Sign in today to find solutions:

Forgot your password?

Don't have an account? Sign up

 
Operating Instructions
(GB/USA)
Instrucciones de Manejo
(ESP)
Mode d'emploi
(FR)
Bedienungsanweisung
(GER)
Mode de Emploi
(ITA)
MODELS COVERED IN THIS GUIDE
SABER
MODEL
TYPE
S28
28" Disc
S34
34" Disc
S34SP
34" Cylindrical Head
STRIDE II
MODEL
TYPE
QQS28
28" Disc
QQS34
34" Disc
QQS34SP
34" Cylindrical Head
IPX4
REV.
Y
:
POWER SOURCE
36V Battery
36V Battery
36V Battery
POWER SOURCE
36V Battery
36V Battery
36V Battery
Read these instructions before operating the machine
Antes de usar la máquina lea atentamente el libro de instrucciones
Lire attentivement le mode d'emploi avant la mise en service de la machine
Vor Inbetriebnahme der Maschine Bedienungsanweisung lesen
Leggere queste istruzioni prima di usare la macchina
SABER/STRIDE II 28/34 98570 8/31/99
OWNER'S GUIDE

Summary of Contents

  • Page 1

    Operating Instructions (GB/USA) Instrucciones de Manejo (ESP) Mode d’emploi (FR) Bedienungsanweisung (GER) Mode de Emploi (ITA) MODELS COVERED IN THIS GUIDE SABER MODEL TYPE 28” Disc 34” Disc S34SP 34” Cylindrical Head STRIDE II MODEL TYPE QQS28 28” Disc QQS34 34”...

  • Page 2: Machine Data Log

    Name: Address: Phone Number: For the name and address of your dealer contact: Windsor Ind. The SABER/STRIDE II is a battery powered, self propelled, hard floor scrub- ber intended for commercial use. This appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank.

  • Page 3: Table Of Contents

    OPERATIONS Machine Data Log ......2 Table of Contents ......3 Safety .

  • Page 4: Safety

    Disconnect battery connections before working on machine. • Avoid contact with battery acid. • Use Windsor supplied replacement parts. CAUTION This machine is not suitable for picking up health en- dangering or hazardous dust. WARNING This appliance has been designed for use with the brushes specified by the manufacturer.

  • Page 5: Technical Specifications

    MODEL:SABER/STRIDE II 28/34 Year of Construction: 1998 Nominal Power: 2.88 kW Mass: 850kg Rated Voltage: 36VDC Rated Amperage: 80 amps Cleaning Path: 28” (2 x 14”) S28, QQS28 34” (2 x 17”) S34, QQS34 34” (CYL) S34SP, QQS34SP Drive Motor: .5 hp Brush Motor: .75 hp...

  • Page 6: Operation Controls

    OPERATION CONTROLS Squeegee /Vacuum Switches. Turns on and off the vacuum and squeegee system seperately if desired. Brush Pressure Indicator/Switch. Sets brush pressure on floor with LED’s to show pressure level. One Touch Switch. Activates scrubbing and vacuuming functions. Pressing once turns “ON”. Pressing twice turns “OFF” scrubbing and vacuuming functions.

  • Page 7: Machine Operation

    STARTING MACHINE NOTE: Perform pre-run machine check before operating machine. FOR SAFETY: Before starting machine, make sure that all safety devices are in place and operating properly. Turn the key switch clockwise to the “ON” position. Move the directional control lever in the desired direction.

  • Page 8

    MACHINE OPERATION DOUBLE SCRUB Floors which are heavily soiled or have thick accumulations of floor finish may not clean sufficiently with one pass. In these cases it will be necessary to double scrub. To double scrub, begin scrubbing as usual, but after push- ing number 1, press the squeegee button to turn off vac mo- tor.

  • Page 9: Scrub Brushes

    SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert . This feature will tell the operator when it © is time to replace the scrub brushes. “Perform Alert brushes have bright yellow tufts located on these tufts are pre-trimmed to indicate the length of a worn out brush.

  • Page 10: Squeegee Blades

    MAINTENANCE SCRUB DECK SKIRT AND SQUEEGEE The skirts and squeegee should be inspected for wear and damage. The skirt is self adjusting. Replace skirt when they become cracked, worn, torn or brittle. SQUEEGEE BLADES NOTE: See page 15 of this guide for a complete table on squeegee options.

  • Page 11: Adjusting Squeegee

    ADJUSTING SQUEEGEE Adjusting the squeegee is a two part process. First, the squeegee tool must have correct pitch in order for the squeegee blade to have the same deflection at each tip as well as the center. The pitch adjustment on the SABER/STRIDE II is facilitated by the use of a spirit level mounted on the squeegee tool.

  • Page 12: Batteries

    BATTERIES The batteries provide the power to operate the machine. The standard are four 6 volt batteries rated at 250 A/h at a 6-hour rate. The batteries require regular maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long peri- ods of time, but they can only be charged a certain num- ber of times.

  • Page 13

    TO CHARGE THE BATTERIES CAUTION When servicing machine, avoid contact with bat- tery acid. WARNING Batteries emit hydrogen gas. Explosion or fire can result. Keep sparks and open flame away. Keep covers open when charging. WARNING Wear eye protection and protective clothing when working with batteries.

  • Page 14: Service Schedule

    SERVICE SCHEDULE Before Maintenance Item Starting Check Battery water level the Work Period Check Vac Hose Connections Clean the Squeegee Blades Inspect Brushes or Pads for debris ie: wire, string, wear Inspect Vac fan shut off float screen End of Work Drain &...

  • Page 15

    SQUEEGEE BLADE OPTIONS Desc. 73932 FRONT, STANDARD 73934 REAR, STANDARD 82529 REAR, LINATEX 82528 FRONT, LINATEX 82638 REAR, (FOR TILE) 82637 FRONT, (FOR TILE) 82641 REAR, (FOR BUTTONS) 82640 FRONT, (FOR BUTTONS) 73935 REAR, STANDARD 73900 REAR, LINATEX 73902 REAR, (FOR TILE) 73901 REAR, (FOR BUTTONS) 73936...

  • Page 16: Service Location Details, Squeegee Assembly

    SERVICE LOCATION DETAILS BRUSH HEAD MODELS: S28, S34, QQS28, QQS34 ALL MODELS SQUEEGEE ASSEMBLY REAR ELECTRICAL CONTROL PANEL (REF. BRUSH HEAD CYLINDRICAL HEAD MODELS: S34SP, QQS34SP SQUEEGEE ASSEMBLY CYLINDRICAL HEAD (OPTION) SABER/STRIDE II 28/34 98570 5/1/98...

  • Page 17: Notes

    Part No. Description 70532 SCR, 10-32 X 1/2 PPHMS BLK 80657 PIN, COTTER HAIR .148" DIA X 3/4 87029 WASHER, 5/16 FLAT SS 48012 KNOB, 5/16-18 4 PRONG 82191 PIN, COTTER HAIR .178" DIA X 1" 27756 COVER, FRONT 27770 COVER, FRONT 34 CYL * NOTE: QUANTITY USED FOR S34SP MODEL ONLY SERVICE LOCATION PARTS LIST...

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: