Table of Contents
Advertisement
STANDBY
STANDBY
/ON
TIMER
PRESET/TUNING/BAND
A/B/C/D/E
INPUT
/
BASS
TREBLE
REC/
AUTO/
PHONES
MODE
DOLBY NR
PAUSE
MANUAL
TIMER
DIRECTION
1
POWER
1
2
1
2
4
5
4
5
7
8
7
8
0
TUNER
PRESET
PRESET
TIME
PROG
R.TIME
TIME
A
B
EDIT
DISC SKIP
MODE
9
D
VCD/CD
RETURN
/
SELECT
KARAOKE
INTRO
DIGEST
TIME INDEX
TIME INDEX
DIRECTION
TAPE
REC/ PAUSE
CENTER/
—
LEVEL
REAR/ DELAY
KEY/ECHO
PROGRAM
MUSIC
SLEEP
VOLUME
Display information during programming
Next play order
TRACK
NR
CD
Selected track
Total remaining time on
this side of the tape
number
TRACK
REM
NR
CD
Programmed track numbers light up and
only programmable track numbers
among unprogrammed ones flash.
PROGRAM
B.BOOST
MUSIC
VOLUME
UP
DOWN
MEMORY
RANDOM
REPEAT
TIME
DISPLAY
TIME ADJ
HOUR
MIN
TIME
5
3
3
6
6
9
+ I0
7
C
3
E
4
TEST
INPUT
1
Selected disc
1 2 3 4
5
6
7 8 9 10
11
12
A
V
PROG
13 14 15
OVER 15
Side of the tape
1 2 3 4
5
6
7 8 9 10
11
12
A
PROG
V
13 14 15
OVER 15
Manual EDIT recording
You can program tracks manually while watching the remaining
time on both sides of the tape.
1
Press INPUT
or
repeatedly until "VCD/CD" (1) appears
on the display, and load a disc (or discs) on the disc tray.
2
Follow steps 3–5 on page 30.
3
Press PROG.
* "PROG" and "P-01" will light up on the display, and all track
numbers on the selected disc will begin blinking.
4
If necessary, select the desired disc by pressing DISC SKIP.
5
Select the desired track number by pressing the numeric buttons.
6
Repeat steps 4 and 5 to program more selections for side A of
the tape. You can select the same track again.
* Pressing TIME displays the total remaining time on side A of
the tape for about 1 second, and then it is replaced by the
display of the next play order.
* You can only select track numbers 1 through 15 for manual
EDIT recording. All track numbers higher than 15 i.e.16, 17,
18... cannot be selected for recording even if there is
recordable space available on the tape.
"TM OVER" will appear on the display.
At this time, however, if any other track number is flashing
continuously on the display, you can program it instead of the
unprogrammable one.
7
When the programming for side A is finished, press R. TIME.
* "Side–B" appears on the display. You can begin programming
for side B.
* After following this step, you can check the programmed
contents for side A and side B alternately by pressing R.
TIME at any time before you press EDIT in step 9.
* The tape side indicator (9) shows the programming side
currently selected.
8
Repeat steps 4 and 5 to program selections for side B of the tape.
You can select the same track again.
9
Press EDIT. ("EDIT" (8) lights up on the display.)
The recording begins.
Note
To check, cancel or correct program data, refer to page 16.
To cancel the EDIT function
Before recording, press
tape deck.
To stop recording
Press
on the tape deck.
(At this time, disc play automatically stops.)
Notes on recording with the EDIT function
• The maximum number of tracks that can be programmed is 20.
• The track number 16 or higher cannot be programmed by this function.
• The CD/Video CD player's repeat play mode will be canceled during
this recording mode.
Recording
on the CD/Video CD player or the
-31
E
Advertisement
Table of Contents
