Table of Contents
Advertisement
Battery Charger User Guide
MODEL: CN-4000
AC Input: 220-240VAC, 50-60Hz, 0.8A
DC Output: 12VDC, 4A;
6VDC, 4A;
Temperature Controlled
Please read and understand all important safety and operating instructions before using this
charger. In addition, please read and follow all battery and vehicle manufacturer's
instructions and cautionary markings.
Advertisement
Table of Contents
Related Manuals for Shark CN-4000
Summary of Contents for Shark CN-4000
- Page 1 Battery Charger User Guide MODEL: CN-4000 AC Input: 220-240VAC, 50-60Hz, 0.8A DC Output: 12VDC, 4A; 6VDC, 4A; Temperature Controlled Please read and understand all important safety and operating instructions before using this charger. In addition, please read and follow all battery and vehicle manufacturer’s...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS SAFETY PRECAUTIONS FOR WORKING IN THE VICINITY OF A BATTERY 1) Batteries generate explosive gases during normal operation. Use in well-ventilated area. 2) Consider having someone close enough or within the range of your voice to come to your aid when you work near a battery. -
Page 3: Connecting To The Battery
4) Connect and disconnect DC output only after setting AC cord from electric outlet. 5) Use of an attachment not recommended or sold by the manufacturer may result in a risk of fire, electric shock or injury to persons. 6) Do not overcharge batteries by selecting the wrong charge mode. 7) To reduce the risk of damage to electric plug and cord, pull by the plug rather than the cord when disconnecting charger. - Page 4 ABOUT CN-4000 1) The CN-4000 is designed for charging all types of 6V lead-acid and 12V lead-acid batteries, including WET (Flooded), MF (Maintenance-Free), EFB (Enhanced Flooded Battery), GEL, AGM (Absorbed Glass Mat) batteries. It is suitable for charging battery capacities from 1.2 to 130 Amp-Hours and maintaining all battery sizes.
-
Page 5: Charging Modes
CHARGING MODES CN-4000 has ten modes (sel): Standby, 12V STD, 12V COLD, 12V AGM, 12V AGM+COLD, 6V STD, 12V STD Repair, 12V COLD Repair, 12V AGM Repair and 12V AGM+COLD Repair. Do not operate the charger until you confirm the appropriate charge mode for your battery. - Page 6 Icon Battery Mode Explanation Display Size (Ah) Not charging or providing any power Standby ------ ------ (LCD screen turns black and Green LED is on) Charging 12V WET/GEL/MF/EFB Keep on 1.2-130 batteries Charging 12V WET/GEL/MF/EFB Keep on 1.2-130 batteries below 10 (50 ) Keep on 1.2-130 Charging 12V AGM batteries...
-
Page 7: Charging Steps
Repairing 12V AGM batteries below Flash 1.2-130 10 (50 ) Using 12V REPAIR This mode is for LEAD-ACID batteries only. It is an advanced battery recovery mode for repairing old, idle, stratified or sulfated batteries. NOT all batteries can be recovered. For optimal results, take the battery through a full charge cycle, bringing the battery to full charge, before using this mode. -
Page 8: Battery Level Indicator
to the threshold) STEP 6: ABSORPTION (Provide gradually declining current charge for maximum battery voltage) STEP 7: ANALYSE (Test if the battery can hold charge) STEP 8: MAINTENANCE (Continuously monitor the battery, and charging current will intelligently adapt to the variable battery voltage). BATTERY LEVEL INDICATOR Display Explanation... -
Page 9: Charging Time
CHARGING TIME Different battery capacity and residual voltage would affect the charging time. Following data is only for reference (when discharge 12V lead-acid battery to 9V, with 5A discharge current. Battery Size/Ah Approx. Time to Charge in Hours (12V) 5H @ 14.4V 7H @ 14.7V 8H @ 14.6V 11H @ 14.9V...