Layer Edit 1 - Yamaha CS1X Owner's Manual

# LCD
0 off
1 PerfLevel (Performance Level) (page 23)
2 ArpgTempo (Arpeggiator Tempo) (page 23)
3 ArpgType (Arpeggiator Type) (page 23)
4 ArpgSubdiv (Arpeggiator Subdivide) (page 23)
5 MWCutoff (MW Cutoff) (page 25)
6 MWPModDpth (MW Pitch Modulation Depth) (page 25)
7 MWFModDpth (MW Filter Modulation Depth) (page 25)
8 PBRange (Pitch Bend Range) (page 25)
9 FCCutoff (FC Cutoff) (page 26)
10 FCFModDpth (FC Filter Modulation Depth) (page 26)
11 FCVariDpth (FC Variation Depth) (page 26)
12 PortaTime (Portamento Time) (page 26)
13 *FEGDcyTime (FEG Decay Time) (page 32)
14 *AEGDcyTime (AEG Decay Time) (page 30)
15 *ChoToRev (Chorus Send To Reverb)
16 *VariCntrl (Variation Control)
17 *RevChoSend (Reverb And Chorus Send)
18 *ChorusSend (Chorus Send) (page 38)
19 *ReverbSend (Reverb Send) (page 38)
20 *Pan (page 38)
21 *LFOSpeed (LFO Speed) (page 31)
22 *LFOPMod (Vibrato Depth) (page 30)
23 *VibDelay (Vibrato Delay)
24 *LFOAMod (LFO Amplitude Modulation Depth) (page 30)
25 *LFOFMod (LFO Filter Modulation Depth) (page 31)
26 *FEGAtkTime (FEG Attack Time) (page 32)
27 *FEGSusLvl (FEG Sustain Level) (page 32)
28 *FEGVelSens (FEG Level Velocity Sensitivity)
29 *Pitch (Oscillator Pitch)
Parameters with an asterisk affect entire Layers in a Performance. You
cannot directly edit them from the LCD, but you can assign them to the
ASSIGN 1 knob.
You can also select each parameter by inputting the corresponding
number using the numeric keypad.
Layer Edit 1 (independently applied to each Layer)
The functions in this row provide various parameters mainly
related to the keyboard such as Tune, Note Limit and Velocity.
The parameters can be set for each Layer in a Performance.
TUNE
NOTE DETUNE LIMIT
SFT LOW
AEG
ATK DCY DCY
TIME TIME LEVEL
FEG
ATK DCY DCY
TIME TIME LEVEL
BANK PROGRAM VOLUME
DEMO
PERFORMANCE MULTI
STORE UTILITY
NOTE VEL ASSIGN2
LIMIT LIMIT LIMIT OFFSET DEPTH PARAM DATA
HIGH LOW HIGH
LFO
REL AMOD PMOD FMOD WAVE SPEED PHASE
TIME INIT
PEG
REL INIT ATK ATK DCY REL REL
TIME LEVEL TIME LEVEL TIME TIME LEVEL
EFFECT FILTER POLY/
PAN REV CHO VARI CUTOFF REZ MONO
SEND SEND SEND
TUNE
This sets the tuning of a Layer. There are two parameters, NOTE
SFT (Note Shift) and DETUNE.
Note Shift
NOTE SFT (Note Shift): Raises or lowers the pitch of the voice in
semitones.
Settings:
-24 ~ +24 (semitones)
DETUNE: Raises or lowers the pitch of the voice in fine
increments or decrements (0.1 Hz each).
Settings:
-12.8 Hz ~ +12.7 Hz
NOTE
This sets the range of notes that each Layer will play. There are
two parameters, LIMIT LOW and LIMIT HIGH.
Limit Low
LIMIT LOW: Determines the low note limit, or the lowest note
that will be played by the voice.
LAYER
LIMIT HIGH: Determines the high note limit, or the highest note
that will be played by the voice.
C-2 • • • C1
0 • • • 36 Note Name
Note Number
Settings:
LIMIT LOW: C-2 ~ G8
LIMIT HIGH: C-2 ~ G8
NOTE
HIGH note, or the LIMIT HIGH note below the LIMIT LOW note.
27
Detune
Limit High
C2 C3 C4
48 60 72
LIMIT LOW is set to C2 and LIMIT HIGH is
set to C4. Range of notes that can be played.
CS1x Keyboard
It is not possible to set the LIMIT LOW note above the LIMIT
C5 C6 • • • G8
• • • 127
84 96