The Signal Select Menu; Using The Service Mode; Entering Into The Service Mode - Sony VPD-LE100 Service Manual

The SET SETTING Menu/The SIGNAL SELECT Menu
POWER SAVING
OFF: The power saving function does not operate.
ON: The projector goes into the power saving mode
and the lamp for light source turns off if no signal
is input for about 10 minutes.
The power saving mode is canceled when a signal
is input or any key is pressed.
SIRCS RECEIVER
Selects the remote control detectors to be activated.
Change the setting if the wireless Remote Commander
does not work properly due to the influence of the
fluorescent lamp, etc.
FRONT & REAR: Activates both the front and rear
detectors.
FRONT: Activates the front detector only.
REAR: Activates the rear detector only.
OFF: Activates neither the front nor rear detector.
Note
When set to OFF, the wireless Remote Commander
does not function. Use the keys on the control panel or
the wired Remote Commander.
GROUP INDEX
Groups multiple projectors or switchers to operate
them simultaneously.
You can set the group index number to the desired
number between 1 and 99.
For details on the group index, see page 26.
DEVICE INDEX
Displays the index number set with the DEVICE
INDEX switches on the rear of the projector. You can
check the device index number but cannot set it with
this menu.
For details on setting the number, see page 26.
C. (cinema) BLACK
Switches the lamp wattage during projection.
OFF: Normal wattage.
ON: Enhances the black by reducing the lamp
wattage.
36
The SIGNAL SELECT
Menu
The SIGNAL SELECT menu is used for selecting the
input signal.
Depending on the interface board installed in the
projector, some items may not be displayed in the
menu. (The following display shows an example.)
SIGNAL SELECT INPUT-A
INPUT-A: DTV-GBR
INPUT-B: DTV-GBR
INPUT-C: DTV-GBR
INPUT-D: 1080/60I
INPUT-A
Selects the signal input from the INPUT A connectors.
COMPUTER: Inputs the signal from a computer or
the RGB signal for a still picture.
COMPONENT: Inputs the component signal.
DTV-YP P : Inputs the DTV (YP P ) or HDTV
B R B R
(YP P ) signal.
B R
DTV-GBR: Inputs the DTV (GBR) or HDTV
(GBR) signal.
Note
When the PC-3000 Signal Interface Switcher is
connected to the INPUT A connectors, you cannot
select the item.
INPUT-B
Selects the input signal from the connectors on the
optional IFB-12A interface board installed in the
INPUT B section.
COMPUTER: Inputs the signal from a computer or
the RGB signal for a still picture.
COMPONENT: Inputs the component signal.
DTV-YP P : Inputs the DTV (YP P ) or HDTV
B R B R
(YP P ) signal.
B R
DTV-GBR: Inputs the DTV (GBR) or HDTV
(GBR) signal.
VIDEO: Inputs the composite video signal.
S-VIDEO: Inputs the S video signal.
Note
This item is not displayed when the optional interface
board other than the IFB-12A is installed in the INPUT
B section, or when the output mode is selected on the
IFB-12A.
INPUT-C
Selects the input signal from the connectors on the
optional IFB-12A interface board installed in the
INPUT C section.
COMPUTER: Inputs the signal from a computer or
the RGB signal for a still picture.
COMPONENT: Inputs the component signal.
DTV-YP P : Inputs the DTV (YP P ) or HDTV
B R B R
(YP P ) signal.
B R
DTV-GBR: Inputs the DTV (GBR) or HDTV
(GBR) signal.
VIDEO: Inputs the composite video signal.
S-VIDEO: Inputs the S video signal.
Note
This item is not displayed when the optional interface
board other than the IFB-12A is installed in the INPUT
C section.
INPUT-D
Selects the type of the HDTV signal (1080/60I, 1080/
50I or 1080/24PsF) input from the connectors on the
optional IFB-LE100 interface board installed in the
INPUT D section.
Note
When inputting the 1035/60I signal to the IFB-LE100,
select 1080/60I.
The SIGNAL SELECT Menu/Using the SERVICE MODE
Using the SERVICE
MODE
There are three menus in the SERVICE MODE:
INFORMATION, SERVICE SETTING, and W/B
ADJUST menus.
Follow the steps below for entering into the SERVICE
MODE. You can enter into the SERVICE MODE even
if the projector is in standby mode.
Confirm that the menu is not displayed on the screen.
Note
Be sure to set STATUS in the SET SETTING menu to
ON. If it is set to OFF, you cannot enter into the
SERVICE MODE.

Entering into the SERVICE MODE

Operation when the projector is on
1
Press the keys in the following order:
ENTER t ENTER t M t m t ENTER
The following screen appears.
Do you wish to enter
into the SERVICE MODE?
YES:
NO:
2
Press the M key.
The projector enters into the SERVICE MODE.
3
Press the MENU key.
The SERVICE MODE select menu appears. When
the projector enters into the SERVICE MODE, "S"
appears on the upper-left corner of the screen.
S INFORMATION INPUT-A
SER. No.: X X X X X
fH: 1 5 . 7 kHz
fV: 1 2 0 . 0 Hz
SYNC: CPOS/– /–
ROM VER.: 1 . 0 0
OPERATION TIMER: 0 0 1 2 3 h
LAMP TIMER: 0 0 1 2 3 h
(continued)
37