Related Manuals for Audiovox AMP-590A
Summary of Contents for Audiovox AMP-590A
- Page 1 ModelAMP-590A 150WattStereoAmplifier Owner's Owner's Owner's Owner's Owner's Manual Manual Manual Manual Manual...
-
Page 2: Table Of Contents
INDEX Specifications ...1 Precautions ...2 Installation Instructions ...3 Wiring Instructions ...4 - 5 Input Wiring Diagram ...6 Output Wiring Diagram ...7 Operation ...8 Warranty ...9 128-5412 SHT. 2 OF 12... -
Page 3: Specifications
50 dB Signal / Noise Ratio: 80 dB (A-Weighted) Input Impedance: low-level 10K ohms high-level 100 ohms * Due to continuing improvement, Audiovox reserves the right to change features and design without notice. HELP! 1-800-645-4994 Monday-Friday Saturday Input Sensitivity: low-level 200 mv. - 2 v. -
Page 4: Precautions
6. Make certain that the speakers to be used with this amplifier are capable of handling the output power (wattage) of the unit. Use of speakers not rated for the output of this amplifier may cause damage to or failure of the speakers for which Audiovox will not be liable. -
Page 5: Installation Instructions
INSTALLATION INSTRUCTIONS 1. Select a mounting area where the amplifier will have sufficient air circulation for proper cooling. Inadequate air circulation will cause the temperature of the amplifier to rise and will trigger the thermal protection mode. 2. Place the amplifier on the mounting surface and mark the locations of the four mounting holes as shown in the illustration. -
Page 6: Wiring Instructions
WIRING INSTRUCTIONS The power and speaker wire connections for this amplifier are made via screw tightened terminal blocks. Loosen the screw for the connection to be made and fully insert the wire (strip 1/2" of insulation from the end) into the respective screw on the side panel (crimp-on "U"... - Page 7 WIRING INSTRUCTIONS 4. Speaker Connections Depending on the type and number of speakers used with the amplifier, wire them to the speaker terminals as per the appropriate wiring diagram. For most applications, #18 gauge wire should be used for the speaker leads but in no case thinner than #20 gauge.
-
Page 8: Input Wiring Diagram
INPUT WIRING DIAGRAM LOW-LEVEL HIGH-LEVEL CAR STEREO (SPEAKER) OUTPUTS RCA OUTPUTS RIGHT LEFT RIGHT LEFT LEFT RIGHT CHASSISGROUNDONRADIO IMPORTANT USE EITHER HIGH-LEVEL OR LOW-LEVEL INPUTS, NOT BOTH. 5-PIN RCA TYPE CONNECTOR SHIELDED CABLE (NOT INCLUDED) LOW INPUT HIGH LEVEL GAIN MIN MAX... -
Page 9: Output Wiring Diagram
WARNING! THIS AMPLIFIER IS DESIGNED FOR USE WITH 2 SPEAKERS NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 1 SPEAKER. NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. FAILURE TO WIRE CORRECTLY MAY CAUSE DAMAGE TO THE AMPLIFIER. EXISTING SCREW OR BOLT CLEAN PAINT, RUST, DIRT OR GREASE FROM AREA FOR GOOD CONNECTION... -
Page 10: Operation
OPERATION HIGH LEVEL GAIN LOW INPUT MIN MAX After initial set-up, the amplifier should not require any further adjustment unless there is a change in the car stereo or speaker system with which it is used. Power Indicator LED The Power Indicator LED will light to indicate that the unit is connected to the battery and that the Remote Turn-On terminal is receiving +12 volts, thus turning on the amplifier. -
Page 11: Warranty
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. - Page 12 © 1998 Audiovox Corp., Hauppauge, N.Y. Printed in Korea Form No. 128-5412...