6 Customizing
This. section. describes. the. various. setting.
option.of.this.BD.player..
If.the.setup.option.is.grayed.out,.it.means.
the. setting. cannot. be. changed. at. the.
current.state.
General Setting
1..Press.SETUP.button.on.the.remote.
control.The.Setup.Menu.appears.
... General Setting ...
System
Language
Playback
Security
Network
Move cursor key to select menu option
then use "OK" key to select
2. Press to.select.an.option,.then.press
.to.access.
3. Press / to.select.a.setup.option.and
press ..
4. Select.the.setting.you.wish.to.change
and press OK to confirm.
- Press to.return.to.the.previous.menu.
[System]
To.change.the.following.system.option.to.
personalize.your.BD.player.
• [Screen Saver]
Turn.On.or.Off.the.screen.saver.mode.
It.helps.to.protect.the.TV.screen.
{.On.}.–.Set.the.screen.saver.active.
after.approximately.10.minutes.with.no.
operation.
-.The.BD.player.will.switch.to.standby.
mode.if.there.is.no.operation.after.the.
screen.saver.is.engaged.for.
approximately.10.minutes.
{.Off.}.–.Turn.off.the.screen.saver.
mode..
• [Disc Auto Playback]
Turn.On.or.Off.the.disc.automatic.
playback.switching.mode.
{On}.–.The.disc.playback.automatically.
after.loading.
{Off}.–.Turn.off.disc.auto.playback.
mode.
• [CEC]
This.player.supports.REGZA-LINK.which.
uses.the.HDMI.CEC.(Consumer.
Electronics Control) protocol. You can
1
Screen Saver
On
Disc Auto Playback
On
CEC
On
Easy Setup
More...
Load Default
More...
Exit
SETUP
use.one.single.remote.control.to.control.
all.REGZA-LINK-compliant.devices.that.
are.connected.through.HDMI.connectors.
{On}.-.Turns.on.REGZA-LINK.features.
-With.CEC.on,.during.TV.standby.with.
the.BD.player.on,.pressing.SETUP,.PLAY/
PAUSE.will..power.on.the.TV.
{Off}.-.Disables.REGZA-LINK.features.
[Easy Setup]
•
Re-configure some settings. It is the same
as "Load Default" of steps 4-8.
Tip:
For setting osd and TV resolution and TV aspect.
• [Load Default]
Reset.all.settings.of.BD.player.to.initial.
default.state.
-.Follow.the.instruction.on.the.TV.screen.
to confirm the default setting operation.
1..Select.Load Default.
2..A.dialogue.box.pops.up.shown.as.
below..Select.OK..
Load Default
Do you want to load default?
3.It.may.take.awhile.when.loading.
default.is.in.progress..Please.wait...
Load Default
Loading default, please wait...
30%
4..TV.will.display.as.follow:
Welcome
to the Toshiba BD Player Setting Wizard.
Some simple settings are suggested before you
begin. You can also access detailed settings
from the Setup Menu.
5. Press OK, enter language setting.
..Press.OK,.enter.language.setting..
Press/ to.select.a.language.option.
Choose
an OSD language before starting.
The language selected will be applied not only
here but also in other OSD windows, menus
etc.
Previous
Cancel
OK
Next
OK
En lish
Français
Español
Next
OK