Configuration And Function - TDK-Lambda SWS-L Series Manual

SWS
600L, 1000L
Please pay extra attention to the wiring. Incorrect connection
will damage the power supply.
Front Panel Explanation
SWS600L
⑤ ⑥ ④
L N
② ① ③
SWS1000L
②
N
L
⑤ ⑥ ④
① V.ADJ : Output voltage adjustment trimmer.
(The output voltage rises when a trimmer is turned clockwise.)
② ON : Output (Power on) indication LED
(The indicator turns on when the power supply output is in
normal operating condition.)
③ CN1, CN2, CN3 : Remote sensing, ON/OFF control signal,
current balance signal, power fail alarm, auxiliary output,
output voltage external control signal. (Refer to 1-2.)
④ : Protective earth (Frame ground), M4 screw.
(SWS1000L: M4 screw x 2)
⑤ AC input terminal L : Live line (Fuse in line), M4 screw.
⑥ AC input terminal N : Neutral line, M4 screw.
⑦ + : + Output terminal
(SWS600L: M5 screw x 2 / SWS1000L:φ9hall, M4 tapped hall x 2)
⑧ - : - Output terminal
(SWS600L: M5 screw x 2 / SWS1000L:φ9hall, M4 tapped hall x 2)
10
2. Terminal Explanation
⑦
⑧
⑦
⑧
①
③
C N1, C N 2 , C N 3 C o n n e c t o r p i n

Configuration and Function

CN1 and CN2 are same pin confi guration and function. They are
connected to each other in this power supply unit. When the pin
of CN1 side is shorted, the same function pins of CN2 side are
also shorted. Please note that the function cannot be separately
set with CN1 and CN2.
Config-
CN1, CN2 Pin No
uration
1 +Vm +OUTPUT VOLTAGE MONITOR
9 10
2 +S +SENSING
7 8
5 6 3 -Vm -OUTPUT VOLTAGE MONITOR
3 4
4 -S -SENSING
1 2
5 N.C. NO CONNECTION
CN1
6 PC CURRENT BALANCE
9 10
7 8
7 PV ADJUSTMENT OF OUTPUT VOLTAGE
5 6
8 COM GROUND FOR PC AND PV SIGNAL
3 4
1 2
9 CNT2 REMOTE ON/OFF (2)
CN2
10 TOG GROUND FOR CNT2
Config-
CN3 Pin No
uration
1 COM GROUND FOR PC AND PV SIGNAL
2 COM GROUND FOR PC AND PV SIGNAL
3 AUX AUXILIARY OUTPUT (12V 0.1A)
7 8
5 6
4 CNT1 REMOTE ON/OFF (1)
3 4
5 G2 GROUND FOR AUX AND CNT1
1 2
CN3
6 G2 GROUND FOR AUX AND CNT1
7 ALM ALARM
8 G1 ALARM GROUND
CN1, CN2, CN3 Connector & Housing & Terminal Pin
PART DESCRIPTION
PIN HEADER S10B-PHDSS (CN1, CN2)
S8B-PHDSS (CN3)
SOCKET HOUSING PHDR-10VS (CN1, CN2)
PHDR-8VS (CN3)
TERMINAL PINS SPHD-002T-P05 (AWG28~24)
SPHD-001T-P05 (AWG26~22)
HAND CRIMPING YRS-620 (SPHD-002T-P0.5)
TOOL YC-610R (SPHD-001T-P0.5)
・All specifications are subject to change without notice.
Function
Function
PART NAME MANUFACT
J.S.T
J.S.T
J.S.T
J.S.T