Advertisement
2. Locate the center of the mounting location and mark it. Allow
enough clearance to accommodate the AT8474 mount on
the desired surface and make certain there are no physical
obstructions below the desired location.
3. Locate the three mounting screw holes and mark them.
4. Using a 1" hole saw, drill the through-hole for the microphone body.
(Note: although a 1" drill bit will work, a hole saw provides
for a cleaner hole and is less likely to damage the table surface.)
5. Using a
1
/
" (1.5 mm) drill bit, drill three pilot holes for the mounting
16
screws. (If mounting below the table surface, be certain NOT to drill
pilot holes through the table.)
6. Place the AT8474 mount over the hole and partially tighten the
three screws. Then place the microphone in the AT8474 so that
the microphone's power module (base) extends through the
AT8474 mount into the hole. Tighten all three screws evenly.
For maximum security, the screws should be tight enough to
ensure that the microphone is held securely in place and can
not be removed without loosening the screws.
7. If mounting the AT8474 mount below the surface of the table,
slide the rubber trim ring over the microphone (above the table
surface) and seat it between the microphone and the sides of
the hole for a finished appearance. (If mounting the AT8474
above the surface of the table, you may also choose to use the
trim ring beneath the surface of the table, for added attenuation
of noise, shock and vibration.)
8. After installing the microphone, assure maximum shock mount
effectiveness by providing some slack in the connecting cable.
The cable can be secured to the table with a standard wire clip
or cable tie (not included).
0.33"
8.4 mm
0.48"
12.3 mm
24.00"
609.6 mm
TO
12.00"
304.8 mm
0.74"
18.9 mm
ES915SC SPECIFICATIONS
†
ELEMENT
POLAR PATTERN
FREQUENCY RESPONSE
LOW-FREQUENCY ROLL-OFF
OPEN CIRCUIT SENSITIVITY
IMPEDANCE
MAXIMUM INPUT SOUND LEVEL
DYNAMIC RANGE (typical)
SIGNAL-TO-NOISE RATIO
1
SWITCHES
PHANTOM POWER REQUIREMENTS 11-52V DC, 4 mA typical
WEIGHT
ES915SC12
ES915SC15
ES915SC18
ES915SC21
ES915SC24
DIMENSIONS
ES915SC12
ES915SC15
ES915SC18
ES915SC21
ES915SC24
All
OUTPUT CONNECTOR
OPTIONAL INTERCHANGEABLE
ELEMENTS
ACCESSORIES FURNISHED
†In the interest of standards development, A.T.U.S. offers full details on its test
methods to other industry professionals on request.
*1 Pascal = 10 dynes/cm
2
= 10 microbars = 94 dB SPL
1
Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
Polar Pattern
LEGEND
200 Hz
1 kHz
5 kHz
SCALE IS 5 DECIBELS PER DIVISION
8 kHz
Frequency Response
Frequency in Hertz
LEGEND
12" or more on axis
Roll-off
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
www.audio-technica.com
P51923 ©2007 Audio-Technica U.S., Inc.
Fixed-charge back plate
permanently polarized condenser
Cardioid
30-20,000 Hz
80 Hz, 18 dB/octave
–40 dB (10.0 mV) re 1V at 1 Pa*
250 ohms
138 dB SPL, 1 kHz at 1% T.H.D.
109 dB, 1 kHz at Max SPL
65 dB, 1 kHz at 1 Pa*
Flat, roll-off; mute/on
125 g (4.4 oz)
130 g (4.6 oz)
135 g (4.8 oz)
140 g (4.9 oz)
145 g (5.1 oz)
304.8 mm (12.00") long
381.0 mm (15.00") long
457.2 mm (18.00") long
533.4 mm (21.00") long
609.6 mm (24.00") long
8.4 mm (0.33") head diameter,
18.9 mm (0.74") base diameter
Integral 3-pin XLRM-type
ESE-O omnidirectional (360°);
ESE-H hypercardioid (100°);
ESE-ML MicroLine
®
(90°)
AT8109 two-stage foam
windscreen; AT8474 universal
isolation mount; AT8473 quick-
mount stand adapter;
5
/
"-27 to
8
3
/
"-16 threaded adapter
8
Printed in U.S.A.
Advertisement
