Instruction manual General ..............................5 Customer service address ........................5 Warranty ............................5 Scope of delivery ..........................5 Declaration of conformity ......................... 6 Safety ................................. 7 Intended use ............................7 Duration of use ..........................7 Structural change..........................7 Training of th operating personnel ....................7 Transport and handling ........................
All information without guarantee subject to technical changes. For further questions we are of course also available after the purchase at any time. Please use our contact address 1.1 Customer service address NCTE AG Raiffeisenalle 3 D-82041 Oberhaching Phone: +49 (0)89 665 619 0 Email: sales@ncte.de...
_______________________________________________________________________________________ 1.4 Declaration of conformity The manufacturer NCTE AG Raiffeisenalle 3 D-82041 Oberhaching hereby declares that the following product Product designation: Torque sensor series 2000 Trade designation: Series 2000 Model names: 2200-2,5 2200-5 2200-7,5 2200-17,5 2200-75 2200-175 2200-250 2200-500 conforms to the requirements of the EMC Directive 2014/30/EU – including its amendments in force at the time of this declaration.
_______________________________________________________________________________________ Safety Please note the enclosed sheet on the warning notes. 2.1 Intended use The sensors of the series 2000 are designed exclusively for measuring torque and/or speed. The respective load range can be taken from the data sheet and must not be exceeded. Proper use also includes compliance with the commissioning, assembly, operating, ambient and maintenance conditions specified by the manufacturer.
(optional sensor holder). The cable length must not exceed 5m. Using a cable other than the one supplied by NCTE or an identical cable with a different cable length may impair the function of the sensor system.
Check the wiring, connectors and shaft: Every 12 months Repairs and recalibrations can only be carried out by NCTE AG personnel. 3.10 Disposal The device must be returned to NCTE AG, Raiffeisenallee 3, D-82041 Oberhaching for disposal. _______________________________________________________________________________________ Page 9 of 16...
Ø 25 mm Note: In case of overload, the sensor leads to a measurement offset. In this case the sensor must be recalibrated at NCTE AG. The sensor may only be operated within the specified nominal torque range. _______________________________________________________________________________________ Page 10 of 16...
_______________________________________________________________________________________ Load characteristics Model line Series 2100 Limit transverse Limit bending moment Axial force [N] Measuring range force [N] [Nm] 2.5 and 5 1000 1000 17.5 1000 12.5 2600 41.7 4000 89.5 7000 Model line Series 2200 Limit transverse Limit bending moment Axial force [N] Measuring range force [N]...
_______________________________________________________________________________________ Effect of temperature Unit Value 11 Zero point drift over temperature %/10 K < 0.5 Signal drift over temperature %/10 K < 0.5 within nominal temperature range Power supply Unit Value 13 Supply voltage 6 … 15 14 Current consumption (max.) 15 Start-up peak <...
_______________________________________________________________________________________ Dimensions Potentiometer for offset adjustment 2200 (TM-HR-Rd) Round drive Round end with Socket outlet: keyway DIN 748 and DIN 6885 see table Binder Series 712 Female end DIN3121 Male End DIN3121 2100 (TM-HR-Sq) Square drive Flats to secure the sensor housing against rotation Series 2100 Square shaft...
_______________________________________________________________________________________ Wiring diagram Type: Binder Plug Series 712-M9 IP67 (Colour coding acc. to DIN 47100) Colour Description Value Supply voltage V White 6 V – 15 V Brown Output signal analogue Black Supply voltage GND Blue Not required Reference voltage V Grey 2.5 V Connector...
2000 – D25 You can obtain further or additional accessories and special requests in a personal discussion with your contact person for series products by calling +49 (0)89 66 56 19 30 or by e-mail: sales@ncte.de. _______________________________________________________________________________________ Page 15 of 16...
Page 16
Your experts for magnetostrictive sensors...