Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Siemens Cm-lon 6BK1700-0BA10-0AA00
Summary of Contents for Siemens Cm-lon 6BK1700-0BA10-0AA00
- Page 1 Manual Release 04/2002 cm-lon FOR LOGO! Communication with LOGO! with LON systems...
- Page 2 CM LON LOGO! Expansion Module Manual Chapters Safety Notices Getting to know CM LON Mounting and wiring the CM LON Putting the CM LON into operation Supported functions CM LON specifications INDEX...
- Page 3 CM LON LOGO! Expansion Module Copyright - Siemens AG 1996 - 2002 All rights reserved You may not transfer or duplicate this document or utilize or reveal its contents, unless expressly authorized in writing. In the case of a violation, you will be obliged to pay damages.
-
Page 4: Table Of Contents
LOGO! Expansion Module CM LON Table of Contents Safety Notices Getting to know CM LON ........5 What is CM LON?............. 5 The construction of the CM LON ......6 Mounting and wiring the CM LON......7 General guidelines ............ 7 Wiring the CM LON........... -
Page 5: Safety Notices
CM LON LOGO! Expansion Module Safety Notices Indicates that death, severe bodily injury or substantial material damage will occur, if the corresponding safety measures are not taken. DANGER Indicates that death or severe bodily injury may occur, if the corresponding safety measures are not taken. -
Page 6: Getting To Know Cm Lon
LOGO! Expansion Module CM LON Getting to know CM LON 1.1 What is CM LON? The Local Operating Network (CM LON) communications module is an interface for connecting LOGO! onto a LON Works network. The LOGO! communications module has been implemented as a Slave module for the LOGO control module (12/24 or 110/240 Volt). -
Page 7: The Construction Of The Cm Lon
CM LON LOGO! Expansion Module 1.2 The construction of the CM LON 1. Power supply 2. Bus lock slider, interface to the LOGO! 3. The RUN/STOP LED for LOGO! communication 4. The BUS LED - LON communications 5. Input - LON connection 6. -
Page 8: Mounting And Wiring The Cm Lon
LOGO! Expansion Module CM LON Mounting and wiring the CM LON 2.1 General guidelines The following guidelines should be observed when mounting wiring your CM LON: When wiring the CM LON, make certain that you follow all of the applicable and legally binding standards. Observe all of the relevant national and regional regulations when installing and operating the device. - Page 9 CM LON LOGO! Expansion Module Please notice: The CM LON must have its own power supply (12/24 V AC/DC). NOTE This module may only be mounted and wired by qualified personnel, who know and observe the generally applicable guidelines and applicable regulations and standards. Observe the assembly and disassembly instructions in the LOGO! manual.
-
Page 10: Wiring The Cm Lon
LOGO! Expansion Module CM LON 2.2 Wiring the CM LON To wire the CM LON, use a screwdriver with 3 mm wide blade. - You do not need to use wire end ferrules when clamping the wires. NOTE After the installation, the terminals must be covered. To protect personnel against unintentional contact with the portions of the CM LON that are conducting electricity, the appropriate national and local standards must be observed. -
Page 11: Connecting The Power Supply
CM LON LOGO! Expansion Module 2.2.1 Connecting the power supply The CM LON has been designed to serve as a Slave module for the LOGO! controller. It must be connected to a 24 V AC/DC supply voltage. Please observe the relevant instructions that are found in the product information that was included with your equipment as well as the technical data regarding the permissible voltage tolerances, main frequency and current consumption. -
Page 12: Connecting The Lon
LOGO! Expansion Module CM LON 2.2.2 Connecting the LON This connection is made using the two screw terminals A-B. RUN/STOP 6BK1 700-0BA10-0AA0 Service You can start the programming by pressing the “Service ↓” button. NOTE Don't apply force when pressing the “Service ↓” button. When contact has been made, the LED will light up in orange. -
Page 13: Putting The Cm Lon Into Operation
CM LON LOGO! Expansion Module Putting the CM LON into operation A LONMARK certified application was loaded into the CM LON at the factory. Other applications can – where available – also be loaded. 3.1 Step-by-step 1. Interrupt the voltage to the LOGO!. (The LOGO! and its modules do not have power switches.) 2. -
Page 14: The Cm Lon - Operational Status
LOGO! Expansion Module CM LON 8. To log a CM LON in on a LON Works network, you can either press the “Service” button or enter the Neuron-ID directly in the LON using the Installation Tool or by reading the label with a bar code scanner. 9. - Page 15 CM LON LOGO! Expansion Module LED Lights In Green (RUN) Red (STOP) Orange The expansion module The expansion module The expansion is communicating with module's initialization is not communicating the device on the left. phase with the device on the left.
-
Page 16: Behavior In Case Of A Fault
LOGO! Expansion Module CM LON 3.3 Behavior in case of a fault LOGO! - Power failure If the power to the LOGO! fails or the communications with the LOGO! Master or the communications partner to the left is interrupted, the outputs will be set to 0. The “RUN/STOP” LED will light in RED after one second. -
Page 17: Supported Functions
CM LON LOGO! Expansion Module Supported functions The CM LON handles the communications between: The LOGO! and LON Supports virtual inputs and outputs for the communication via the LON. 4.1 Virtual inputs / outputs The standard CM LON application fills the complete LOGO! process image. - Page 18 LOGO! Expansion Module CM LON LOGO! DM 8 CM LON I1 I2 I3 I4 I5 I6 I7 I8 I9I10I11I12 & Q5 Q6 Q7 Q8 I13 ... I24 Q9 ... Q16 1. To map the LOGO! inputs (I1 to I8/I12) as outputs on the BUS, these must be joined with free virtual BUS outputs (Q5/Q9 to Q12) in the LOGO! application.
-
Page 19: Available Network Variables
CM LON LOGO! Expansion Module 4.2 Available network variables The CM LON's standard LON application contains the network variables described below. LonMark Node Object Quantity Name Type Description nviRequest SNVT_obj_request Request object mode nvoStatus SNVT_obj_status Output object status nvoFileDirectory SNVT_address File directory for direct read/write LonMark Controller Object... -
Page 20: Lon Configuration Parameters
LOGO! Expansion Module CM LON 4.3 LON configuration parameters All of the digital outputs are configured with a “Send Heartbeat”. The LON application is configured using the Config Network Variables. The following CPTs are available. Index Description Name Default SCPTmaxSendTime Send Heartbeat maxSendTimeDO05 0 min... -
Page 21: Inputs / Outputs - Special Considerations
CM LON LOGO! Expansion Module 4.4 Inputs / Outputs – special considerations Allocating the LOGO! inputs/outputs All of the inputs/outputs, which are physically allocated on the LOGO! or an expansion module, are not available for allocation as virtual inputs/outputs. Only the outputs on additional I/O modules can be issued in parallel to the LON. -
Page 22: Cm Lon - Specifications
LOGO! Expansion Module CM LON CM LON - Specifications Electrical Data Supply voltage 24 V AC 24 V DC Permissible range -15% +10% -15% +20% Current consumption max. 33 mA Data transmission rate - LON 78 kBaud Physical Construction Standard width 2 SU Dimensions (W x H x D) 36 x 90 x 55 mm... - Page 23 CM LON LOGO! Expansion Module Safety Protection standard IP 20 Radio interference suppression EN 55011 (Limit Value Class B) Certification LON MARK UL 508 VDE 0631 IEC 61131-2 Overvoltage protection Fuse 80 mA slow action fuse Order Data LOGO! Expansion Module CM LON 6BK1700-0BA10-0AA00 CM LON J31069-D1263-U002-A2-7618...
- Page 24 LOGO! Expansion Module CM LON INDEX Local Operating Network SNVT Standard Network Variable Type CM LON J31069-D1263-U002-A2-7618...
- Page 25 Siemens Aktiengesellschaft Automation and Drives Systems Engineering PO. 2355, D-90713 Fürth w w w . s i e m e n s . c o m Order No. J31069-D1262-U002-A2-7618...