User Manual - Invacare Aquatec Sorrento User Manual

Aquatec® Sorrento
• Backrest
• Backrest holder (2x)
•

User manual

8 Product Description
Aquatec Sorrento bath tub swivel seat is a bathtub seat. The
seat can be rotated and it is supported by four feet to be
placed on the bathtub's edges.
9 Intended Use
This product is intended to be used as a shower aid.
Users are any adults and adolescents with restricted or
limited mobility (e.g.: legs and/or hips). If used without an
assistant, the users must be able to keep their own balance.
Indication
Restricted or limited mobility (e.g.: legs and/or hips) or
having balance issues to stand up or walk due to transitional
or permanent disabilities
There are no contraindications known when using the
product as intended.
The maximum user weight is 130 kg.
10 Assembly and Setup (Fig. 4 - 9)
CAUTION!
Risk of Entrapment
– Take care during assembly.
Fitting the Armrests (Fig. 4)
1. Drop armrests A into seat plate B on both sides, see
Fig 4.
WARNING!
Risk of Injury
– Ensure that both catches C in each armrest
audibly engage on the underside of the seat
plate, see Fig 4.
CAUTION!
Risk of Entrapment
– Do not put your fingers in open holes at the
armrest and below the seat.
Fitting the Backrest (Fig. 5 - 6)
1. Push backrest frame A into the rear openings of seat
plate B on both sides, see Fig 5.
WARNING!
Risk of Injury
– Ensure that both catches C of the backrest
frame audibly engage on the underside of the
seat plate, see Fig 5.
2. Pull down backrest cover A over both sides of the
backrest frame, see Fig 6.
WARNING!
Risk of Injury
– Ensure that the ends of the backrest frame are
properly located in the recesses D on the right
and left of the backrest cover, see Fig 6.
3. Close the backrest bands by pushing latches C into
buckles B, see Fig 6.
4
WARNING!
Risk of Injury
– Make sure that all buckles are securely closed.
4. Tighten the backrest bands, see Fig. 9.
Tighten or slacken the bands to adjust the firmness
of the backrest cover.
Placing the Swivel Seat on the Bathtub (Fig. 7 - 8)
1. Remove the safety clips A on both sides, see Fig 7.
2. Slide the feet B inwards.
3. Place the swivel seat with the feet facing towards the
bottom of the bathtub.
4. Slide all feet B equally to the inner edge of the bathtub
until their maximum extend.
WARNING!
– Make sure that the swivel seat feet are
positioned to securely fit against the inner wall
of the bathtub. (Fig. 7)
5. Secure all four feet by installing the safety clips C on
both sides.
6. The swivelling mechanism is released by pulling up the
lever. The seat can now be swivelled by 360°. (Fig. 8)
The chair is disassembled in reverse order to assembly.
11 Maintenance
11.1 General Maintenance Information
This product is maintenance-free, provided that the cleaning
and disinfection instructions are adhered to.
11.2 Cleaning and Disinfection
General Safety Information
CAUTION!
Risk of Contamination
– Take precautions for yourself and use
appropriate protective equipment.
IMPORTANT!
Wrong fluids or methods can harm or damage
the product.
– All cleaning agents and disinfectants used must
be effective, compatible with one another and
must protect the materials they are used to
clean.
– Never use corrosive fluids (alkalines, acid etc.)
or abrasive cleaning agents. We recommend
an ordinary household cleaning agent such as
dishwashing liquid, if not specified otherwise in
the cleaning instructions.
– Never use a solvent (cellulose thinner, acetone
etc.) that changes the structure of the plastic
or dissolves the attached labels.
– Always make sure that the product is completely
dried before taking it into use again.
For cleaning and disinfection in clinical or long-term
care environments, follow your in-house procedures.
1528667-C