Hot water heat pump for indoor installation (60 pages)
Summary of Contents for Dimplex M Flex 0609
Page 1
Glen Dimplex Deutschland Dimplex M Flex 0609 M Flex 0916 M Flex 0916M 09CHOIAOF6 16IHOIAOF6 16CHOIAOF6 Installation and Operating Instruction Air-to-water heat pump in integral design Order no.: DOK4x HOIAO FxDEN EN · FD 0001...
Air-to-water heat pump M Flex English Table of contens Safety notes.................................3 1.1 Symbols and markings ................................3 1.2 Intended use..................................... 3 1.3 Legal regulations and directives ............................3 1.4 Energy-efficient use of the heat pump..........................3 Intended use of the heat pump ........................4 2.1 Area of application..................................
Page 4
English Air-to-water heat pump M Flex 15 Information on the use of data........................33 16 Declaration of conformity ..........................34 DOK4x HOIAO FxDEN · FD 0001 www.glendimplex.de...
Air-to-water heat pump M Flex English Safety notes 1.1 Symbols and markings When connecting the heating system, all country-specific reg- ulations must also be adhered to. Particularly important information in these instructions is This unit can be used by children aged 8 and over and by per- marked with CAUTION! and NOTE.
English Air-to-water heat pump M Flex Intended use of the heat pump 2.1 Area of application The air-to-water heat pump is to be used exclusively for heating and domestic hot water. It can be used in new or existing heat- ing systems.
Air-to-water heat pump M Flex English Scope of supply 3.1 Indoor unit Hydraulic systems (including a dual differential pressureless manifold) 50 l buffer tank Actuator for 3-way reversing valve Refrigeration circuit 3-way reversing valve for generating domestic hot water 10) Heat exchanger refrigerant / heating water Regulated auxiliary circulating pump 11) Compressor Switch box with heating controller...
English Air-to-water heat pump M Flex 3.2 Outdoor unit Evaporator Expansion valve Switch box Connection for refrigerant line DOK4x HOIAO FxDEN · FD 0001 www.glendimplex.de...
Air-to-water heat pump M Flex English Transport 4.1 Outdoor unit The casing panels must be dismantled in the order outlined be- low. A pallet should be used to transport the heat pump to its final The right side panel must be removed first. For this, loosen the installation location.
Page 10
English Air-to-water heat pump M Flex After the final positioning at the installation location, remove the transport fastening on the sprung floor of the compressor on both sides. ATTENTION! Before commissioning, the transport fastening must be re- moved. DOK4x HOIAO FxDEN · FD 0001 www.glendimplex.de...
Air-to-water heat pump M Flex English Positioning 5.1 Outdoor unit Ensure that the cold expelled air is not sucked in again. HINWEIS NOTE Among other things, when selecting the installation locations for the indoor and outdoor units, ensure that the required Do not restrict or block the area around the intake or the air length of refrigerant line is as short as possible.
(Tab. C.3) tic hot water cylinder. Both parts must be installed so that maintenance work can be M Flex 0609 3.80 kg R410A 0.39 kg/m³ 9.7 m³ carried out without hindrance. This can be ensured by main- M Flex 0916(M) 4.78 kg R410A...
Air-to-water heat pump M Flex English Assembly / connection 6.1 Assembly of the refrigerant line heating operation (pos. 1 factory default). Fill the heating sys- tem at the fill and drain cock (pos. 2) until system pressure (ap- and electric wire prox.
English Air-to-water heat pump M Flex Frost protection The following points must be observed when filling the system: Untreated filling water and make-up water must be of A method of manual drainage should be provided for heat drinking water quality pumps which are exposed to frost.
Air-to-water heat pump M Flex English 6.5 Temperature sensor connection The following temperature sensors are already installed or must be installed additionally: Outside temperature (R1) is (NTC-2) Return temperature (R2) installed (NTC-10) Demand sensor (R2.2) installed (NTC-10) ...
English Air-to-water heat pump M Flex 6.6 Electrical connection 6.6.1 Electrical diagram (integration example) Symbol legend see cap. 6.6.2 on page 15 Equipment marking see cap. 6.6.3 on page 15 DOK4x HOIAO FxDEN · FD 0001 www.glendimplex.de...
Page 17
Air-to-water heat pump M Flex English 6.6.2 Symbol legend 6.6.3 Equipment markings +A100 Cooling circuit module Connector +A110 Outdoor unit +A200 Hydraulics /WPM Plug connection +A220 Expansion module WPM +A300 Electrical distribution system +A350 Router Compressor / refrigeration circuit +A400 Hydraulic installation (general) +A411 Circuit 1: mixed...
Page 18
English Air-to-water heat pump M Flex 6.6.4 Electrical connection general External sensor The external sensor (-R1) is connected to the adapter All connection cables must be provided on-site. The cable type board via the plug (grey [3]) "U1" in the hydraulic module (cross-section, conductor type, etc.) must be chosen taking switch box (+A200) into account the relevant electrical parameters (e.g.
M Flex 0609 version. During the brazing process, the pipe system must be flushed 6.8.1 Requirements for the pipe length with an inert gas (e.g.
Page 22
English Air-to-water heat pump M Flex Step 3: Evacuation Connect the vacuum pump on the maintenance valve (with Schrader). Run the vacuum pump until the relevant vacuum is reached. An absolute pressure of at least 0.2 mbar must be achieved during evacuation.
Air-to-water heat pump M Flex English Commissioning 7.1 General 7.3 Procedure To ensure that commissioning is performed correctly, it should The heat pump is commissioned via the touch display. See the only be carried out by an after-sales service technician author- “Operation”...
English Air-to-water heat pump M Flex Cleaning / maintenance 8.1 Maintenance It is then important that the system be thoroughly flushed using appropriate neutralising agents to prevent any damage from To protect the paintwork, avoid leaning anything against the being caused by cleaning agent residue remaining in the sys- device or putting objects on the device.
Air-to-water heat pump M Flex English Faults / troubleshooting This heat pump is a quality product and is designed for trouble- ATTENTION! free operation. In the event that a fault should occur, it will be Before opening the device, ensure that all circuits are discon- indicated on the touch display.
English Air-to-water heat pump M Flex 11 Device information 11.1 Device information heat pump Type and order code M Flex 0609 M Flex 0916M M Flex 0916 Design Heat source Seasonal coefficient of performance (COP) average climate 35 °C / 55 °C...
Page 27
Air-to-water heat pump M Flex English Type and order code M Flex 0609 M Flex 0916M M Flex 0916 Electrical connection Supply voltage / fusing / RCD type 1~/N/PE 230 V (50 Hz) / 1~/N/PE 230 V (50 Hz) /...
English Air-to-water heat pump M Flex 12.3 Dimension drawing legend Outdoor unit Connection refrigerant line 12 x1 mm outdoor unit Connection refrigerant line 18 x 1 mm outdoor unit Condensate drain Feedthrough refrigerant lines and electric wires; con- densate hose Optional feedthrough refrigerant line 18 mm Optional feedthrough electric wires 12 mm Optional feedthrough, electric wire...
Contact details Glen Dimplex Deutschland GmbH, Am Goldenen Feld 18, 95326 Kulmbach (*) For heat pump space heaters and heat pump combination heaters, the rated output Prated is equal to the design load for heating Pdesignh , and the rated heat output of a supplementary capacity for heating sup(Tj ).
Page 32
Contact details Glen Dimplex Deutschland GmbH, Am Goldenen Feld 18, 95326 Kulmbach (*) For heat pump space heaters and heat pump combination heaters, the rated output Prated is equal to the design load for heating Pdesignh , and the rated heat output of a supplementary capacity for heating sup(Tj ).
Page 33
Contact details Glen Dimplex Deutschland GmbH, Am Goldenen Feld 18, 95326 Kulmbach (*) For heat pump space heaters and heat pump combination heaters, the rated output Prated is equal to the design load for heating Pdesignh , and the rated heat output of a supplementary capacity for heating sup(Tj ).
Based on the following conditions, we remedy defects on the unit the online order facility on the Internet (www.dimplex.de/garantiev- due to material and/or manufacturing defects free of charge, pro- erlaengerung).
Page 35
15 Information on the use of data IV. Information on products and new developments. It is very important to Glen Dimplex Thermal Solutions (GDTS) that your data is handled correctly. We should therefore like to GDTS will use your contact details on occasion to show you provide you with information on the data collected when oper- new products and innovations relating to smart homes.
Page 36
English Air-to-water heat pump M Flex 16 Declaration of conformity You can find and download the current CE conformity declaration at: https://glendimplex.de/m DOK4x HOIAO FxDEN · FD 0001 www.glendimplex.de...
Page 37
Air-to-water heat pump M Flex English www.glendimplex.de DOK4x HOIAO FxDEN · FD 0001...
Page 38
English Air-to-water heat pump M Flex DOK4x HOIAO FxDEN · FD 0001 www.glendimplex.de...
Page 39
Air-to-water heat pump M Flex English www.glendimplex.de DOK4x HOIAO FxDEN · FD 0001...
Page 40
Glen Dimplex Deutschland Zentrale Glen Dimplex Deutschland GmbH Am Goldenen Feld 18 D-95326 Kulmbach T +49 9221 709-100 F +49 9221 709-339 dimplex@glendimplex.de www.glendimplex.de Geschäftsstelle Österreich Glen Dimplex Austria GmbH Hauptstraße 71 A-5302 Henndorf am Wallersee T +43 6214 20330 F +43 6214 203304 info@dimplex.at...