To Perform Transmit High Power Tuning, Do The Following; To Perform Transmit Low Power Tuning, Do The Following; Table 5-3. Transmit High/Low Power Level - Motorola Commercial Series Basic Service Manual

Radio Alignment Procedures: Transmitter Alignment Options
RF Band (MHz)
VHF 136-162 MHz
VHF 136-162 MHz
VHF 146-174 MHz
VHF 146-174 MHz
UHF 1 403-440 MHz
UHF 1 403-440 MHz
UHF 2 438-470 MHz
UHF 2 438-470 MHz
UHF 3 465-495 MHz
UHF 3 465-495 MHz

5.4.3.1 To Perform Transmit High Power Tuning, do the following:

1. Under the Tx Align menu, select Transmit Power, then select High
2. Press PTT Toggle. This will key the radio up at 1st test frequency (F1).
3. Adjust the high power level to be as defined by
values in the edit control (press ENTER to confirm your selection after typing in the softpot value).
4. Press PTT Toggle to dekey the radio, go to the next frequency point by selecting the slider, typing
in the edit control box (press ENTER to confirm selection after typing in the softpot value) or
toggling the softpot value using the spin control.
5. Press PTT Toggle again to key up the radio at the selected frequency point.
6. Repeat steps 3-5 for the remaining test frequencies (F2-7)
7. Press Program to store the softpot values into the radio's codeplug.
8. Exit the Transmit High Power function.
9. If the radio uses only high power channels, proceed to adjust modulation. If low power channels
are used, perform Transmit Low Power Tuning as defined.

5.4.3.2 To Perform Transmit Low Power Tuning, do the following: -

1. Under the Tx Align menu, select Transmit Power, and then select Low.
2. Press PTT Toggle. This will key the radio up at 1st test frequency (F1).
3. Adjust the power level to be as defined by country power level specifications by moving the
slider/spin control or keying in values in the edit control (press ENTER to confirm your selection
after typing in the softpot value).
4. Press PTT Toggle to dekey the radio, go to the next frequency point by selecting the slider, typing
in the edit control box (press ENTER to confirm your selection) or toggling the softpot value using
the spin control.
5. Press PTT Toggle again to key up the radio at the selected frequency point.
6. Repeat steps 3-5 for the remaining test frequencies (F2-F7).
7. Press Program to store the softpot values into the radio's codeplug.
68009328001-A

Table 5-3. Transmit High/Low Power Level

Model Number
AAH50JDF9AA5AN
AAH50JDH9AA6AN
AAH50KDF9AA5AN
AAH50KDH9AA6AN
AAH50QDF9AA5AN
AAH50QDH9AA6AN
AAH50RDF9AA5AN
AAH50RDH9AA6AN
AAH50SDF9AA5AN
AAH50SDH9AA6AN
High Power(W)
5.2-5.5 1.1-1.3
5.2-5.5 1.1-1.3
5.2-5.5 1.1-1.3
5.2-5.5 1.1-1.3
4.2-4.5 1.1-1.3
4.2-4.5 1.1-1.3
4.2-4.5 1.1-1.3
4.2-4.5 1.1-1.3
4.2-4.5 1.1-1.3
4.2-4.5 1.1-1.3
(Figure
Table 5-3. Move the slider/spin control or keying in
5-7
Low Power (W)
5-5).
December, 2009