P-334WH 802.11g High Power Wireless Router Quick Start Guide Version 3.60 Edition 1 8/2006 Table of Contents ENGLISH DEUTSCH ESPAÑOL FRANÇAIS ITALIANO SVENSKA 繁體中文...
Overview The P-334WH is an IEEE 802.11b/g wireless broadband router with a four-port 10/100 Mbps switch. The P- 334WH also works as an access point (AP) or a Wi-Fi WAN router that allows you to access the Internet via a wireless WAN connection.
1 Hardware Connections Do the following to make hardware connections for initial setup. WAN Connection Connect your modem to the WAN port using the cable that came with your modem. LAN Connection Connect your computer to a LAN port using the included Ethernet cable. POWER Connection Use the included power adaptor to connect the POWER socket to an appropriate power source.
2 Accessing the Web Configurator 1 Launch your web browser. Enter “192.168.1.1” as the web site address. Note: If the login screen does not display, check your browser’s security settings (see Troubleshooting for details) or make sure your computer is set to receive an IP address dynamically (see Set Up Your Computer’s IP 2 The Password window displays.
When the P-334WH is in Access Point or WiFi WAN Router mode, all LAN and WAN ports act as a hub. If you want to configure the operating mode, click Maintenance > Sys OP Mode. See your User’s Guide for more information about the operating modes.
Current screen information will be lost if you click Back. STEP 1: System Information 1 This screen is optional. You can just click Next. • System Name is for identifying the P-334WH. You can enter your computer's "Computer Name". • If you leave the Domain Name blank, the domain name obtained by DHCP from the ISP is used.
Basic(WEP) Security A Enter a unique name to identify the P-334WH in the wireless LAN. B Select Basic(WEP) security. C The P-334WH automatically scans for and selects a channel not in use by a nearby device. The P-334WH and wireless client must use the same channel. D Select 64-bit, 128-bit or 256-bit from the WEP Encryption drop-down list.
Page 9
Extend (WPA-PSK or WPA2-PSK) Security A Enter a unique name to identify the P-334WH in the wireless LAN. B Select WPA-PSK or WPA2-PSK security. C The P-334WH automatically scans for and selects a channel not in use by a nearby device. The P-334WH and wireless client must use the same channel.
Page 10
STEP 3: The wizard attempts to detect which WAN connection type you are using. If the wizard cannot detect a connection type, you must select ONE from the drop-down list box. Check with your ISP to make sure you are using the correct type: 1 Ethernet 2 PPPoE 3 PPTP.
Ethernet Connection A Select Ethernet as your WAN connection type. B Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to C. Select Use fixed IP address provided by your ISP to give the P-334WH a static IP address. Go to B1. B1 If you select Use fixed IP address provided by your ISP, enter a WAN IP address, WAN IP Subnet Mask and the neighboring device’s IP address given by your ISP.
PPPoE Connection A Select PPPoE as your WAN connection type. B Type a Service Name (optional), User Name and Password. C Select Get automatically from your ISP if your ISP did not assign you a fixed IP address. Skip to D. Select Use fixed IP address provided by your ISP to give the P-334WH a static IP address.
PPTP Connection A Select PPTP as your WAN connection type. B Type a User Name and Password. C Select Get automatically from ISP if your ISP did not assign you a fixed PPTP IP address. Or select Use fixed IP address to give the P-334WH a fixed, unique PPTP IP address and subnet mask. D Type a PPTP Server IP Address.
Internet Access Setup Complete If you have any Internet access problems, follow the on-screen instructions. Click Finish to complete the wizard setup. Troubleshooting 1 If you cannot access the web configurator using Internet Explorer in Windows XP or Windows Server 2003, make sure you allow pop-up windows, JavaScripts and Java permissions or set the Internet security level lower than High in Internet Explorer (in Internet Explorer, click Tools >...
Page 18
1 In Windows XP, click start, Control Panel. In Windows 2000/NT, click Start, Settings, Control Panel. 2 In Windows XP, click Network Connections. In Windows 2000/NT, click Network and Dial-up Connections. 3 Right-click Local Area Connection and then click Properties. 4 Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and click Properties.
Übersicht Der P-334WH ist ein drahtloser IEEE 802.11b/g-Breitbandrouter mit einem eingebauten 10/100-Mbps-Switch mit vier Anschlüssen. Der P-334WH kann auch als Access Point (AP) oder Wi-Fi WAN-Router verwendet werden, mit dem Sie über eine WAN-Verbindung auf das Internet zugreifen können. Tabelle 1 Daten zum Internetkonto Die WAN IP-Adresse Ihres Geräts (wenn vorhanden): ______________ DNS Server IP-Adresse (wenn vorhanden): Primär _____________, Sekundär ______________ Verbindungstyp:...
Page 20
1 Anschließen der Hardware Bei der Erstinstallation müssen die folgenden Hardwareverbindungen hergestellt werden. Herstellen der WAN-Verbindung Schließen Sie Ihr Modem mit dem mitgelieferten Kabel an den WAN-Anschluss an. Herstellen der LAN-Verbindung Schließen Sie Ihren Computer mit dem mitgelieferten Ethernet-Kabel an einen LAN-Anschluss an. Anschließen an das Stromnetz Verbinden Sie den Netzanschluss des Geräts (POWER) mit dem mitgelieferten Netzadapter mit einer geeigneten Stromquelle.
Page 21
Die LED-Anzeigen Prüfen Sie die LEDs auf dem Gerät. Wenn Sie das Gerät an das Stromnetz anschließen, beginnt die LED-Anzeige PWR zu blinken. Wenn es bereit ist, hört sie auf zu blinken und leuchtet stetig. Die LED-Anzeigen LAN, WAN und WLAN beginnen zu leuchten, wenn die entsprechenden Verbindungen bestehen.
Page 22
3 Operating Mode (Betriebsmodus) Der P-334WH unterstützt drei Betriebsmodi: Router, Access Point und WiFi WAN Router. Router (Standard): Wählen Sie diesen Modus, wenn der P-334WH mit einem DSL/Kabel-Breitbandmodem verbunden ist. Durch NAT können alle Computer des LAN mit derselben öffentlichen IP-Adresse auf das Internet zugreifen.
Page 23
4 Verbindungsassistent-Setup Hinweis: Der Verbindungsassistent wird nur dann zum Einrichten des Internetzugriffs verwendet, wenn der P-334WH im Router-Modus verwendet wird. Wenn sich der P-334WH im Access Point- oder WiFi WAN Router-Modus befindet, setzt der Assistent den Betriebsmodus auf Router (die Standardeinstellung) zurück. 1 Melden Sie sich beim Web-Konfigurator an, klicken Sie auf Go to Wizard setup (Zum Assistenten- Setup), und wählen Sie aus dem Listenfeld eine...
SCHRITT 1: Systemdaten 1 Dieses Fenster ist optional. Sie können einfach auf Next (Weiter) klicken. Der System Name (Systemname) wird für die Identifikation des P-334WH benötigt. Geben Sie den Namen des Computers "Computername" ein Wenn Sie das Feld Domain Name (Domainname) frei lassen, wird der Domainname verwendet, der vom DHCP des Internetdienstanbieters vorgege- ben ist.
Page 25
Basis-Sicherheit (WEP) A Geben Sie einen Namen ein, mit dem der P-334WH im Wireless-LAN eindeutig identifiziert wird. B Wählen Sie die Sicherheitsstufe Basic (WEP) (Basis (WEP)). C Der P-334WH sucht automatisch nach einem Kanal, der nicht von einem Gerät in der Umgebung verwendet wird.
Page 26
Erweitern (WPA-PSK) oder WPA2-PSK-Si A Geben Sie einen Namen ein, mit dem der P-334WH im Wireless-LAN eindeutig identifiziert wird. B Wählen Sie die Sicherheit WPA-PSK oder WPA2-PSK. C Der P-334WH sucht automatisch nach einem Kanal, der nicht von einem Gerät in der Umgebung verwendet wird.
Page 27
SCHRITT 3: Der Assistent versucht zu ermitteln, welche Art von WAN-Verbindung Sie verwenden. Wenn der Assistent keinen Verbindungstyp erkennen kann, müssen Sie aus dem Listenfeld EINEN auswählen. Prüfen Sie bei Ihrem Internetdienstanbieter, ob Sie den richtigen Typ verwenden: 1 Ethernet 2 PPPoE 3 PPTP Hinweis: Wenn Ihnen Zugangseinstellungen für das Internet vorgegeben wurden, geben Sie diese in...
Page 28
Ethernet-Verbindung A Wählen Sie als Ihren WAN-Verbindungstyp Ethernet. B Wählen Sie Get automatically from your ISP (Automatisch vom Internetdienstanbieter laden), wenn Sie von Ihrem Internetdienstanbieter keine feste IP-Adresse zugewiesen bekommen haben. Weiter mit C. Oder Wählen Sie Use fixed IP address provided by your ISP (Vom Internetdienstanbieter vorgegebene feste IP- Adresse verwenden), um dem P-334WH eine feste und eindeutige IP-Adresse zu geben.
Page 30
PPPoE-Verbindung A Wählen Sie als Ihren WAN-Verbindungstyp PPPoE. B Geben Sie Service Name (Servicename) (optional), User Name (Benutzername) und Password (Passwort) ein. C Wählen Sie Get automatically from your ISP (Automatisch vom Internetdienstanbieter laden), wenn Sie von Ihrem Internetdienstanbieter keine feste IP-Adresse zugewiesen bekommen haben. Weiter mit D. Oder Wählen Sie Use fixed IP address provided by your ISP (Vom Internetdienstanbieter vorgegebene feste IP- Adresse verwenden), um dem P-334WH eine feste und eindeutige IP-Adresse zu geben.
Page 32
PPTP-Verbindung A Wählen Sie als Ihren WAN-Verbindungstyp PPTP. B Geben Sie User Name (Benutzername) und Password (Passwort) ein. C Wählen Sie Get automatically from your ISP (Automatisch vom Internetdienstanbieter laden), wenn Sie von Ihrem Internetdienstanbieter keine feste PPTP IP-Adresse zugewiesen bekommen haben. Oder wählen Sie Use fixed IP address (Feste IP-Adresse verwenden), um dem P-334WH eine feste und eideutige PPTP IP-Adresse sowie Subnet-Mask zuzuweisen.
Page 34
Einrichten des Internetzugangs fertig stellen Wenn beim Zugriff auf das Internet Probleme auftreten sollten, befolgen Sie die Anweisungen auf dem Bildschirm. Klicken Sie auf Finish (Fertig stellen), um den Setup- Assistenten abzuschließen. Problembeseitigung 1 Wenn Sie mit dem Internet Explorer bei Windows XP oder Windows Server 2003 nicht auf den Web- Konfigurator zugreifen können, stellen Sie sicher, dass alle Pop-Up-Fenster, JavaScripts und Java- Einstellungen zugelassen werden, oder dass die Einstellungen für die Internetsicherheit im Internet Explorer nicht die Stufe Hoch haben (klicken Sie beim Internet Explorer auf Extras >...
Page 35
B) Stellen Sie sicher, dass der P-334WH und Ihr Computer dieselben Sicherheitseinstellungen verwenden. Führen Sie die Schritte aus Abschnitt 4 aus. Einrichten der IP-Adresse des Computers In diesem Abschnitt wird beschrieben, wie Sie Ihren Computer einrichten müssen, damit er bei Windows 2000, Windows NT und Windows XP eine IP-Adresse empfangen kann.
Vista previa El P-334WH es un router de banda ancha IEEE 802.11b/g con un switch 10/100 Mbps de cuatro puertos incorporado. El P-334WH también funciona como punto de acceso (PA) o router Wi-Fi WAN que le permite acceder a Internet a través de una conexión WAN inalámbrica. Debe tener una cuenta de Internet ya configurada y la mayor parte de la siguiente información.
Page 37
1 Conexiones del hardware Realice lo siguiente para crear conexiones de hardware para la configuración inicial. Conexión WAN Conecte su módem al puerto “WAN” usando el cable que venía con su módem. Conexión LAN Conecte su ordenador a un puerto "LAN" usando el cable Ethernet incluido. Conexión de ALIMENTACIÓN Utilice el adaptador de corriente incluido para conectar el zócalo POWER (ALIMENTACIÓN) a una fuente de alimentación apropiada.
Page 38
2 Acceso al configurador Web 1 Abra su explorador de web. Introduzca “192.168.1.1” como dirección del sitio web. Nota: Si la pantalla de acceso no aparece, compruebe la configuración de seguridad de su explorador (ver Solución de problemas para más detalles) o compruebe que su ordenador esté ajustado para recibir una dirección IP dinámicamente (ver 2 Aparecerá...
Page 39
WiFi WAN Router: en este modo, el P-334WH funciona como un Router, pero utiliza una conexión WAN inalámbrica a través de un punto de acceso (AP) o router inalámbrico, en lugar de una conexión con cables a través de módem DSL/cable. En este modo, el P-334WH no permite el acceso a la red a clientes inalámbricos (WLAN).
Page 40
1 Tras entrar en el configurador web y hacer clic en Go to Wizard setup (Ir al Asistente para la configuración), elija su idioma en el cuadro de la lista desplegable. Haga clic en Next (Siguiente). Configuración del acceso a Internet Nota: Introduzca la información de acceso a Internet facilitada por su ISP en cada pantalla del asistente y luego haga clic en Next (Siguiente) para continuar o haga clic en Back (Atrás) para regresar a la pantalla anterior.
Page 41
• Seguridad Extend (Extendida) (WPA-PSK o WPA2-PSK): Configura una clave pre-compartida. Elija esta opción sólo si sus clientes inalámbricos soportan WPA-PSK o WPA2-PSK respectivamente. Nota: Los clientes inalámbricos y el P-334WH deben usar el mismo SSID, ID de canal y WPA(2)-PSK (si WPA(2)-PSK está...
Page 42
Seleccione seguridad Básica (WEP) A Introduzca un nombre único para identificar al P-334WH en la LAN inalámbrica. B Seleccione seguridad Básica (WEP). C El P-334WH busca automáticamente y selecciona un canal no en uso por un dispositivo cercano. El P-334WH y el cliente inalámbrico deben usar el mismo ID de canal.
Page 43
Extienda la seguridad (WPA-PSK) o (WPA2-PSK) A Introduzca un nombre único para identificar al P-334WH en la LAN inalámbrica. B Seleccione seguridad WPA-PSK o WPA2-PSK. C El P-334WH busca automáticamente y selecciona un canal no en uso por un dispositivo cercano. El P-334WH y el cliente inalámbrico deben usar el mismo ID de canal.
Page 44
Nota: Si se le ha facilitado una configuración de acceso a Internet, introdúzcala en los campos siguientes. De lo contrario, deje los valores predeterminados y haga clic en Next (Siguiente). Conexión Ethernet A Seleccione Ethernet como tipo de conexión WAN. B Seleccione Get automatically from your ISP (Obtener automáticamente de su ISP) si su ISP no le asignó...
Page 46
Conexión PPPoE A Seleccione PPPoE como tipo de conexión WAN. B Escriba el Service Name (Nombre de servicio) (Opcional), User Name (Nombre de usuario) y Password (Contraseña). C Seleccione Get automatically from your ISP (Obtener automáticamente de su ISP) si su ISP no le asignó una dirección IP fija.
Page 48
Conexión PPTP A Seleccione PPTP como tipo de conexión WAN. B Escriba un User Name (Nombre de usuario) y Password (Contraseña) C Seleccione Get automatically from your ISP (Obtener automáticamente de su ISP) si su ISP no le asignó una dirección IP PPTP fija. O seleccione Use fixed IP address (Utilizar dirección IP fija) para dar al P-334WH una dirección IP PPTP única y fija y una máscara de subred.
Page 50
Configuración del acceso a Internet completada Si tiene algún problema de acceso a Internet, siga las instrucciones en pantalla. Haga clic en Finish (Finalizar) para completar la configuración del asistente. Solución de problemas 1 Si no puede acceder al configurador web utilizando Internet Explorer en Windows XP o Windows Server 2003, asegúrese de tener habilitada la apertura de ventanas emergentes, permisos para JavaScripts y Java o ajuste el nivel de seguridad de Internet a un nivel más bajo que High (Alto) en Internet Explorer (en Internet Explorer, haga clic en Herramientas >...
Page 51
Configurar la dirección IP de su ordenador Esta sección le explica cómo configurar su ordenador para recibir una dirección IP en Windows 2000, Windows NT y Windows XP. Esto asegura que su ordenador pueda conectarse con su P-334WH. 1 En Windows XP, haga clic en Inicio, Panel de control. En Windows 2000/NT, haga clic en Inicio, Configuración, Panel de control.
Présentation Le P-334WH est un routeur large bande sans fil IEEE 802.11b/g équipé d'un commutateur 10/100 Mbps à quatre ports intégré. Le P-334WH fonctionne aussi comme un point d'accès (AP) ou un routeur Wi-Fi WAN vous permettant d'accéder à Internet via une connexion WAN sans fil. Vous devez déjà...
Page 53
1 Connexions matérielles Procédez comme suit pour effectuer les connexions matérielles pour l'installation initiale. Connexion WAN Connectez votre modem au port “WAN” à l'aide du câble fourni avec votre modem. Connexion par réseau local Connectez votre ordinateur à un port "LAN" à l'aide du câble Ethernet fourni. Connexion de l'alimentation Utilisez l’adaptateur d’alimentation fourni pour connecter à...
Page 54
2 Accéder au configurateur Web 1 Lancez votre navigateur web. Entrez “192.168.1.1” comme adresse de site Web. Remarque: Si l'écran de connexion n'apparaît pas, vérifiez les paramètres de sécurité de votre navigateur (voir Dépannage pour plus de détails) ou assurez-vous que votre ordinateur est configuré...
Page 55
Routeur WiFi WAN : Dans ce mode, le P-334WH fonctionne comme un routeur, mais utilise une connexion WAN sans fil via un point d'accès (AP) ou un rouleur sans fil, à la place d'une connexion câblée via un modem DSL/câble. Dans ce mode, le P-334WH ne permet pas au réseau d'accéder aux clients sans fil (WLAN). Point d'accès : Dans ce mode, le P-334WH fonctionne comme un routeur sans fonctionnalités de routage (telles que NAT), pare feu, filtrage de contenu, etc.
Page 56
1 Après vous être connecté au configurateur web et avoir cliqué sur Aller à l'installation de l'assistant, choisissez votre langue dans la liste déroulante. Cliquez sur Next (Suivant). Installation de l'accès à Internet Remarque: Saisissez les informations d'accès à Internet exactement telles qu'elles sont fournies par votre fournisseur d'accès à...
Page 57
• Sécurité de base : WEP (Wired Equivalent Privacy) crypte les trames de données avant de les transmettre sur le réseau sans fil. Plus le cryptage WEP est élevé, meilleure sera la sécurité mais plus le débit sera lent. • Sécurité (WPA-PSK ou WPA2-PSK) étendue : Configurer une clé prépartagée. Choisissez cette option seule- ment si vos clients sans fil supportent respectivement WPA-PSK ou WPA2-PSK.
Page 58
Sécurité de base (WEP) A Saisissez un nom unique pour identifier le P-334WH dans le LAN sans fil. B Sélectionnez la sécurité de base (WEP). C Le P-334WH recherche et sélectionne automatiquement un canal qui n'est pas utilisé par un appareil avoisinant.
Page 59
Sécurité étendue (WPA-PSK ou WPA2-PSK) A Saisissez un nom unique pour identifier le P-334WH dans le LAN sans fil. B Sélectionnez la sécurité WPA-PSK ou WPA2-PSK. C Le P-334WH recherche et sélectionne automatiquement un canal qui n'est pas utilisé par un appareil avoisinant.
Page 60
Remarque: Si vous avez obtenu les paramètres d'accès Internet, saisissez-les dans les champs suivants. Sinon laissez les paramètres par défaut et cliquez simplement sur Next (Suivant). Connexion Ethernet A Sélectionnez Ethernet comme type de connexion WAN. B Sélectionnez Get automatically from your ISP (Obtenir automatiquement de l'ISP) si votre ISP ne vous a pas attribué...
Page 62
Connexion PPPoE A Sélectionnez PPPoE comme étant votre type de connexion WAN. B Tapez un Service Name (nom de service) (optionnel), User Name (nom d'utilisateur) et Password (mot de passe). C Sélectionnez Get automatically from your ISP (Obtenir automatiquement de l'ISP) si votre ISP ne vous a pas attribué...
Page 64
Connexion PPTP A Sélectionnez PPTP comme type de connexion WAN. B Tapez un User Name (nom d'utilisateur) et Password (un mot de passe). C Sélectionnez Get automatically from ISP (Obtenir automatiquement de l'ISP) si votre ISP ne vous a pas attribué...
Page 66
Installation de l'accès à Internet terminée Si vous rencontrez des problèmes pour accéder à Internet, suivez les instructions à l'écran. Cliquez sur Finish (Terminer) pour mettre fin à l'exécution de l'assistant. Dépannage 1 Si vous ne pouvez pas accéder au configurateur web en utilisant Internet Explorer dans Windows XP ou Windows Server 2003, assurez-vous d'avoir autorisé...
Page 67
Paramétrez l'adresse IP de votre ordinateur Cette section vous indique comment paramétrer votre ordinateur pour recevoir une adresse IP dans Windows 2000, Windows NT et Windows XP. Cela assure que votre ordinateur peut communiquer avec votre P-334WH. Dans le guide de l’utilisateur, vous trouverez davantage d’informations sur la configuration de l’adresse IP pour d’autres systèmes d’exploitation Windows et Macintosh.
Cenni generali Il P-334WH è un router broadband wireless IEEE 802.11b/g con uno switch incorporato a quattro porte da 10/ 100 Mbps. Il P-334WH lavora anche come Access Point (AP) o come router Wi-Fi WAN che consente di accedere a Internet tramite una connessione WAN wireless. È...
1 Collegamenti hardware Di seguito sono illustrati i collegamenti hardware per l'installazione iniziale. Collegamento WAN Collegare il modem alla porta “WAN” utilizzando il cavo fornito a corredo con il modem. Collegamento LAN Collegare il computer alla porta "LAN" utilizzando un cavo Ethernet fornito a corredo. Collegamento POWER Utilizzare l'alimentatore incluso per collegare la presa POWER a una sorgente di alimentazione appropriata.
Page 70
2 Accesso allo strumento di configurazione Web 1 Avviare il browser. Immettere 192.168.1.1 nella barra degli indirizzi. Nota: Se non viene visualizzata la schermata di login, controllare le impostazioni di sicurezza del browser (vedere Risoluzione dei problemi per i dettagli) oppure verificare che il computer sia impostato per ricedere dinamicamente un indirizzo IP (vedere computer).
Page 71
WiFi WAN Router: In questa modalità, il P-334WH lavora allo stesso modo di un Router, ma utilizza una connessione WAN wireless tramite un Access Point (AP) o un router wireless, invece di una connessione cablata tramite un modem DSL/via cavo. In questa modalità, il P-334WH non consente l'accesso di rete ai client wireless (WLAN).
Page 72
1 Dopo aver avuto accesso al configuratore Web e fatto clic su Configurazione guidata, scegliere la lingua dall'elenco a discesa. Fare clic su (avanti). Configurazione dell'accesso a Internet Nota: Immettere le informazioni e i parametri Internet esattamente come sono stati forniti dal proprio ISP nelle varie schermate e quindi fare clic su Next (Avanti) per continuare oppure su Back (Indietro) per tornare alla schermata precedente.
Page 73
• Protezione di Base: WEP (Wired Equivalent Privacy) esegue la crittografia dei frame di dati prima di trasmet- terli sulla rete wireless. Maggiore è la crittografia WEP, maggiore è la protezione a costo di una minore velocità di trasferimento dati. •...
Page 74
Protezione Base (WEP) A Immettere un nome univoco per identificare il P-334WH nella LAN wireless. B Selezionare la protezione Base (WEP). C P-334WH cerca e seleziona automaticamente un canale non utilizzato da altri dispositivi nelle vicinanze. P- 334WH il client wireless devono utilizzare lo stesso ID di canale. D Selezionare 64 bit, 128 bit o 256-bit dall'elenco a discesa WEP Encryption (crittografia WEP).
Page 75
Protezione Estesa (WPA-PSK) o (WPA2-PSK) A Immettere un nome univoco per identificare il P-334WH nella LAN wireless. B Scegliere la protezione WPA-PSK o WPA2-PSK. C P-334WH cerca e seleziona automaticamente un canale non utilizzato da altri dispositivi nelle vicinanze. P- 334WH il client wireless devono utilizzare lo stesso ID di canale.
Page 76
Nota: Se sono state fornite le impostazioni di accesso Internet, immettere i campi seguenti. In caso contrario, lasciare le impostazioni predefinite e fare solo clic su Next (Avanti). Collegamento Ethernet A Scegliere Ethernet come tipo di connessione WAN. B Selezionare Get automatically from your ISP (Ottieni automaticamente dall'ISP) se l'ISP non ha assegnato un indirizzo IP statico.
Page 78
Collegamento PPPoE A Selezionare PPPoE utilizzando il tipo di connessione WAN. B Immettere Nome del servizio (opzionale), Nome utente e Password. C Selezionare Get automatically from your ISP (Ottieni automaticamente dall'ISP) se l'ISP non ha assegnato un indirizzo IP statico. Passare alla sezione D. Oppure Selezionare Use fixed IP address provided by your ISP (Utilizza indirizzo IP fisso fornito dall'ISP) per fornire al P-334WH un indirizzo IP statico univoco.
Page 80
Collegamento PPTP A Selezionare PPTP utilizzando il tipo di connessione WAN. B Immettere Nome utente e Password C Selezionare Ottieni automaticamente dall'ISP se l'ISP non ha assegnato un indirizzo IP PPTP statico. Oppure selezionare Utilizza indirizzo IP fisso per fornire al P-334WH un indirizzo IP statico univoco. D Immettere un indirizzo IP del server PPTP E Immettere ID connessione/Nome (se forniti) F Selezionare Get automatically from your ISP (Ottieni automaticamente dall'ISP) se l'ISP non ha...
La configurazione dell'accesso a Internet viene completata Se si verificano problemi con l'accesso a Internet, seguire le istruzioni visualizzate a shermo. Fare clic su Finish (fine) per completare la configurazione guidata. Risoluzione dei problemi 1 Se non si riesce ad accedere allo strumento di configurazione Web utilizzando Internet Explorer in Windows XP o Windows Server 2003, verificare che le finestre pop-up windows, JavaScript e Java siano autorizzate oppure impostare il livello di protezione Internet a un grado più...
Page 83
Impostare l'indirizzo IP del computer Questa sezione spiega come configurare il computer per ricevere un indirizzo IP in Windows 2000, Windows NT e Windows XP. In questo modo ci si assicura che il computer possa comunicare con lo P-334WH. 1 In Windows XP, fare clic su Start, Pannello di controllo. In Windows 2000/NT, fare clic su Start, Impostazioni, Pannello di controllo.
Översikt P-334WH är en IEEE 802.11b/g trådlös bredbandsrouter med en inbyggd fyraportars 10/100 Mbps-switch. P- 334WH fungerar även som en åtkomstpunkt (AP) eller en Wi-Fi WAN-router som ger dig åtkomst till Internet via en trådlös WAN-anslutning. Du behöver ha ett Internet-konto redan konfigurerat och ha tillgång till följande information. Table 1 Information om Internet-konto Enhetens WAN IP-adress (om du fått sådan): ______________ IP-adress för DNS-server (om du fått sådan): Primär _____________, Sekundär ______________...
Page 85
1 Maskinvaruanslutningar Gör följande för att utföra maskinvaruanslutningar för inledande inställning. WAN-anslutning Anslut ditt modem till “WAN”-porten med sladden som medföljde ditt modem. LAN-anslutning Anslut datorn till en "LAN"-port med den medföljande Ethernet-sladden. Strömanslutning Använd den medföljande strömadaptern för att ansluta uttaget POWER (ström) till en lämplig strömkälla. Indikatorlamporna Titta på...
Page 86
2 Åtkomst till webbkonfigurator 1 Starta din webbläsare. Ange “192.168.1.1” som webbplatsadress. Note: Om inloggningsskärmen inte visas, kontrolla webbläsarens säkerhetsinställningar (se ) eller kontrollera att din dator är inställd på att ta emot en IP-adress dynamiskt (se detaljer in datorns IP-adress).
Page 87
Åtkomstpunkt: I detta läge fungerar P-334WH som en router utan routing-funktioner (som t ex NAT), brandvägg, innehållsfiltrering osv. När P-334WH befinner sig i läget Access Point (åtkomstpunkt) eller WiFi WAN Router, fungerar alla LAN- och WAN-portar som en hubb. Om du vill konfigurer användningsläget, klicka på Maintenance (underhåll) > Sys OP Mode (Sys Op-läge). Se din bruksanvisning för mer information om användningslägena.
Page 88
Inställning av Internet-åtkomst Note: Ange informationen för Internet-åtkomst exakt som du fått den av din ISP på varje guideskärm och klicka sedan på Next (nästa) för att fortsätta eller klicka på Back (bakåt) för att återgå till föregående skärm. Aktuell skärminformation går förlorad om du klickar på Back (bakåt). STEG 1: Systeminformation 1 Denna skärm är valfri.
Page 89
Auto eller ingen trådlös säkerhet A Ange ett unikt namn för att identifiera P-334WH i det trådlösa LAN. B Välj en nivå för trådlös säkerhet. Välj Auto eller None (ingen). C P-334WH söker automatiskt efter och väljer en kanal som inte används av en närliggande enhet. P-334WH och den trådlösa klienten måste använda samma kanal.
Page 90
Utökad (WPA-PSK eller WPA2-PSK) säkerhet A Ange ett unikt namn för att identifiera P-334WH i det trådlösa LAN. B Välj WPA-PSK eller WPA2-PSK säkerhet. C P-334WH söker automatiskt efter och väljer en kanal som inte används av en närliggande enhet. P-334WH och den trådlösa klienten måste använda samma kanal.
Page 91
STEG 3: Guiden försöker detektera den WAN-anslutningstyp du använder. Om guiden inte detekterar en anslutningstyp, måste du välja ONE (en) från rullgardinsrutan. Kontrollera med din ISP så att du verkligen använder rätt typ: 1 Ethernet 2 PPPoE 3 PPTP. Note: Om du har fått Internet-åtkomstinställningar, ange dem i följande fält. I annat fall, låt standardinställningarna stå...
Page 92
Ethernet-anslutning A Välj Ethernet som WAN-anslutningstyp. B Välj Get automatically from your ISP (hämta automatiskt från ISP) om din ISP inte har tilldelat dig en fast IP- adress. Gå direkt till C. Eller Välj Use fixed IP address provided by your ISP (välj fast IP-adress som tillhandahållits av ISP) för att ge P- 334WH en fast, unik IP-adress.
Page 94
PPPoE-anslutning A Välj PPPoE som WAN-anslutningstyp. B Ange ett Service Name (tjänstenamn - tillval), User Name (användarnamn) och Password (lösenord). C Välj Get automatically from your ISP (hämta automatiskt från ISP) om din ISP inte har tilldelat dig en fast IP- adress.
Page 96
PPTP-anslutning A Välj PPTP som WAN-anslutningstyp. B Ange User Name (användarnamn) och Password (lösenord). C Välj Get automatically from your ISP (hämta automatiskt från ISP) om din ISP inte har tilldelat dig en fast PPTP IP-adress. Eller välj Use fixed IP address (använd fast IP-adress) för att ge P-334WH en fast, unik PPTP IP-adress och subnetmask.
Page 98
Inställning av Internet-åtkomst slutförd Om du har åtkomstproblem till Internet, följ instruktionerna på skärmen. Klicka på Finish(slutför) för att slutföra installationen. Felsökning 1 Om du inte kan öppna webbkonfiguratorn med Internet Explorer i Windows XP eller Windows Server 2003, kontrollera att du tillåter pop-up-fönster, JavaScripts och Java-tillstånd eller ställ in en lägre Internet- säkerhetsnivå...
Page 99
Ställa in datorns IP-adress I detta avsnitt beskrivs hur du ställer in din dator med Windows NT/2000/XP så att den hämtar en IP-adress automatiskt. Detta säkerställer att din dator kan kommunicera med P-334WH. Se bruksanvisningen för detaljerad IP-adresskonfiguration för andra Windows och Macintosh operativsystem. 1 I Windows XP, klicka på...
Page 111
PPTP 連接 A 選擇 PPTP 為廣域網路連線類型。 B 輸入一個 使用者名稱及密碼 C 如果您的 ISP 不配置固定的 PPTP IP 位址,選擇 自動由 ISP 取得 。 選擇 使用固定 IP 位址以給予 P-334WH 一個固定的、唯一的 PPTP IP 位址及子網路遮罩。 D 輸入一個 PPTP 伺服器 IP 位址 E 輸入一個 連線識別碼 / 名稱 ( 如果有提供 ) F 如果您的...
Page 113
網際網路接取設定完成 如果您有任何網際網路接取問題,請遵循畫面上的指 示。 按一下 完成,完成精靈設定。 疑難排解 1 如果無法在 Windows XP 或 Windows Server 2003 中使用 Internet Explorer 存取網頁設定介面,請確認 您允許彈出式視窗出現、JavaScripts 與 Java 權限或在 Internet Explorer 設定比 High ( 高 ) 低的安全層 級 ( 在 Internet Explorer 中,按一下工具 > 網際網路選項 > 安全性 > 自訂層級 ...)。請參閱 《使用手冊》 的附錄,取得詳細資訊。...
Page 114
3 在區域連線上按一下滑鼠右鍵,然後按內容。 4 選取 Internet Protocol (TCP/IP) ( 在 Win XP 中位於一 般索引標籤上 ),然後按一下內容。 5 Internet Protocol TCP/IP 內容畫面會開啟 ( 在 Win XP 中位於一般索引標籤上 )。 6 選取自動取得 IP 位址和自動取得 DNS 伺服器位址選 項。 7 按一下確定,關閉 Internet Protocol (TCP/IP) 內容視 窗。 8 按一下關閉 ( 在 Windows 2000/NT 中為確定 ),關閉區 域連線內容視窗。...