Recording A Tv Program - Toshiba D-VR600 Owner's Manual

Recording

Recording a TV program

You can record programs you
watch on TV onto video tapes or
DVDs.
NOTES:
• When recording onto a DVD, it takes
some time from when you press
REC/OTR until recording actually
starts.
Press REC/OTR slightly earlier
before the preferred starting point.
With a video tape, recording starts
almost at the same time as you
press REC/OTR.
• If the erase prevention tab of video
tapes is removed, the tape will eject
when REC/OTR is pressed for re-
cording.
Auto Rewind feature
This unit will automatically rewind the
tape when the tape has ended (except
during OTR and TIMER REC). It will
also eject the tape.
NOTES:
• If the disc space become full, the
recording is stopped and "Disc is
Full" will appear on the screen.
• In the event of a power failure dur-
ing DVD recording including OTR
and TIMER REC, the program can
not be recorded on the disc. When
the power resumes, after the VCR/
DVD is turned on, the set checks the
disc to repair the error which is
caused by a power failure. This
checking process may require a few
minutes to about 1 hour according
to disc condition.
The unauthorized recording, use,
distribution, or revision of television
programs, videotapes, DVDs and
other materials, is prohibited under
the Copyright Laws of the United
States and other countries, and
may subject you to civil and/or
criminal liability.
50
2K70101A_E P44-51
Preparation:
• Connect the AUDIO (L/R)/VIDEO IN jacks on the rear panel (INPUT
1) to the AUDIO (L/R)/VIDEO OUT jacks of the Cable/Satellite box.
• Turn ON the TV and set it to the video input mode.
• Load a recordable DVD or video tape into the unit.
• Press DVD or VCR to select the appropriate mode.
1
Press REC MODE/SPEED to select the re-
cording mode.
The recording mode will appear on the TV
screen and change every time REC MODE/
SPEED is pressed.
VCR recording modes: SP/SLP
DVD recording modes: XP/SP/LP/SLP
SP is the normal recording mode for video tapes. SLP offers 3
times the recording time as SP. For more information on DVD re-
cording modes, see page 48.
2
Press INPUT SELECT to select "LINE1" input position.
"L1" will appear on the display window.
• To record from AUDIO (L/R)/VIDEO IN jacks on the front panel
(INPUT2), select "LINE2" (L2).
L1:
L1(S): AUDIO (L/R)/S-VIDEO IN on the
L2:
L2(S): AUDIO (L/R)/S-VIDEO IN input on the front panel (IN-
DV:
Confirm whether the input source that you used is appeared on
the display window.
3
Select the channel you wish to record on your cable/satellite box.
4
Press REC/OTR.
" " appears on the screen for about 4
seconds and recording will start.
To stop recording
Press STOP to stop recording.
" " will appear on the screen for about 4
seconds.
NOTE:
When recording onto a DVD, even if STOP is pressed during record-
ing, recording does not stop instantly. Recording may continue for as
long as 1 minute.
To stop recording temporarily
Press PAUSE/STILL to avoid recording un-
wanted material.
" " will appear on screen for about 4 sec-
onds.
Press again to resume recording.
NOTES:
• In video recording, the pause function will be released after 5 min-
utes to prevent damaging the video tape. The unit will change to the
STOP mode.
• When recording onto a video tape, you can select a recording chan-
nel in the recording pause mode. (You cannot change a recording
channel in the DVD recording pause mode.)
50
AUDIO (L/R)/VIDEO IN on the
rear panel (INPUT1)
rear panel (INPUT1)
AUDIO (L/R)/VIDEO IN on the front panel (INPUT2)
PUT2)
DV IN on the front panel (see page 69)
08`02`07, 20:45
VCR mode
00 : 00 : 00 SP
DVD mode
SP
P