Panasonic SC-DM502 Operating Instructions Manual page 18

The sound is interrupted.
≥ The device is out of the 10 m communication range. Place the
Bluetooth device closer to this unit.
®
≥ Remove any interference between this unit and the device.
≥ Other devices that use the 2.4 GHz frequency band, such as
wireless routers, microwaves, cordless phones, etc. are
interfering. Place the Bluetooth
distance it from the other devices.
≥ Select "MODE 1" for stable communication. (l 8)
Messages
The following messages or service numbers may
appear on the unit's display.
"--:--"
≥ You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l 14).
"ADJUST CLOCK"
≥ Clock is not set. Adjust the clock accordingly.
"ADJUST TIMER"
≥ Play timer is not set. Adjust the play timer accordingly.
"AUDIO UNSUPPORTED"
≥ The signal format or frequency is not supported.
≥ This system does not support bitstream signals. Change the
digital audio output setting on the external equipment to PCM.
≥ This system supports sampling frequencies of 32 kHz, 44.1 kHz,
48 kHz and 96 kHz. Select only the supported sampling
frequencies on the connected equipment.
≥ Try connecting the external equipment by using the auxiliary input.
"AUTO OFF"
≥ The unit has been left unused for about 20 minutes and will shut
down within a minute. Press any button to cancel it.
"ERROR"
≥ Incorrect operation is performed. Read the instructions and try
again.
"F " / "F " ("
≥ There is a problem with this unit.
Disconnect the AC mains lead from the mains socket, reconnect it
to the outlet after about 30 seconds. Wait for about 10 seconds,
then turn on the unit. If the problem still persists, disconnect the
AC mains lead and consult your dealer.
"LINKING"
≥ This system is trying to connect to the last connected Bluetooth
device when "BLUETOOTH" is selected.
18
TQBJ2215
device closer to this unit and
®
" stands for a number.)
"NO DEVICE"
≥ The USB device is not inserted correctly. Read the instructions
and try again (l 7).
"NO DISC"
≥ Insert the disc to be played (l 7).
"NO PLAY"
≥ Examine the content. You can only play supported format. (l 19)
≥ The files in the USB device can be corrupted. Format the USB
device and try again.
≥ The unit may have a problem. Turn the unit off and then on again.
"NO PRESET"
≥ There are no preset DAB/DAB+ stations to select. Preset some
channels. (l 10)
"NO SIGNAL"
≥ This station cannot be received. Check your antenna (l 6).
"NOT SUPPORTED"
≥ You have connected an unsupported USB device.
"PLAYERROR"
≥ You played an unsupported file. The system will skip that track
and play the next one.
"READING"
≥ The unit is checking the "CD"/"USB" information. After this display
has disappeared, start operating.
"REMOTE " ("
≥ The remote control and this unit are using different codes. Change
the code on the remote control.
– When "REMOTE 1" is displayed, press and hold [OK] and
[ ] on the remote control for at least 4 seconds.
– When "REMOTE 2" is displayed, press and hold [OK] and
[O SELECT] on the remote control for at least 4 seconds.
"SCAN FAILED"
≥ Stations are not receivable. Check your antenna and try Auto
scanning (l 10).
If "SCAN FAILED" is still displayed find the best signal reception
with the "MANUAL SCAN" tuning function. (l 11)
"SOUND NOT SET" ("
≥ There is no saved setting under the selected sound setting
number. Save the sound settings. (l 14)
"USB OVER CURRENT ERROR"
≥ The USB device is drawing too much power. Disconnect the USB
®
device, turn the unit off and then on again.
≥ Check the connection, it may be caused by a faulty USB cable.
"VBR"
≥ The system cannot show the remaining play time for variable bit
rate (VBR) tracks.
"WAIT"
≥ This is displayed, for example, when this unit is turning off.
" stands for a number.)
" stands for a number.)