Fluke 110 Calibration Information Manual
  1. Manuals
  2. Brands
  3. Fluke Manuals
  4. Multimeter
  5. 110
  6. Calibration information manual

Fluke 110 Calibration Information Manual

True-rms multimeter
Hide thumbs Also See for 110:
Table of Contents

Advertisement

Quick Links

110/113/114/115/116/117
True-rms Multimeter
Calibration Information
September 2006 Rev. 2, 5/20
©2006-2020 Fluke Corporation. All rights reserved.
All product names are trademarks of their respective companies.
Specifications are subject to change without notice.

Advertisement

Table of Contents
loading

Related Manuals for Fluke 110

Summary of Contents for Fluke 110

  • Page 1 110/113/114/115/116/117 True-rms Multimeter Calibration Information September 2006 Rev. 2, 5/20 ©2006-2020 Fluke Corporation. All rights reserved. All product names are trademarks of their respective companies. Specifications are subject to change without notice.
  • Page 2 Parts, product repairs, and services are warranted for 90 days. This warranty extends only to the original buyer or end-user customer of a Fluke authorized reseller, and does not apply to fuses, disposable batteries, or to any product which, in Fluke's opinion, has been misused, altered, neglected, contaminated, or damaged by accident or abnormal conditions of operation or handling.

  • Page 3: Table Of Contents

    Table of Contents Title Page Introduction ......................How to Contact Fluke.................... Safety Information....................Specifications......................Maintenance ......................Fuse Test (115, 117) ..................Battery and Fuse Replacement ............... Cleaning......................Features........................ Performance Tests....................Required Equipment ..................Display Test ..................... 110/114/115/116/117 .................. 113 ......................
  • Page 4 110/113/114/115/116/117 Calibration Information...

  • Page 5: Introduction

    This Calibration Information provides the information necessary to adjust and verify the performance of the Fluke Models 110, 113, 114, 115, 115C, 116, 116C, 117, and 117C True RMS Multimeter (the Meter or Product). When specific models are noted in this manual, the “C” version is also included. For example, when the listed model is 115, the instructions are applicable to the 115C as well.

  • Page 6: Maintenance

    If the display shows a resistance value in the range of that shown in Figure 1, the fuse is good. If the display reads 0L, replace the fuse and test again. If the display shows any other value, have the Meter serviced. See How to Contact Fluke earlier in this document.

  • Page 7: Battery And Fuse Replacement

    True-rms Multimeter Maintenance Battery and Fuse Replacement XW Warning To prevent shock, injury, or damage to the Meter: • Remove test leads from the Meter before opening the case or battery door. • Use ONLY a fuse with the amperage, interrupt voltage, and speed ratings specified. h Static Awareness h Semiconductors and integrated circuits can be damaged by electrostatic discharge during handling.

  • Page 8: Cleaning

    5. Remove the fuse from its holder and replace it with an 11 A, 1000 V, FAST fuse having a minimum interrupt rating of 17 000 A. Use only Fluke PN 803293. 6. To re-assemble the Meter, first attach the case bottom to the case top, then install the two screws. Finally, insert the Meter into its holster.

  • Page 9: Features

    True-rms Multimeter Features Features Table 1 is a list of the features for each Meter. Table 1. Features Switch Measurement Function Position The Meter is turned off.       Automatically selects ac or dc volts based on the sensed ...

  • Page 10: Performance Tests

    0 to 30 M Capacitance 9 to 900 μF Temperature 0 °C to 400 °C Frequency 2 V, 50 kHz Fluke 80 AK Temperature K-type Thermocouple Adapter Accessory K-type Thermocouple, mini-plug on both ends Temperature Double Banana plug VoltAlert [1] For accuracy specifications, see the Users Manual for the product.

  • Page 11: Display Test

    True-rms Multimeter Performance Tests Display Test 110/114/115/116/117 Push K and turn the rotary switch to the e position. Compare the display with the example in Figure 3. Check all segments for clarity and contrast. Push K and turn the rotary switch to the k CHEK position. Compare the display with the example in Figure 3.

  • Page 12: Preparing For The Performance Tests

    To verify the accuracy of the DMM functions, do the following: 1. Connect the Calibrator to the VΩ and COM input terminals on the Meter. 2. Turn the rotary switch to the function listed in each step of Table 3 (110, 114, 115, 116, 117) or Table 4 (113).
  • Page 13 True-rms Multimeter Performance Tests Table 3. DMM Performance Tests: 110/114/115/116/117 (cont.) Display Reading Step Function Range Applied Ω Ω Beeper On Continuity Ω Ω Beeper Off 6.000 V 5 V, 45 Hz 4.947 to 5.053 6.000 V 5 V, 1 Hz 4.897 to 5.103...
  • Page 14 VoltAlert [1] If using a Fluke 9100 calibrator, the Calibrator Frequency mode must be used to obtain accurate frequency. [2] To keep from tripping the calibrator to standby, ramp up the voltage in 50 V increments with a 5 second delay between increments.
  • Page 15 True-rms Multimeter Performance Tests Table 4. DMM Performance Tests: 113 Step Function Range Applied Display Reading 0.0 Ω 600.0 0.0 to 0.2 (2-Wire comp) 500 Ω 600.0 495.3 to 504.7 Ohms 6.000 k 5 kΩ 4.954 to 5.046 60.00 k 50 kΩ...

  • Page 16: Testing The Voltalert Function (117 Only)

    Verify that the beeper is silent and the red LED is off. 2. Connect a double banana plug to the output voltage terminals of the calibrator (Fluke 5500A or equivalent). 3. Set the calibrator output to 10 V at 60 Hz.
  • Page 17 True-rms Multimeter Performance Tests For Fluke 117 with S/N 38920290 through 42913406, use this alternate calibration procedure to verify that VoltAlert functions properly. See Figure 5. 1. Select the VoltAlert function: a. Verify that Hi is on the display. b. Verify that the beeper is silent and the red LED is off.

  • Page 18: Calibration Adjustment

    The password can be changed or reset to the default as described in following paragraphs. Changing the Password Use these steps to change the Meter password: 1. 110/114/115/116/117: While pressing K, turn the rotary switch from OFF to Ω function. 113: While pressing q, turn the rotary switch from OFF to Ω...

  • Page 19: Restoring The Default Password

    True-rms Multimeter Calibration Adjustment Restoring the Default Password If the calibration password is forgotten, the default password (1234) can be manually restored: XW Warning To prevent electric shock or personal injury, remove the test leads and any input signal before removing the Meter’s back case.

  • Page 20: Meter Buttons Used In The Calibration Steps

    If you turn off the Meter before completion of the adjustment procedure, the calibration constants do not change. To adjust the Meter calibration: 1. 110/114/115/116/117: While pressing K, turn the rotary switch from OFF to Ω function. 113: While pressing q, turn the rotary switch from OFF to Ω function.
  • Page 21 Set the calibrator to Standby before you change the function switch position and after you complete adjustment of each function. If the calibration adjustment procedure is not properly completed, the Meter will not operate correctly. Table 5. Calibration Adjustment Steps (110/114/115/116/117) Rotary Display Reading Input...
  • Page 22 110/113/114/115/116/117 Calibration Information Table 5. Calibration Adjustment Steps (110/114/115/116/117) (cont.) Rotary Display Reading Input Calibrator Switch Terminals Source Value 110/114 [1, 2] Position Set calibrator to standby, reconfigure leads, and program for amps output. A and COM 6 A, 60 Hz...

  • Page 23: Replacement Parts

     LCD,FLUKE-11X,3.2V,TN,4-DIGIT,1/4-DUTY,1/3-BIAS,LEPTON 2509955 CONNECTOR,ELASTOMERIC,.010 IN CTR,.218 IN HIGH,.090 IN  2534229 THK,2.284 IN LONG,BULK FLUKE-117-2006,BRACKET MASK, 117 2525608 FLUKE-117-2006-06,BRACKET MASK, 117 China 2631059 FLUKE-117-2006-08,BRACKET MASK, 113 3088082 FLUKE-117-2006-01,BRACKET MASK, 114 2527431  FLUKE-117-2006-02,BRACKET MASK, 115 2527446 FLUKE-117-2006-04,BRACKET MASK, 115 China...
  • Page 24 Description Part Number FLUKE-117-2002,CASE BOTTOM 2525566  FLUKE-117-2002,CASE BOTTOM, 11X China 2631098 FLUKE-117-2003,BATTERY DOOR,TILT STAND 2720600  FLUKE-117-2003,BATTERY DOOR, TILT STAND, 11X China 2720617 SCREW,2-28,.250,PAN,PHILLIPS,STEEL,ZINCCHROMATE,  2516493 PLASTITE 48 THREAD FORMING SCREW,M3,4MM,PAN,PHILLIPS,STEEL,ZINC-CHROMATE 2 (114, 110, 116)  2032811 3 (115,117) SCREW,5-14,.750,PAN,PHILLIPS,STEEL,BLACK CHROMATE,...
  • Page 25 True-rms Multimeter Replacement Parts Figure 7. Exploded View of Meter 15 4 PL 2 PL...
  • Page 26 110/113/114/115/116/117 Calibration Information...

This manual is also suitable for:

113114115116117

Table of Contents