American Dynamics AD2091 Installation Instructions Manual
Code converter
Hide thumbs
Also See for AD2091:
- Specifications (2 pages) ,
- Specifications (2 pages) ,
- Information sheet (4 pages)
Table of Contents
Advertisement
2091 Megapower
Code Converter
Installation Instructions
This Code Converter is for use with 1024 Switching Systems in which one or two 1024 Megapower "brains" are employed. It can
also be used with 1995A, 1995B, and 1995C Megapower CPUs. The Code Converter converts data on the High Speed Data line
to either Control Code used by American Dynamics Receiver Drivers or to RS-232 code which can be sent over networks and
then converted to Control Code using a 1983. The Code Converter contains 64 Control Code outputs and indicators for both
power and valid code that is being received from the Megapower CPUs via the data lines.
Advertisement
Table of Contents
Related Manuals for American Dynamics AD2091
Summary of Contents for American Dynamics AD2091
-
Page 1: Installation Instructions
1995A, 1995B, and 1995C Megapower CPUs. The Code Converter converts data on the High Speed Data line to either Control Code used by American Dynamics Receiver Drivers or to RS-232 code which can be sent over networks and then converted to Control Code using a 1983. - Page 2 The software/firmware furnished with this equipment is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software/firmware is furnished to the purchaser under a license for use on a single system. Information furnished by SENSORMATIC is believed to be accurate and reliable.
- Page 3 The installation of this product should be made by qualified service personnel and should conform to all local codes. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVERS (OR BACK) . NO USER-SERVICEABLE PARTS INSIDE.
-
Page 5: Table Of Contents
Table of Contents Description... 1 Features ... 1 Installation... 1 Mounting... 1 Connections Data Line Connection ... 2 Manchester Code Line Connections ... 2 Powering Up ... 3 Receivers... 3 RS-232 Output ... 4 Baud Rate Selection... 4 Filter Selection ... 4 Typical System Connections... -
Page 7: Description
The 2091 also filters camera switching information for monitors 1-8, when used with the American Dynamics' 1631 Switcher Follower. The 2091 unit provides for 64 code outputs in four groups of 16. The codes provide for controlling pan/tilt, lens, zoom, focus, and iris;... -
Page 8: Connections
When all lines have been connected, insert the 12-pin connectors into the rear panel mating connectors. See Figure 2. B W S B W S B W S B W S Figure 1 - Control Code Generator Rear Panel Table 1 CAMERA SELECT GROUP... -
Page 9: Powering Up
Figure 2 - 12-pin CONTROL CODE Connector Receivers are controlled by Control Code signals received from the code generator/distributor via code lines or other simplex communication links such as phone, laser, microwave, radio, etc. Code lines are NEC Class 2, low voltage circuits. Where local codes permit, installation conduit is not required. -
Page 10: Rs-232 Output
RS-232 OUTPUT and BAUD RATE SELECTION RS-232 OUTPUT The 2091 can also be configured to convert the Data Line input to RS-232 code which can be sent to receivers via a modem or a 1983CS536, RS-232 to Control Code converter, or connected directly to a 1640 “S”... - Page 11 APPENDIX...
-
Page 13: Typical System Connections
NOTE : THESE CONNECTIONS ARE TYPICAL OF ONE RECEIVER. UP TO THREE RECEIVERS MAY BE CONNECTED IN A DAISY CHAIN CONFIGURATION FROM EACH CODE OUTPUT. TYPICAL SYSTEM CONNECTIONS 2091 CODE GENERATOR/DISTRIBUTOR 18 AWG SHIELDED TWISTED PAIR BELDEN 8760 OR EQUIVALENT... -
Page 15: Declaration Of Conformity
93/68/EEC, and the EMC Directive, 89/339/EEC as amended by 93/68/EEC. Pearl River, NY, USA 15 December, 2000 Harold D. Johnson, Ph.D. Director of Engineering 7, rue Alexis de Tocqueville, Parc de Haute Technologie, 92183 ANTONY CEDEX MegaPower Code Converter AD2091-1 European Contact: Sensormatic France S.A. - Page 16 SPECIFICATIONS: Input: AD2091 AD2091-1 230 VAC, 50/60 Hz, 40 mA, EU Compliance Mounting: Surface Mount or Rack Mount Weight: 7.0 lbs. Finish: Shadow Gray Size: 17 " W x 7.75 " D x 3 .5" H 8000-1825-01, Revision A December,2000...