IBM eServer xSeries Configuration And Options Manual page 42

Part
Number
09N4042 10/20 GB NS Internal SCSI Tape Drive
00N7991 20/40 GB DDS/4 4-mm Internal Tape Drive
09N4040 20/40 GB DLT Internal SCSI Tape Drive
00N7990 40/80 GB DLT Internal SCSI Tape Drive
00N8017 60/120GB 8-mm M2 SCSI Tape Drive
Tape Autoloaders
10
00N79xx DLT Tape Autoloader
00N7992 120/240GB DDS/4 Tape Autoloader
External Tape Libraries
11
00N79xx DLT Tape Library
External Tape Enclosures
10L7440 External Half High SCSI Storage Enclosure
03K8705 DLT External SCSI Enclosure
03K8756 NetMEDIA Storage Expansion Unit EL
10L7113 NetMEDIA Systems Management Adapter
Associated Options
68-pin External Multimode LVD/SE SCSI
00N7956
Terminator
10K2340 Media BayTray and LVD Cable Kit
Note: Netfinity 5600 includes a wide two-drop single-ended terminated cable which can be used for attachment of internal tape drives to the onboard Ultra2 controller when the hot-swap backplane is attached
to a RAID controller. If LVD support is required, an optional LVD cable must be ordered. An external Ultra2 SCSI port is available with a 0.8-mm VHDCI connector. External tape enclosures are supported
by the standard external SCSI port or PCI Wide Ultra160 SCSI Adapter (P/N 19K4646) which has an external 0.8-mm VHDCI connector.
1. Non-RAID Configurations: Requires PCI Wide Ultra160 SCSI Adapter (P/N 19K4646) which contains a five-drop multi-mode terminated LVD SCSI cable.
2. RAID configurations: Configurations where the hot-swap backplane is cabled to a RAID controller, require the two-drop multi-mode terminated LVD SCSI cable included with Media Bay Tray and LVD
Cable Kit (P/N 10K2340) for support of LVD devices in LVD mode. Use of the included single-ended terminated cable with an LVD device will be limited to single-ended SCSI rules.
3. LVD support for LVD devices installed in a NetMEDIA Storage Expansion Unit EL (P/N 03K8756) requires replacement of the standard single-ended internal cables with one or more (depending on
configuration) cables from Media Bay Tray and LVD Cable Kit (P/N 10K2340) which contains a single two-drop mult-mode LVD-SCSI terminated cable. If the standard cables are used for attachment to LVD
devices, single-ended SCSI rules and bus speeds apply.
4. Requires 68-pin External Multimode LVD/SE SCSI terminator (P/N 00N7956).
5. Tape library attributes and prerequisites are located in Appendix B: Tape Library Attributes.
6. Provides a black desktop 133 mm (5.25") half-high (HH) tape enclosure. Connector is configurable as 50-pin Centronix or 68-pin high density. Requires either tape drive self termination
or 68-pin External Multimode LVD/SE SCSI Terminator (P/N 00N7956).
7. Provides a black desktop DLT tape enclosure with a 68-pin high density external connector. Requires termination by the tape drive or by installation of an External Multimode LVD/SE SCSI terminator (P/
N 00N7956).
8. NetMEDIA Storage Expansion Unit EL (P/N 03K8756) is a black 3U, 19" rack-mountable tape enclosure which includes two full high (FH) or four half high (HH) extended length 133 mm (5.25") bays,
two external 68-pin high density connectors and two internal four-drop single-ended terminated 16-bit SCSI cables for device attachment. Two power supplies and two power cords are also included. Tip: The
front rail clips will need to be reversed and screwed in from behind to secure the unit in a Rack Cabinet P/N 930842X.
9. NetMEDIA Systems Management Adapter (P/N 10L7113) may be installed in a NetMEDIA Storage Expansion Unit to provide repeater function, LVDS interface, aggregate cable lengths up to 12 meters
when attached to an LVD SCSI controller, and auto-termination when the Expansion Unit is powered off. External connector is 0.8-mm VHDCI.
10. Where 'xx' represents a country specific power cord code: 70=UK, 71=Swiss, 72=Italy, 73=Israel, 33L4981=EU1, 33L4982=Denmark, 33L4983=South Africa/India.
11. Where 'xx' represents a country specific power cord code:
82=Denmark, 83=India/South Africa, 84=UK, 85=Swiss, 86=Italy, 87=Israel.
Note: Additional tape details can be found in Appendix A: Tape Drive Attributes.
Note: For a complete list of all IBM and non-IBM options compatibility with Network Operating Systems and IBM xSeries and Netfinity Servers,
41
Updated
28/02/01
xSeries 240 / Netfinity 5600 Tape Options
Tape Drives Bays
Supported
1
A, B
2
A, B
1
A+B
2
A+B
2
A, B
N/A
2
A+B
5
6
7
8
9
2,3
Tower versions
- 74=EU1, 75=Denmark, 76=India/South Africa, 77=UK, 78=Swiss, 79=Italy, 80=Israel:
access the IBM ServerProven compatibility pages on the Web at URL http://www.ibm.com/pc/us/compat
SCSI Form
Interface Factor
(bit)
89 mm
(3.5") SL or
8
133 mm
(5.25") HH
89 mm
(3.5") HH
16 Ultra2 LVD
or 133 mm
(5.25") HH
133 mm
8
(5.25") FH
133 mm
16 Ultra2 LVD
(5.25") FH
133 mm
16 Ultra2 LVD
(5.25") HH
16 Desktop
133 mm
16 Ultra2 LVD (5.25") FH
Desktop
- 16
orRack
- 8/16 Desktop
16 Desktop
- 16 Rack
- 16 LVD -
- 16 LVD/SE Ext.
- 16 LVD Int.
Termination 68/50-pin
Included Converter Incl.
Y Y
N N/A
N Y
N N/A
N N/A
Y -
N N/A
Y -
N N
N N
Y N
N N
Y N
Y N
Rack versions
Ext. Tape
Enclosures
10L7440
4
10L7440 ,
3
03K8756
4
03K8705 ,
03K8756
4
03K8705 ,
3
03K8756
4
10L7440 ,
3
03K8756
-
3
03K8756
-
-
-
-
03K8756
10L7440,
03K8705
03K8756
- 81=EU1,