Advertisement
9.3.
STORAGE
NOTE: Prior to storage, the following steps should be taken:
9.3.1.
Remove the shampoo head and use the end of the extension
tube to suck up any remaining liquid. Run the vacuum
cleaner until the tubes and hose are clean and dry.
9.3.2.
Switch off the unit and unplug from the power supply. Then
empty the main tank and shampoo tank.
9.3.3. Gently remove the foam filter to dry. Refit for further wet
suction. For dry vacuuming you must fit a dry cartridge filter.
10. MAINTENANCE
10.1.
GENERAL MAINTENANCE
WARNING! Ensure the machine is unplugged from the power supply.
‰
10.1.1. Disconnect the hose from the container (fig.7.2).
10.1.2. Undo the clasps and remove motor head from the container (fig.7.3).
10.1.3. Clear out any dirt or debris from the container and hose (fig.7.4).
10.1.4. Clean the foam filter by washing it in a mild soapy solution (fig.7.5).
10.1.5. Check that the telescopic suction tube operates smoothly, and check
the power cable to make sure it has not received any damage.
10.1.6. Check the O Ring (fig.8) on the mail hose connector (Item 33) for wear.
10.1.7. Replace O rings if necessary (Item 32).
10.2.
CARTRIDGE FILTER MAINTENANCE See also Section 6
10.2.1. Handle the filter carefully when cleaning or installing.
10.2.2. Carefully remove the cartridge filter (fig.9A) and inspect it for damage.
A filter that has small holes or tears in it will not perform efficiently
and should be replaced.
10.2.3. To clean a dry filter, tap it inside a waste bin (fig.9B).
DO NOT use a wet cartridge filter for dry vacuuming as
8
the filter will clog quickly. To clean a wet cartridge filter it
should be rinsed from the inside (fig.9B) and allowed to air
dry for 24 hours.
10.3.
To fit a new/cleaned filter, slide it over the filter basket (fig.9C)
and push it home fully (fig.9D).
10.4.
Check and clean, if necessary, the exhaust filter (Item 3), found at the rear of the motor head, before each use. Open the
exhaust outlet cover (Item 2) and remove the exhaust filter, clean with a brush or blow with air, replace before switching machine on.
11. TROUBLESHOOTING
Problem
Cleaner will not operate.
Dust comes from the motor cover.
Reduced efficiency and increased
Motor speed/vibration.
No solution spraying out.
Leak from drum connector.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
Reason
No power supply.
Faulty power cable, switch or motor.
Container full of liquid.
Filter missing or damaged.
Filter clogged.
Nozzle, hose or container inlet blocked.
Switch in wrong position.
Shampoo tank is empty.
Incorrectly fitted trigger or pipes.
O ring on male connector damaged.
01284 703534
sales@sealey.co.uk
Original Language Version
Solution
Check supply.
Check and repair or replace faulty item.
Empty container.
Fit or replace appropriate filter.
Clean or replace appropriate filter.
Check nozzle, hose and container inlet for
blockage.
Turn switch to the required position.
Add more shampoo.
Check fittings and connections.
Ensure there are no kinks in tubes.
Replace O ring.
www.sealey.co.uk
PC310 | Issue 8 (H,F,1...) 08/08/2019
fig.7
fig.8
fig.9
Advertisement
