Page 2
Products, LLC brands and product names are trademarks or registered trademarks of their respective companies. ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic...
You may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacific Standard Time.
Page 4
The Stinger Spot carries a 1 year (365 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at www.adj. com. All returned service items whether under warranty or not, must be freight pre-paid and accom- pany a return authorization (R.A.) number.
A. Objects have fallen, or liquid has been spilled into the applicance. B. The applicance has been exposed to rain or water. C. The applicance does not appear to operate normally or exhibits a marked change in perfor- mance. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 5...
Page 6
Be sure this fixture is kept at least 3.3 feet (0.5m) away from any flammable materials, such as deco- rations. Always use an install an appropriately rated safety cable to prevent accidental damage and/ or injury in the event the clamp fails. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 6...
Page 7
Insert the end in the carabine and tighten the safety screw. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 7...
Page 8
Stinger Spot DMX Set Up Power Supply: The ADJ Stinger Spot contains an automatic voltage switch, which will auto sense the voltage when it is plugged into the power source. With this switch there is no need to worry about the correct power voltage, this unit can be plugged in anywhere.
Page 9
XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior. 5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans- mission in place of 3-pin.
Page 10
Stinger Spot System Menu Primary Mode ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 10...
NOTE: In a primary/secondary configuration, you can set one fixture to “PRI” and then set the next fixture to “SEC2”, the fixtures will now have contrasting movements to each other. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 11...
Page 12
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to keep the LED display on at all time, or “OFF” to set the LED display to switch off after 10 seconds. 3. Press ENTER to confirm. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 12...
Page 13
RSET - Use this function to reset the unit. 1. Press the MENU button until “RSET” is displayed, and press ENTER. 2. The fixture will now reset to default factory settings. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 13...
Page 14
“OCOL” is displayed. Press ENTER. 2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 14...
1. Press the MENU button until “SHND” is displayed, and press ENTER. 2. Press the UP or DOWN buttons until you find your desired show, and press ENTER. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 15...
4. On the secondary units, press the MENU button until “SCND” is displayed, and press ENTER. Choose either “Sec1” or “Sec2” and press ENTER. See the System Menu section for more infor- mation. 5. The secondary units will now follow the primary unit. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 16...
Unit does not respond to sound; 1. Low frequencies (bass) should cause the unit to react to sound. Tapping on the microphone, quiet or high pitched sounds may not activate the unit. ADJ Products, LLC - www.adj.com - Stinger Spot User Manual Page 23...
ADJ Products, LLC factory unless prior written authorization was issued to pur- chaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruc- tion manual.