Table of Contents
Advertisement
T
T
OUCH
RACKER
RVEIMKITE T
T
OUCH
RACKER
Part Number
Description
6003-0047-01
CBL/A, MDR, 14',8 C,CROSS-P'D
5899-0004-102
SCR, TCUT, M2.9X9.5, PHP, ST,Z,T1
2880-0083-01
ANCH, PL, W/O SCR, 3/4L,#4-#6-#8
2816-7634-44
SCR, TYP AB, PHP, ST, Z, 8X1
2109-0254-04
CON, P, EUR,.2C,28-12G,1X5P
2141-0002
LUG, SPADE, INSUL, 22-168
6002-0024-01
CBL, 3C, 18G, CM
0649-0006-02
BAG PLASTIC 4 X 6 1/2 4MIL
0649-0006-04
BAG PLASTIC 8 X 10 4 MIL THK
2450-0008-01
LBL, BLNK, PAP, THERM, 89X76M, RL
3600-0032-01
PRINTING SPEC, LABEL
0300-1000-01
INTERCONNECT BOX, TOUCH TRACK
6003-0107-01
CBL/A, QUAD, SW, INTFCE
2125-0007-02
HOOD, D, 9P, EMI/RFI, 1/4 D CBL
2130-0021-01
CON, D,P, HSG, 9P, SSI
2103-0092-01
CONT, P, D, 26-22,AU
0650-1079-01
CABLE ASSY, VM8 TOUCHTRACKER/VI
8000-2672-01
INSTL INSTRS, TT ENHANCED
0649-0006-06
BAG, PLASTIC 12-1/2 X 14X4MIL
8000-2653-01
SYS OPERATOR'S MANUAL, VM16
8000-2654-01
SYS QUICK GUIDE, VM16
8000-1370-02
TTRACKER STRAIN RELIEF INSTR
6003-0108-01
CBL/A, VM16+/TNG, MUX/INTFCE
RPNR00
CBL/A, RS-232, 10', DB9F-DB9M
For Quad Splitter (RVQX7X) with DB9 Connector
These additional parts are required.
PN
Description
2125-0007-02
DB9 Hood
2103-0092-02
DB9 Female contact pins
2103-0092-01
DB9 Male contact pins
2130-0021-01
DB9 Male Connector
2130-0022-01
DB9 Female Connector
WARNING:
!
SHOCK! Disconnect AC Power to
the switch.
CAUTION-Electrostatic Sensitive
!
Device: Follow proper handling
procedures to prevent component
failure.
RCTT16BE VM16 PLUS ENHANCED TOUCH TRACKER
INSTALLATION GUIDE
Installation
Installation Kit
Quantity
1
1
2
2
1
3
16.5
1
1
1
0
1
1
1
1
3
1
1
1
1
1
1
1
1
Quantity
2
5
5
1
1
RISK OF ELECTRIC
Note: Prior to installing the Enhanced T
T
, identify the type of external unit that will
RACKERS
connect to the Enhanced T
applicable. Build any cables that are required.
Refer to the Installation Diagrams starting on
page 3 for specific instructions.
1. Terminate the External Interconnect Module
(EIM) at the end of the SensorNet network. If
more than one Enhanced T
controller will be installed, one T
T
's EIM will be terminated; the other EIM
RACKER
will be unterminated. Refer to the appropriate
wiring diagram for your configuration.
2. Mount each EIM on a wall or other surface
within 3m (10 feet) of the Touch Tracker
controller.
3. Connect the power transformer and SensorNet
cable to J3 on each EIM. If two Touch Trackers
will be installed, connect the SensorNet cable
from the first EIM to the second EIM.
4. Depending on the external unit that will be
attached to your system, connect the
appropriate cable to the DB9 connector on the
EIM. Refer to the appropriate wiring diagram for
additional details.
5. Connect the data cable from J1 on the Primary
T
T
OUCH
RACKER
external unit. Refer to the appropriate wiring
diagram for additional details.
6. Connect the modular cable from J2 on each
EIM to the T
OUCH
7. Connect the SensorNet cable from the dome to
the first EIM. Refer to the appropriate wiring
diagram for additional details.
8. Plug in the power transformer into a grounded,
3-wire receptacle.
Note: If the keypad and backlighting do not
illuminate when power is applied, unplug each
power transformer and repeat steps 3 through 8.
Depending on system configuration, it may take up
to 2 minutes for the Enhanced T
come completely online.
Continue with Configuring the External Device.
2 of 15
OUCH
T
, if
OUCH
RACKER
T
OUCH
RACKER
OUCH
's EIM to the remote port on the
T
controller.
RACKER
T
OUCH
RACKER
8000-2672-01, REV. D1
to
Advertisement
Table of Contents
