Dometic 300 Series Instruction Manual

Notes on using the manual
Caution!
Safety Instruction: Failure to observe this instruction can cause material damage and impair
the function of the device.
Note
Supplementary information for operating the device.
fig. A : This refers to an element in an illustration. In this example, item A in figure 1.
1
General safety instructions
The manufacturer will not be held liable for claims for damage resulting from the following:
• Faulty installation or connection
• Damage to the unit from mechanical influences, misuse or abuse
• Alterations to the unit without express written permission from the manufacturer
• Use for purposes other than those described in this manual
Warnings
The following statements must be read and understood before installing, servicing and/or
operating this product. Modification of this product may result in property damage.
1. Do not use chlorine or caustic chemicals, such as laundry bleach or drain-opening types, in
the system. These products damage the seals in toilets and other plumbing valves.
2. Do not permit foreign objects (paper towels, paper cups, diapers, sanitary napkins, etc.) to be
flushed through the toilet.
3. Mechanical seal toilets are designed to only discharge directly into a holding tank. Horizontal
pipe runs as found in conventional residential or commercial plumbing systems cannot be
accommodated.
4. Toilet bowl must be regularly cleaned and winterized according to "Cleaning" and "Winteriza-
tion and storage" procedures in this manual, or your warranty coverage may be voided.
Intended use
Dometic 300, 310 and 320 series toilets provide lightweight, residential-size toilets for installation
directly above a holding tank.
Benefits
PowerFlush technology. Improved pressurized rim flow creates high-speed vortex of water for full
bowl rinsing.
Premium user comfort. Full-size seat and deep bowl result in greater homelike performance.
Easy installation. Two-bolt design fits most existing toilet floor flanges – great for new or replace-
ment installations. Just place on floor flange, tighten bolts, connect water, and it's ready.
Ergonomically enhanced pedal operation. Lower pedal height for easier use; "one-direction"
action to add water and flush.
IF SERVICE OF THIS TOILET IS EVER REQUIRED,
READ THIS BEFORE SERVICING PRODUCT.
STOP
DO NOT REMOVE TOILET FROM VEHICLE.
DO NOT SEPARATE CERAMIC BOWL FROM PLASTIC BASE.
DO NOT REMOVE FOOT PEDAL FROM BASE.
DISASSEMBLY OF COMPONENTS MAY VOID WARRANTY.
SEE MANUAL AND REPLACEMENT KITS FOR SERVICE INFORMATION.
Dometic Corporation
Sanitation Division
Call Customer Service: 1-800-321-9886 (8 a.m. – 5 p.m. ET)
TOILET DOES NOT NEED TO BE REMOVED FROM VEHICLE FOR BASIC REPAIRS (if necessary)
Flush ball seal – Dometic's Snap-in water valve cartridge –
revolutionary ball seal allows future Allows easy replacement of worn
replacement of worn or damaged or damaged water valves. In cold
climates, be sure to follow winter-
ball seals without requiring tools or
toilet disassembly. The ball seal can izing procedure in owner's manual
be changed in just a few minutes to help avoid water valve failure.
without removing the toilet from the Refer to replacement instructions
floor. Detailed replacement instruc- in new water valve kit prior to
tions are included with replacement removal or installation of water
ball seal kits. valve assembly.
Each Dometic toilet is 100% factory-tested to assure a watertight seal in the toilet bowl before it
is shipped.
After installation at the RV or other vehicle factory, the entire toilet and waste tank system is flood-
tested for leaks by filling the system with water to the rim of the toilet bowl. This process requires
holding the flush ball open with a device which may temporarily distort the ball seal from its original
shape and, as a result, cause the seal to leak water into the waste tank during normal use. The ball seal
may need to be reconditioned to its original shape.
IF NEW TOILET DOES NOT HOLD WATER IN BOWL...
Please follow the procedures below before attempting to replace the seal.
1. Hold flush ball in full open position by pressing on
pedal.
2. Using finger, apply moderate downward pressure
around edge of ball seal.
3. Close flush ball.
4. Keeping flush ball closed, pour one quart of
hot tap water into toilet bowl.
5. Let water cool completely.
6. Check for leak.
If leak still persists, flush ball seal should be
replaced. Follow instructions provided with
replacement seal kit.
Factory-sealed bowl-to-base
assembly – Unlike other Dometic
foot-pedal toilets, the bowl and
base of 300, 310, and 320 series
toilets should not be separated for
any reason.
300 Series, 310 Series, 320 Series Toilets
Gravity-flush toilet
EN
Instruction manual
SANITATION
TOILETS