T
OUCH
1
PARTS REQUIRED
AD T
T
16 Installation Kit:
OUCH
RACKER
Part Number 0351-0474-06
Description
Modular cable assy
Screw, M2.9x9.5
Anchor, 4-8x.750
Screw, #8x1
Conn, 1x5pos
Lug, 22-16AWG
Cable, 3-cond, 18AWG
Interconnect box
Multiplexer cable assy
Hood, D-Sub, 9pos, cable
Conn, D-Sub, plug, hsg, 9pos
Contact, pin, D-Sub, 22-26 AWG
Installation Procedures
1.
Terminate the external interconnect module (EIM) at
the end of the SensorNet network. See the diagram on
page 2.
For more information on the SensorNet network, refer
to the SensorNet Network Guide (PN 8000-0970-01).
2.
Mount each EIM on a wall or other surface within 3m
(10') of the T
T
OUCH
RACKER
3.
Connect the power transformer and SensorNet cable to
J3 on each EIM.
4.
Wire the DB9 connector to the data cable. If you are
using a multiplexer with a DB25 connector, refer to the
illustration on page 2. If you are using a multiplexer with
a RJ11 connector, refer to the illustration on page 3.
5.
Connect the data cable from J1 on the main T
T
EIM to the Remote port at the rear panel of
RACKER
the multiplexer.
6.
Connect the modular cable from J2 on EIM to the
T
T
controller.
OUCH
RACKER
7.
Connect the SensorNet cable from the dome to the
terminated EIM.
8.
Plug each power transformer into a grounded, 3 wire
receptacle.
NOTE: If the keypad and backlighting do not illuminate
when power is applied, unplug each power transformer
and repeat steps 3 through 8.
9.
From the T
T
OUCH
RACKER
to configure the software for the multiplexer.
10. Using the Tracker Ball, page down the screen to
the Config Devices menu option.
11. Press the zoom/focus button to select the
Config Devices menu option.
8000-0982-02, Rev. C
T
with Multiplexer
RACKER
Qty.
Part No.
4.3m
6003-0047-01
1
5899-0004-102
2
2880-0083-01
2
2816-7634-44
1
2109-0254-04
3
2141-0002
5m
6002-0024-01
1
0300-1000-01
1
0650-1079-01
1
2125-0007-02
1
2130-0021-01
1
2103-0092-01
controller.
OUCH
controller, press Menu
AD T
Installation Instructions
!
WARNING Shock Hazard!
Disconnect AC Power to the Switch.
!
CAUTION static sensitive
components!
Follow proper handling procedures
to prevent component failure.
Press Next to the select the appropriate device
12.
for this installation. See the example screen
below.
Device = Mux
= POSEM
13. Press Menu to select the device configuration and
return to the Camera Control mode.
14. To configure the T
OUCH
primary or secondary unit, page down the screen to the
Tog Primary/2nd menu option.
15. Press the zoom/focus button to select the
Tog Primary/2nd menu option.
16. Press Next to toggle between using the T
T
controller as the primary (Main) unit for the
RACKER
SensorNet polling and alarm monitoring or as the
secondary (Call) unit with limited user functionality.
17. Press Menu to reset the T
a primary or secondary unit. The controller will reboot
to the Camera Control Mode.
T
®
16
OUCH
RACKER
16
T
controller as a
RACKER
OUCH
T
controller as
OUCH
RACKER
Installation Instructions