the fax fails. In this mode, the parameter FaxTransportMode is ignored.
Page 317: Fax / Modem Nse Mode
Tip: When the remote (non-AudioCodes’) gateway uses G711 coder for voice and doesn’t change the coder payload type for fax or modem transmission, it is recommended to use the Bypass mode with the following configuration: •...
Page 318: G.711 Fax / Modem Transport Mode
MediaPack Series The Cisco gateway must include the following definition: "modem passthrough nse payload-type 100 codec g711alaw". To configure NSE mode, perform the following configurations: IsFaxUsed = 0 FaxTransportMode = 2 NSEMode = 1 NSEPayloadType = 100 V21ModemTransportType = 2 V22ModemTransportType = 2 V23ModemTransportType = 2 V32ModemTransportType = 2...
Page 319: Fax / Modem Transparent Mode
SIP User's Manual 7. IP Telephony Capabilities Echo Canceller Non-Linear Processor Mode = off Dynamic Jitter Buffer Minimum Delay = 40 Dynamic Jitter Buffer Optimization Factor = 13 When the device initiates a fax session using G.711, a ‘gpmd’ attribute is added to the SDP according to the following format: For G.711A-law: a=gpmd:0 vbd=yes;ecan=on For G.711 µ-law: a=gpmd:8 vbd=yes;ecan=on...
Page 320: Fax / Modem Transparent With Events Mode
MediaPack Series 7.2.2.7 Fax / Modem Transparent with Events Mode In this mode, fax and modem signals are transferred using the current voice coder with the following automatic adaptations: Echo Canceller = on (or off, for modems) Echo Canceller Non-Linear Processor Mode = off Jitter buffering optimizations To configure fax / modem transparent with events mode, perform the following configurations:...
Page 321: Using Relay Mode For Both T.30 And V.34 Faxes
SIP User's Manual 7. IP Telephony Capabilities Configure the following parameters to use bypass mode for V.34 faxes and T.38 for T.30 faxes: FaxTransportMode = 1 (Relay) V34ModemTransportType = 2 (Modem bypass) V32ModemTransportType = 2 V23ModemTransportType = 2 V22ModemTransportType = 2 7.2.3.2 Using Relay mode for both T.30 and V.34 faxes In this scenario, V.34 fax machines are forced to use their backward compatibility with T.30...
Page 322: Fxo Operating Modes
MediaPack Series In the previous example, V.152 implementation is supported (using the dynamic payload type 96 and G.711 u-law as the VBD codec) as well as the voice codecs G.711 µ-law and G.729. Instead of using VBD transport mode, the V.152 implementation can use alternative relay fax transport methods (e.g., fax relay over IP using T.38).
Page 323: One-Stage Dialing
SIP User's Manual 7. IP Telephony Capabilities 7.3.1.1 One-Stage Dialing One-stage dialing is when the FXO device receives an IP-to-Tel call, off-hooks the PBX line connected to the telephone, and then immediately dials the destination telephone number. In other words, the IP caller doesn't dial the PSTN number upon hearing a dial tone.
Page 324: Two-Stage Dialing
MediaPack Series 7.3.1.2 Two-Stage Dialing Two-stage dialing is when the IP caller is required to dial twice. The caller initially dials to the FXO device and only after receiving a dial tone from the PBX (via the FXO device), dials the destination telephone number. Figure 7-2: Call Flow for Two-Stage Dialing Two-stage dialing implements the Dialing Time feature.
Page 325: Did Wink
SIP User's Manual 7. IP Telephony Capabilities Detection of Reorder, Busy, Dial, and Special Information Tone (SIT) tones: The call is immediately disconnected after a Reorder, Busy, Dial, or SIT tone is detected on the Tel side (assuming the PBX / CO generates this tone). This method requires the correct tone frequencies and cadence to be defined in the Call Progress Tones file.
Page 326: Telephone-To-Ip Calls
MediaPack Series 7.3.2 Telephone-to-IP Calls The FXO device provides the following FXO operating modes for Tel-to-IP calls: Automatic Dialing (refer to ''Automatic Dialing'' on page 326) Collecting Digits Mode (refer to ''Collecting Digits Mode'' on page 327) Ring Detection Timeout (refer to ''Ring Detection Timeout'' on page 327) FXO Supplementary Services (refer to ''FXO Supplementary Services'' on page 328) •...
Page 327: Collecting Digits Mode
SIP User's Manual 7. IP Telephony Capabilities 7.3.2.2 Collecting Digits Mode When automatic dialing is not defined, the device collects the digits. The SIP call flow diagram below illustrates the Collecting Digits Mode. Figure 7-4: Call Flow for Collecting Digits Mode 7.3.2.3 Ring Detection Timeout The ini file parameters IsWaitForDialTone and WaitForDialTone apply to Ring Detection...
Page 328: Fxo Supplementary Services
MediaPack Series 7.3.2.4 FXO Supplementary Services The FXO supplementary services include the following: Hold / Transfer toward the Tel side: The ini file parameter LineTransferMode must be set to 0 (default). If the FXO receives a hook-flash from the IP side (using out-of- band or RFC 2833), the device sends the hook-flash to the Tel side by performing one of the following: •...
Page 329 SIP User's Manual 7. IP Telephony Capabilities The X-Detect event notification process is as follows: For IP-to-Tel or Tel-to-IP calls, the device receives a SIP request message (using the X-Detect header) that the remote party wishes to detect events on the media stream. For incoming (IP-to-Tel) calls, the request must be indicated in the initial INVITE and responded to either in the 183 response (for early dialogs) or in the 200 OK response (for confirmed dialogs).
Page 330: Rtp Multiplexing (Throughpacket)
MediaPack Series RTP Multiplexing (ThroughPacket) The device supports a proprietary method to aggregate RTP streams from several channels to reduce the bandwidth overhead caused by the attached Ethernet, IP, UDP, and RTP headers, and to reduce the packet / data transmission rate. This option reduces the load on network routers and can typically save 50% (e.g., for G.723) on IP bandwidth.
Page 331: Configuring Alternative Routing (Based On Connectivity And Qos)
SIP User's Manual 7. IP Telephony Capabilities The default settings of 10 msec Minimum delay and 10 Optimization Factor should provide a good compromise between delay and error rate. The jitter buffer ‘holds’ incoming packets for 10 msec before making them available for decoding into voice. The coder polls frames from the buffer at regular intervals in order to produce continuous speech.
Page 332: Determining The Availability Of Destination Ip Addresses
MediaPack Series 7.7.2 Determining the Availability of Destination IP Addresses To determine the availability of each destination IP address (or host name) in the routing table, one (or all) of the following (configurable) methods are applied: Connectivity: The destination IP address is queried periodically (currently only by ping).
Page 333: Call Detail Record
SIP User's Manual 7. IP Telephony Capabilities Call Detail Record The Call Detail Record (CDR) contains vital statistic information on calls made by the device. CDRs are generated at the end and (optionally) at the beginning of each call (determined by the parameter CDRReportLevel), and then sent to a Syslog server. The destination IP address for CDR logs is determined by the parameter CDRSyslogServerIP.
Page 334: Supported Radius Attributes
MediaPack Series Field Name Description OutPackets Number of Outgoing Packets Local Packet Loss PackLoss RemotePackLoss Number of Outgoing Lost Packets UniqueId unique RTP ID Call Setup Time SetupTime ConnectTime Call Connect Time ReleaseTime Call Release Time RTP Delay RTPdelay RTPjitter RTP Jitter RTPssrc Local RTP SSRC...
Page 335 SIP User's Manual 7. IP Telephony Capabilities Attribute Attribute Value Purpose Example Number Name Format octets Stop Acc H323-Setup- Start Acc Setup time in NTP format 1 String Time Stop Acc The call’s originator: H323-Call- Answer, Start Acc Answering (IP) or Originator String Origin Originate etc...
Page 336: Proxy Or Registrar Registration Example
MediaPack Series Attribute Attribute Value Purpose Example Number Name Format Acct-Output- Number of packets sent Numeric Stop Acc Packets during the call NAS-Port- Physical port type of device Start Acc String Type on which the call is active Asynchronous Stop Acc Response Attributes The reason for failing H323-Return-...
Page 337 SIP User's Manual 7. IP Telephony Capabilities The ‘servername’ string is defined according to the following rules: The "servername" is equal to "RegistrarName" if configured. The "RegistrarName" can be any string. Otherwise, the "servername" is equal to "RegistrarIP" (either FQDN or numerical IP address), if configured.
Page 338: Configuration Examples
F1 (10.8.201.108 >> 10.8.201.10 INVITE): INVITE sip:1000@10.8.201.10;user=phone SIP/2.0 Via: SIP/2.0/UDP 10.8.201.108;branch=z9hG4bKacsiJkDGd From: <sip:8000@10.8.201.108>;tag=1c5354 To: <sip:1000@10.8.201.10> Call-ID: 534366556655skKw-8000--1000@10.8.201.108 CSeq: 18153 INVITE Contact: <sip:8000@10.8.201.108;user=phone> User-Agent: Audiocodes-Sip-Gateway/device/v.5.40.010.006 Supported: 100rel,em Allow: REGISTER,OPTIONS,INVITE,ACK,CANCEL,BYE, NOTIFY,PRACK,REFER,INFO Content-Type: application/sdp Content-Length: 208 o=AudiocodesGW 18132 74003 IN IP4 10.8.201.108 s=Phone-Call c=IN IP4 10.8.201.108...
Page 339 7. IP Telephony Capabilities F2 (10.8.201.10 >> 10.8.201.108 TRYING): SIP/2.0 100 Trying Via: SIP/2.0/UDP 10.8.201.108;branch=z9hG4bKacsiJkDGd From: <sip:8000@10.8.201.108>;tag=1c5354 To: <sip:1000@10.8.201.10> Call-ID: 534366556655skKw-8000--1000@10.8.201.108 Server: Audiocodes-Sip-Gateway/device/v.5.40.010.006 CSeq: 18153 INVITE Content-Length: 0 F3 (10.8.201.10 >> 10.8.201.108 180 RINGING): SIP/2.0 180 Ringing Via: SIP/2.0/UDP 10.8.201.108;branch=z9hG4bKacsiJkDGd From: <sip:8000@10.8.201.108>;tag=1c5354 To: <sip:1000@10.8.201.10>;tag=1c7345...
Page 340: 7.12.2 Sip Authentication Example
10.8.201.10. Voice path is established. F6 (10.8.201.108 >> 10.8.201.10 BYE): BYE sip:1000@10.8.201.10;user=phone SIP/2.0 Via: SIP/2.0/UDP 10.8.201.108;branch=z9hG4bKacRKCVBud From: <sip:8000@10.8.201.108>;tag=1c5354 To: <sip:1000@10.8.201.10>;tag=1c7345 Call-ID: 534366556655skKw-8000--1000@10.8.201.108 User-Agent: Audiocodes-Sip-Gateway/device/v.5.40.010.006 CSeq: 18154 BYE Supported: 100rel,em Content-Length: 0 F7 (10.8.201.10 >> 10.8.201.108 200 OK): SIP/2.0 200 OK Via: SIP/2.0/UDP 10.8.201.108;branch=z9hG4bKacRKCVBud From: <sip:8000@10.8.201.108>;tag=1c5354...
Page 341 Since the algorithm is MD5, then: • The username is equal to the endpoint phone number 122. • The realm return by the proxy is audiocodes.com. • The password from the ini file is AudioCodes. • The equation to be evaluated is (according to RFC this part is called A1) ‘122:audiocodes.com:AudioCodes’.
Page 342: 7.12.3 Establishing A Call Between Two Devices
Expires: Thu, 26 Jul 2001 10:34:42 GMT 7.12.3 Establishing a Call between Two Devices This section provides an example on configuring two AudioCodes' devices with FXS interfaces for establishing call communication. After configuration, you can make calls between telephones connected to the same device or between the two devices.
Page 343: 7.12.4 Remote Pbx Extension Between Fxo And Fxs Devices
SIP User's Manual 7. IP Telephony Capabilities For the second device (10.2.37.20), in the ‘Endpoint Phone Number Table' page, assign the phone numbers 201 to 204 to the device's endpoints. Figure 7-7: Assigning Phone Numbers to Device 10.2.37.20 Configure the following settings for both devices: In the ‘Tel to IP Routing’...
Page 344: Dialing From Remote Extension (Phone At Fxs)
MediaPack Series The following is required: One FXO device with ports connected directly to the PBX lines (shown in the figure below) One FXS device for the 'remote PBX extension' Analog phones (POTS) PBX (one or more PBX loop start lines) LAN network Figure 7-9: FXO-FXS Remote PBX Extension (Example) 7.12.4.1 Dialing from Remote Extension (Phone at FXS)
Page 345: 7.12.4.2 Dialing From Pbx Line Or Pstn
SIP User's Manual 7. IP Telephony Capabilities 7.12.4.2 Dialing from PBX Line or PSTN The procedure below describes how to dial from a PBX line (i.e., from a telephone directly connected to the PBX) or from the PSTN to the 'remote PBX extension' (i.e., telephone connected to the FXS device).
Page 346: 7.12.4.4 Call Waiting For Remote Extensions
MediaPack Series 7.12.4.4 Call Waiting for Remote Extensions When the FXO device detects a Call Waiting indication (FSK data of the Caller Id - CallerIDType2) from the PBX, it sends a proprietary INFO message, which includes the caller identification to the FXS device. Once the FXS device receives this INFO message, it plays a call waiting tone and sends the caller ID to the relevant port for display.
Page 347: Figure 7-13: Automatic Dialing For Fxs Ports
SIP User's Manual 7. IP Telephony Capabilities Figure 7-13: Automatic Dialing for FXS Ports In the ‘Tel to IP Routing’ page (refer to ''Tel to IP Routing Table'' on page 156), enter 20 for the destination phone prefix, and 10.1.10.2 for the IP address of the FXO device.
Page 348: 7.12.4.6 Fxo Gateway Configuration
MediaPack Series 7.12.4.6 FXO Gateway Configuration The procedure below describes how to configure the FXO device (to which the PBX is directly connected). To configure the FXO device, take these 4 steps: In the ‘Endpoint Phone Numbers’ page, assign the phone numbers 200 to 207 to the device’s FXO endpoints.
Page 349: 7.12.5 Sip Trunking Between Enterprise And Itsps
Proxy Sets, IP Groups, and Accounts, you can "design" complex routing schemes. This section provides an example of an elaborate routing scheme for SIP trunking between an Enterprise and two Internet Telephony Service Providers (ITSP), using AudioCodes' device. Scenario: In this example, an Enterprise has depployed the 8-FXS port MediaPack. The first four phones connected to MediaPack's FXS ports are to operate with ITSP 1 (using UDP), while the next four phones (channels 5-8) are to operate with ITSP 2 (using TCP).
Page 350: Figure 7-19: Configuring Proxy Set Id #1 In The Proxy Sets Table
MediaPack Series To configure call routing between Enterprise and two ITSPs using the device, take these 8 steps: Enable the device to register to a Proxy / Registrar server, using the parameter IsRegisterNeeded in the 'Proxy & Registration' page (refer to ''Proxy & Registration Parameters'' on page 110).
Page 351: Figure 7-21: Configuring Hunt Groups
SIP User's Manual 7. IP Telephony Capabilities In the ‘Endpoint Phone Number Table’ page (refer to "Configuring the Endpoint Phone Numbers" on page 179), configure Hunt Group ID #1 for channels 1-4, and Hunt Group ID #2 for channels 5-8. Figure 7-21: Configuring Hunt Groups In the 'Hunt Group Settings' page (refer to ''Configuring the Hunt Group Settings'' on page 180), configure 'Per Account' registration for Hunt Group ID #1 and associate it...
Page 352: Working With Supplementary Services
MediaPack Series In the 'IP to Hunt Group Routing' page (refer to ''IP to Hunt Group Routing'' on page 159), configure that INVITEs with "ITSP1" as the hostname in the From URI are routed to Hunt Group #1, and INVITEs with "ITSP2" as the hostname in the From URI are routed to Hunt Group #2.
Page 353: 7.13.1 Call Hold And Retrieve
SIP User's Manual 7. IP Telephony Capabilities 7.13.1 Call Hold and Retrieve Initiating Hold / Retrieve: Active calls can be put on-hold by pressing the phone's hook-flash button. The party that initiates the hold is called the holding party; the other party is called the held party.
Page 354: 7.13.4 Call Forward
MediaPack Series • A presses the hook-flash and puts B on-hold (party B hears a hold tone). • A dials C. • After A completes dialing C, A can perform the transfer by on-hooking the A phone. • After the transfer is complete, B and C parties are engaged in a call. The transfer can be initiated at any of the following stages of the call between A and •...
Page 355: 7.13.5 Call Waiting
SIP User's Manual 7. IP Telephony Capabilities The served party (FXS interface) can be configured through the Web interface (refer to ''Call Forward'' on page 175) or ini file to activate one of the call forward modes. These modes are configurable per device's endpoints. Notes: •...
Page 356: 7.13.6 Message Waiting Indication
MediaPack Series 7.13.6 Message Waiting Indication Support for Message Waiting Indication (MWI) according to IETF <draft-ietf-sipping-mwi- 04.txt>, including SUBSCRIBE (to MWI server). The FXS device can accept an MWI NOTIFY message that indicates waiting messages or that the MWI is cleared. Users are informed of these messages by a stutter dial tone.
Page 357: 7.13.7 Caller Id
SIP User's Manual 7. IP Telephony Capabilities 7.13.7 Caller ID This section discusses the device's Caller ID support. 7.13.7.1 Caller ID Detection / Generation on the Tel Side By default, generation and detection of Caller ID to the Tel side is disabled. To enable Caller ID, set the parameter EnableCallerID to 1.
Page 358: 7.13.7.2 Debugging A Caller Id Detection On Fxo
The above settings allow the FXO to send RTP without immediately seizing the line after receiving the first ring at your PC. Capture the RTP using Wireshark (you can also use DSP trace) and send the file to AudioCodes. SIP User's Manual Document #: LTRT-65410...
Page 359: 7.13.7.3 Caller Id On The Ip Side
SIP User's Manual 7. IP Telephony Capabilities 7.13.7.3 Caller ID on the IP Side Caller ID is provided by the From header containing the caller's name and "number", for example: From: “David” <SIP:101@10.33.2.2>;tag=35dfsgasd45dg If Caller ID is restricted (received from Tel or configured in the device), the From header is set to: From: “anonymous”...
Page 360 MediaPack Series Reader's Notes SIP User's Manual Document #: LTRT-65410...
Page 361: Networking Capabilities
SIP User's Manual 8. Networking Capabilities Networking Capabilities Ethernet Interface Configuration The device's Ethernet connection can be configured (using the ini file parameter EthernetPhyConfiguration) for one of the following modes: Manual mode: • 10Base-T Full-Duplex • 100Base-TX Half-Duplex or 100Base-TX Full-Duplex Auto-Negotiation: chooses common transmission parameters such as speed and duplex mode Auto-Negotiation falls back to Half-Duplex mode when the opposite port is not in Auto-...
Page 362: Stun
MediaPack Series The following figure illustrates the device's supported NAT architecture. Figure 8-1: Nat Functioning The design of SIP creates a problem for VoIP traffic to pass through NAT. SIP uses IP addresses and port numbers in its message body and the NAT server can’t modify SIP messages and therefore, can’t change local to global addresses.
Page 363: First Incoming Packet Mechanism
SIP User's Manual 8. Networking Capabilities To enable STUN, perform the following: Enable the STUN feature using either the Web interface (refer to ''Configuring the Application Settings'' on page 59) or the ini file (set EnableSTUN to 1). Define the STUN server address using one of the following methods: •...
Page 364: No-Op Packets
No-Op packets are sent. This is performed using the RTPNoOpPayloadType ini parameter (refer to ''Networking Parameters'' on page 232). AudioCodes’ default payload type is 120. T.38 No-Op: T.38 No-Op packets are sent only while a T.38 session is activated. Sent packets are a duplication of the previously sent frame (including duplication of the sequence number).
Page 365: Multiple Routers Support
SIP User's Manual 8. Networking Capabilities Multiple Routers Support Multiple routers support is designed to assist the device when it operates in a multiple routers network. The device learns the network topology by responding to Internet Control Message Protocol (ICMP) redirections and caches them as routing rules (with expiration time).
Page 366: Ip Qos Via Differentiated Services (Diffserv)
MediaPack Series IP QoS via Differentiated Services (DiffServ) DiffServ is an architecture providing different types or levels of service for IP traffic. DiffServ (according to RFC 2474) offers the capability to prioritize certain traffic types depending on their priority, thereby, accomplishing a higher-level QoS at the expense of other traffic types.
Page 367: Ieee 802.1P/Q (Vlans And Priority)
SIP User's Manual 8. Networking Capabilities 8.8.2 IEEE 802.1p/Q (VLANs and Priority) The Virtual Local Area Network (VLAN) mechanism enables the device to be integrated into a VLAN-aware environment that includes switches, routers and endpoints. When in VLAN-enabled mode, each packet is tagged with values that specify its priority (class-of- service / IEEE 802.1p) and the identifier (traffic type) of the VLAN to which it belongs (Media, Control, or OAMP / IEEE 802.1Q).
Page 368: Table 8-1: Traffic / Network Types And Priority
MediaPack Series Figure 8-2: Multiple Network Interfaces and VLANs Notes: • For security, the VLAN mechanism is activated only when the device is loaded from the flash memory. Therefore, when using BootP: Load an ini file with VlanMode set to 1 and SaveConfiguration set to 1. Then (after the device is active) reset the device with TFTP disabled or by using any method except for BootP.
Page 369 SIP User's Manual 8. Networking Capabilities Application Traffic / Network Types Class-of-Service (Priority) RTCP traffic Media Premium media T.38 traffic Media Premium media Control Premium control SIP over TLS (SIPS) Control Premium control Syslog Management Bronze Determined by the initiator of the ICMP Management request...
Page 370: Getting Started With Vlans And Multiple Ips
MediaPack Series 8.8.3 Getting Started with VLANS and Multiple IPs By default, the device operates without VLANs and multiple IPs, using a single IP address, subnet mask and default Gateway IP address. This section provides an example of the configuration required to integrate the device into a multiple IPs network withVLANs, using the Web interface (refer to ''Integrating Using the Web Interface'' on page 370) and ini file (refer to ''Integrating Using the ini File'' on page 373).
Page 371: Figure 8-3: Vlan Configuration In The Ip Settings
SIP User's Manual 8. Networking Capabilities Modify the VLAN parameters to correspond to the values shown in the following figure: Figure 8-3: VLAN Configuration in the IP Settings Page Click the Submit button to save your changes. Configure the multiple IP parameters by completing the following steps: In the ‘IP Settings’...
Page 372: Figure 8-5: Multiple Interface Table
MediaPack Series Instead of configuring in the ‘IP Settings’ page, you can use the 'Multiple Interface Table' page, which is accessed from the ‘IP Settings’ page by clicking the right-arrow button alongside the label 'Multiple Interface Table' (refer to ''Configuring the Multiple Interface Table'' on page 56).
Page 373: Integrating Using The Ini File
SIP User's Manual 8. Networking Capabilities 8.8.3.2 Integrating Using the ini File The procedure below describes how to integrate the device into a multiple IPs network with VLANs, using the ini file. The procedure below is based on the example setup described in ''Getting Started with VLANS and Multiple IPs'' on page 370.
Page 374 MediaPack Series Use the BootP/TFTP utility (refer to the Product Reference Manual) to load and burn the firmware version and the ini file you prepared in the previous step to the device (multiple IPs and VLANs support is available only when the firmware is burned to flash).
Page 375: Supplied Sip Software Package
SIP User's Manual 9. Supplied SIP Software Package Supplied SIP Software Package The table below lists the standard SIP software package supplied with the SIP device. Table 9-1: Supplied Software Package File Name Description Ram.cmp file MP124_SIP_xxx.cmp Image file containing the software for the MP-124/FXS device. MP118_SIP_xxx.cmp Common Image file Image file containing the software for MP-11x/FXS devices.
Page 376 MediaPack Series Reader's Notes SIP User's Manual Document #: LTRT-65410...
Page 377: Selected Technical Specifications
Programmable Line Characteristics: Battery feed, line current, hook thresholds, AC impedance matching, hybrid balance, Tx & Rx frequency response, Tx & Rx Gains Note: For a specific coefficient file, please contact AudioCodes. Configurable ringing signal: up to four cadences and frequency from 15 to 200 Hz...
Page 378 MediaPack Series Function Specification modulation, ETSI Type 1, NTT, Denmark, India, Brazil, and DTMF ETSI CID (ETS 300-659-1) Additional Features Polarity Reversal / Immediate or smooth to prevent erroneous ringing Wink Metering Tones 12/16 KHz sinusoidal bursts (applicable only to FXS interfaces) By frequency (15-100 Hz) and cadence patterns Distinctive Ringing Message Waiting...
Page 379 Control Processor Motorola PowerQUICC 870 Control Processor SDRAM - 32 MB Memory Signal Processors AudioCodes AC482 VoIP DSP Interfaces FXS Telephony 2, 4, or 8 Analog FXS phone or fax ports, loop start (RJ-11) Interface FXO Telephony 4 or 8 Analog FXO PSTN/PBX loop start ports Interface MP-118: 4 FXS &...
Page 380: Mp-124 Specifications
Programmable Line Characteristics: Battery feed, line current, hook thresholds, AC impedance matching, hybrid balance, Tx & Rx frequency response, Tx & Rx Gains Note: For a specific coefficient file, please contact AudioCodes. Configurable ringing signal: up to 4 cadences and frequency from 15 to 200 Hz...
Page 381 IP stack (UDP, TCP, RTP) Remote software upload (TFTP, HTTP and HTTPS) Loop-start signaling Line Signaling Protocols Processor Control Processor Motorola PowerQUICC 860 SDRAM – 64 MB Control Processor Memory Signal Processors AudioCodes AC482 VoIP DSP Version 5.4 May 2008...
Page 382 MediaPack Series Function Specification Interfaces 24 Analog FXS phone or fax ports, loop start (RJ-11) FXS Telephony Interface Network Interface 10/100Base-TX RS-232 Interface RS-232 Terminal Interface (DB-9) Channel status and activity LEDs Indicators Connectors & Switches Rear Panel: 50-pin Telco shielded connector 24 Analog Lines Ethernet 10/100Base-TX, RJ-45 shielded connector...
Page 383: Glossary
Standard companding algorithm, used in European digital communications systems to optimize the dynamic range of an analog signal for digitizing. Address of Record Bits per second BootP AudioCodes Proprietary Bootstrap Loader Utility Class of Service Compressed File (device Firmware) Call Progress Tones Decibels...
Page 384 Media Server Control Markup Language Message Waiting Indicator NAPTR Naming Authority Pointer Network Address Translation NetCoder AudioCodes Proprietary High Quality, Speech Coder Network File System Numbering Plan Indicator Network Time Protocol OAMP Operations, Administration, Maintenance and Provisioning Open Systems Interconnection (Industry Standard)
Page 385 SIP User's Manual 11. Glossary Term Meaning Service Record Secure Shell Secure Socket Layer (also known as Transport Layer Security (TLS)) STUN Simple Traversal of UDP through NATs Transmission Control Protocol TCP/IP Transmission Control Protocol / Internet Protocol Time-Division Multiplexing TFTP Trivial File Transfer Protocol Transport Layer Security...
Page 386 User's Manual Version 5.4 www.audiocodes.com...

This manual is also suitable for:

Mediapack mp-11 series

AudioCodes MediaPack MP-124 User Manual

1 Overview

2 Configuration Concepts

3 Web-Based Management

4 Ini File Configuration

5 Default Settings

Quick Links

Related Manuals for AudioCodes MediaPack MP-124

Summary of Contents for AudioCodes MediaPack MP-124