User Manual Model NVXM1000 Navigation With XM™ Ready Copyright Audiovox Electronics Corp. 150 Marcus Blvd., Hauppauge, NY 11788 Call center: 800 290 6650 128-7995...
You always have complete freedom to go wherever you wish. Just insert the memory card and go. You do not need a stylus to use the NVXM1000. All screen buttons and controls are designed so that you can operate them with your fingertips.
Introduction Thank you for choosing the Navigation with XM® Ready unit, Model NVXM1000, as your door-to-door in- car navigator complete with integral XM® Radio capability. In addition, the NVXM1000 exhibits other features, such as Back-Up Camera input using an appropriate cradle and interconnect cable, and Music input from an external source such as an SD card.
NVXM1000 Location of Controls, Indicators and Connectors The NVXM1000 provides a number of controls, indicators and connectors to facilitate user operation and interconnection with external power, navigation, music and XM® inputs and outputs. Volume Up/Down Control XM Mini-Tuner Slot SD Card...
Navigation with XM® Ready is designed for easy operation. Consistent with these criteria, a minimum of hardware buttons is used on the NVXM1000; these consist of the Home button, Power On/Off slide switch and the Volume control. The remaining controls are operated by touching the LCD screen to access submenus pertaining to the various operating modes and their submenus and lists.
Figure 2. Jensen Logo at Power On e. If the NVXM1000 was recently on and being used, and has been turned off (standby mode) using the Home button ( unit and the operational modes default display appears. Figure 3. Operational Modes Default Display...
MUSIC: Play music stored on the internal hard drive or the external multi-media slot (SD) on the left side of the unit. d. Back Up Cam: Using an optional NVXM1000 cradle and back-up camera installed in the vehicle, and a cable for camera-to-cradle interconnection.
NVXM1000. XM Ready Mode 1. Hardware and Subscription To listen to XM satellite radio on the NVXM1000, the following optional items are required: • XM Mini-Tuner • XM antenna installed in your vehicle.
Figure 5. Check XM Mini-Tuner Warning Display Message b. Plug the external XM antenna cable into the XM ANT jack at the rear of the unit and set the Power On/Off slide switch to the On position. If the antenna is faulty or improperly connected, the following message appears on the display: Figure 6.
Tuner unit is activated, you will be able to access over 170 digital radio channels. XM Ready Default Display Screen While tuned to an XM channel, the NVXM1000 XM default display contains information about that channel as shown below. http://activate.xmradio.com (1-800-967-2346).
Page 13
Figure 8. Typical XM Channel Default Display Screen Initial activation may require up to 15 minutes to download the XM Note: channel list to the NVXM1000. Table 2. XM Default Display Function Buttons Return to Operational Modes Default Display .
This feature allows you to capture and store the current program data information (Channel Name & Number/ Artist & Song Title). You can store up to 30 Artist/Song Title combinations. The NVXM1000 also has the capability to search the current incoming XM signal, and thereby alert you if it matches the Artist/Song title stored in NVXM1000 memory, or becomes available on any other channel.
Figure 9. Saving a Favorite Artist / Song in Memory Figure 10. Recalling a Saved Artist / Song Title from Memory Preset 1. Preset Banks A, B and C, and Direct Button To preset favorite channels into memory, you can use the preset functions consisting of the preset bank (Preset A, Preset B, Preset C) and the ”...
Page 16
Figure 12. Preset Display For Storing a Desired Channel Recalling a Channel From a Preset Bank To recall a channel from a preset bank: 1. Toggle the bank. 2. Press the PRESET button just below the preset bank button; the preset channel appears on the display as shown above.
Table 3. Preset Mode Function Button Summary Exit preset mode Keypad buttons Store preset channel numbers Recalling preset channel numbers into memory Jump Button The JUMP button, when pressed, allows you to immediately return to the previous channel, or alternately jump between the previous and current channel. Category Button The CATEGORY ...
Figure 13. XM Setup Display A description of the setup choices is presented in Table 4. Table 4. XM Setup Button Functions Antenna Aiming Display. Upon entering this mode, two vertical bar graphs are displayed representing terrestrial (tower) and satellite transmitters. The signal strength is displayed by the respective graph segments.
Page 19
Upon entering this mode, you may clear all 30 memory locations (erase all), or just specific memory locations (erase some) can be cleared. The following adjustment options are possible: Figure 15. Tune Select Display a. Clear all Memory Locations. Press the Erase All button; a prompt display screen appears confirming Please Confirm Your Selection? Press the Yes or No button as desired.
Figure 18. Selecting Clear by Artist, Song Title or Both Channel Add/Skip Display When the Channel Add/Skip button is pressed on the setup display, a channel list is displayed with the current channel highlighted. Use the channel up/down buttons to navigate through the list.
Page 21
Table 5. Summary of Data Service Sub-Modes Stock Service Operation When the Stock button is pressed, Stock On/Off, Add Stock, Erase All and Erase Some options are displayed for information and control: Figure 21. Data Service Stock Options Display A summary of available stock operational modes is presented in Table 6. Table 6.
Page 22
Figure 22. Scrolling Stock Information Display 2) Add Stock – Pressing this button enables the Data Service Add Stock display as shown in Figure 22; Table 7 explains the control buttons on this display. Figure 23. Add Stock Display Table 7. Summary of Add Stock Control Buttons Exit Stock Add mode Spelling scroll down Previous character entry...
Page 23
Figure 24. Stored, Already Stored and Stock Full Pop-Up Windows 4) Erase All/Erase Some Stock Entries – When the Erase All button is pressed on the Data Service menu, a pop-up window appears on the display asking Please Confirm Your Selection. In the case of erase all, when Yes is pressed, all stock entries are erased and the display reverts to the Add Stock display.
Page 24
When the Info Extra button is pressed, Info Extra On/Off, and Select options are displayed for information and control: Figure 27. Data Service Info Extra Display A summary of available Info Extra operational modes is presented in Table 7. Table 7. Summary of Info Extra Control Buttons 1) Info Extra On/Off –...
XM Ready and Navigation Dual Operation It is possible to simultaneously listen to XM radio while operating in the navigation mode on the NVXM1000. To accomplish dual operation, proceed as follows: a. Initiate the Navigation mode of operation following the previous instructions in this manual.
d. The dual modes display appears as shown in Figure 30. In this operational environment, both modes --- Navigation and XM Ready --- are fully operational. The same is true for the Music and Navigation dual operating modes. Figure 30. Navigation and XM Ready Dual Operating Modes Display Table 8.
Page 27
Figure 31. Music Mode Default Display Table 9 summarizes the control button functions on the Music mode display. Table 9. Music Mode Control Button Functions Play Present Song Being Loaded Play Previous Song Play Next Song Pause Current Song Stop Current Song Display Main Setup Menu (FM Transmitter, etc.) Display Folder Lst Randomly Play All Songs Within HDD or SD...
Display Next List Within Current Folder a. Playing Music You can play music stored on the NVXM1000 hard disk (HDD), or from an SD card. 1. If music is stored on a personal computer, insert the USB connector directly into the USB port on the right side of the unit, and the other end into an available USB port on your PC.
Music and Navigation Dual Display It is possible to simultaneously listen to music while operating in the navigation mode on the NVXM1000. To accomplish dual operation, proceed as follows: 1. Initiate the Navigation or Music mode following the previous instructions in this manual.
D. Back Up CAM Mode (Optional Cradle Required) Available Late 2007 The NVXM1000 can be used in the back-up camera mode provided all the necessary equipment and interconnections have been satisified. Getting Started To view the Back up camera screen two things are required in addition to your NVXM1000: •...
Table 12 describes the control button functions on this display. Table 12. Media Display Control Button Functions Quit Media and Return to Main Menu Operate Video Demo Mode Operate Photo Mode 1. Store Demo – Enter STORE DEMO to obtain a slideshow of how to operate the NVXM1000.
SD card containing digital camera images, or by using an external USB input from a computer hard drive, and copy the files to the NVXM1000. (Similar operation to music download explained in the Music Mode previously.) Figure 36 illustrates a typical pnoto display, while Table 13 summarizes the button functions.
Figure 37. Full Screen and Slide Mode Display SETUP MODE Prior to operating the NVXM1000 and implementing the various modes available to you, you may wish to configure the unit to your personal preferences. To accomplish this goal, you must enter the SETUP mode, which is offered on the Main Menu.
Page 34
Quit and Exit Setup Mode Battery Charge Status Indicator Speaker Volume Status Indicator Execute Set Calibration Program Set Brightness Level Set Display Duration of Main Menu Screen Increase Brightness Level (1- 2 - 3 - 4 - 5) Increase Display Duration (2, 4, 6, 8 sec, ON) Decrease Brightness Level (5 - 4 - 3 - 2 - 1) Decrease Display Duration (ON, 8, 6, 4, 2sec) FM Frequency and Audio Setting Mode...
Page 35
b. Repeat as the target moves around the screen; the pressure for your particular touch is now calibrated. Brightness Sub-Mode – To adjust the brightness of the LCD display, press the + or – buttons to increase or decrease LCD screen brightness per your personal taste.
Page 36
Store Current Channel / Recall the Stored Fmt Channel Store Current Channel / Recall the Stored Fmt Channel Store Current Channel / Recall the Stored Fmt Channel Speaker This feature allows the user to control internal speaker ON or OFF Green back ground : Internal Speaker ON / FMT OFF Grey back ground : Internal Speaker OFF / FMT ON FMT (FM Transmitter)
Page 37
Setup System Mode – When the System button is pressed on the Setup screen the display presents the Model Name of the unit (NVXM1000) plus the OS Version, Software (SW) Version, and the Navigation (NAV) Version of the current unit.
Remote Control Configuration Table 17 summarizes the button functions on the remote control. Table 17. Remote Control Button Functions H. Media, Back-Up Camera, Photo, Music and Setup...
1. Make sure both the PC and the NVXM1000 are turned on. 2. Connect one end of a USB cable to the USB port on the NVXM1000. 3. Connect the other end of the USB cable to the PC’s USB port.
2. Windows opens a screen showing all the drives on your computer and assigns a drive letter to the NVXM1000 based on the other drives in your system. Therefore, the drive letter you see may be different from the one in the example of Figure 44 below.
LCD Pixels: K. Troubleshooting Table 19 presents a troubleshooting chart representing the most common trouble symptoms affecting the NVXM1000. Table 19. NVXM1000 Troubleshooting Chart Description The power cable may not be NVXM1000 does not turn on. Main hardware switch on bottom of...