Sony MZ-DH710 Service Manual page 19

3-5-3. Other setting
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the [VOL+] key once and press the
select the item number 1113 and display as follows.
Display of the remote commander
1113
SS**$$##
adjustment value (hexadecimal)
4. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "**" on the LCD becomes "1A".
5. Press the to write the adjusted value. ($$ blinks and disc
X
mark rotates on the LCD)
6. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "$$"on the LCD becomes "20".
7. Press the key to write the adjusted value. (## blinks and
X
disc mark rotates on the LCD)
8. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "##"on the LCD becomes "94".
9. Press the key to write the adjusted value.
X
10. Press the [VOL+] key once to change the adjustment value of
"**" on the LCD into "1B".
11. Press the key to write the adjusted value. ($$ blinks and
X
disc mark rotates on the LCD)
12. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "$$"on the LCD becomes "F1".
13. Press the key to write the adjusted value. (## blinks and
X
disc mark rotates on the LCD)
14. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of "##"on the LCD becomes "1A".
15. Press the to write the adjusted value.
X
16. Press the key four times and back to the Display Check
x
mode.
3-6. Servo Overall Adjustment
Note1: Be sure to adjustment so that the set is horizontal and the LCD is
Note2: If NG is displayed in the middle of this adjustments, perform "3-2.
key five time to
>
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL--] key to enter the Overall Adjustment mode.
3. Insert the CD adjustment disc (TDYS-1).
4. Put the main unit horizontal so that the LCD becomes upside,
5. Wait until "CD OK" is displayed on the LCD.
6. Insert the MD1/HiMD1 hybrid adjustment disc
7. Put the main unit horizontal so that the LCD becomes upside,
8. Wait until "MD1 OK" is displayed on the LCD.
9. Insert the Hi-MD3 adjustment disc (HMD1GSDJ).
10. Put the main unit horizontal so that the LCD becomes upside,
11. Wait until "HMD3OK" is displayed on the LCD.
12. Eject the disc and close the lid.
13. Put the main unit horizontal so that the LCD becomes upside,
14. Wait until "OfstOK" is displayed on the LCD.
15. Press the
3-7. Resume Clear
Procedure:
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the [VOL+] key once, press the
4. Press the
5. Press the
3-8. Releasing The Test Mode
Note: When the power supply is switched on in the state where all
upside. Unless performed in that state, it is not adjusted correctly.
Initialize The Adjustment Value" and "3-5. Setting The Adjustment
Values" again, then retry this adjustments from step 1.
and press the key.
.
(MDW-74/GA2).
and press the key.
>
and press the [VOL+] key.
and press the [VOL--] key.
key and back to the Display Check mode.
x
[VOL--] key once, press the
>
key twice, press the key three times to select the item
>
number 1933.
key to resume clear.
X
key four times and back to the Display Check
x
mode.
electrical adjustments have not finished, it is displayed on LCD as
"Error EE'' and the usual operation can't be performed. When a
power supply is accidentally turn off in the middle of electrical
adjustments, it is again set as test mode and electrical adjustments
is mode to complete.
MZ-DH710
key once, press the
>
key once, and press the [VOL+]
19