Control Port Function; System Control (Cpu : Ic801) - Sanyo VIZZON HT30746 Service Manual

System Control (CPU : IC801)

Pin Name
1 CVin
2 P70/INT0/TOLCP
3 P71/INT1/TOHCP
4 P72/INT2/TOIN
5 P73/INT3/TOIN
6 AN0
7 AN1
8 P82/AN2
9 P83
10 P84/AN4
11 P85/AN5
12 P86/AN6
13 P87/AN7
14 P30/SO6
15 SB6
16 SCK6
17 SB6
18 SCK6
19 DBGP0
20 DBGP1
21 DBGP2
22 PC0
23 PC1
24 PC2
25 PC3
26 PC4
27 P00
28 P01
29 P02
30 P03
31 P04
32 P05
33 P06
34 P07
35 P20/SO1
36 P21/S11/SB1
37 P22/SCK1
38 P23
39 UTX
40 URX
41 P26/OSDCK1
42 BL2
43 VSS2
44 VDD2
45 P10/SO0
46 P11/SI0/SB0
47 P12/SCK0
48 P13
49 PWMA
50 PWMB
51 PWMC
52 P17/PWMD
53 BL1
54 B
55 G
56 R
57 HSB
58 VSB
59 VSS1
60 XT1
61 XT2
62 VDD1
63 RESB
64 FILT

CONTROL PORT FUNCTION

Function
Cvin
Reserve
Reserve
Reserve
Rcin
Key in
AFT S-Figure in
Reserve
Reserve
Reserve
Reserve
TV Relay out
IIC-BUS for NV
IIC-BUS for NV
IIC-BUS for TV
IIC-BUS for TV
TB in
Fix/Variable
WDT out
AV SW1
AV SW2
AV SW3
BPF SW
Power Fail in
STATUS in
Ack out
Reserve
Reserve
Reserve
Audio MUTE
UART OUT
UART IN
Reserve
Reserve
Vss
Power IN
Reserve
Reserve
Reserve
Normal SW
CUT OFF ADJ-1
CUT OFF ADJ-2
CUT OFF ADJ-3
Reserve
OSD BLK out
OSD B out
OSD G out
OSD R out
Hsync
Vsync
Vss
Xin
Xout
Power IN
RESET in
FILT out
I/O Description
IN Video Signal Input (Not used)
IN RC Input
IN Key Input
IN AFT S-Figure Input
IN S-Detect
OUT POWER Relay SW
I/O (DATA) Active 'L' for IIC data NV
OUT (CLOCK) Active 'L' for IIC clock NV
I/O (DATA) Active 'L' for IIC data TV
OUT (CLOCK) Active 'L' for IIC clock TV
Terminal for De-Bug 1
Terminal for De-Bug 2
Terminal for De-Bug 3
Writing on board (ENA/DATA1)
Writing on board (DATA0)
Writing on board (CLK)
IN Detection for Video Signal (Time base: H)
OUT Audio Control (Reserved)
OUT Watch dog timer (Reserved)
OUT Selection for AV Selector 1
OUT Selection for AV Selector 2
OUT Selection for AV Selector 3
OUT For Bandpass Filter (Reserved)
IN At the time of the TV power error(L)/ordinariness (H)
IN For factory use
OUT For factory use
OUT "MUTE:H, OTHER:L"
OUT Digital Module microcomputer piece confidence
IN Digital Module microcomputer piece confidence
IN GND (0Vdc)
IN 5V (5Vdc±10%)
OUT (Reserved)
OUT Cut-off Adjust 1 (Reserved)
OUT Cut-off Adjust 2 (Reserved)
OUT Cut-off Adjust 3 (Reserved)
OUT polarity : positive
OUT polarity : positive
OUT polarity : positive
OUT polarity : positive
IN polarity : negative
IN polarity : negative
IN GND (0Vdc)
IN Main Clock IN/OUT Fosc=8MHz
OUT ( Should be connected between IN/OUT pins.)
IN 5V (5Vdc—10%)
IN Reset terminal
PLL Filter
— 51 —