Remote Control; Placing The Television In Standby Mode - Samsung CW-29Z404N Owner's Instructions Manual

AA68-03853A-00Eng_E.asia 4/21/06

Remote Control

(depending on the model)
➢
Operation of remote control may be affected by bright
artificial light near to the TV.
1 1 POWER
Used to switch the TV
on and off.
2 2 Numeric buttons
Used to select channels
directly.
All manuals and user guides at all-guides.com
3:10 PM Page 2
4 4
5 5 MENU
6 6 ... ... / † † / œ œ / √ √
7 7 S.MENU
8 8 TURBO
9 9 P.SIZE
0 0 DUAL I-II
! ! SOURCE
@ @ INFO
# # PRE-CH
Installing Batteries
3 3 -/--
Used to select a channel Remove the cover. Install two AAA
numbered ten or over. size batteries, then replace the cover.
Press this button, then
When the remote control does not
"--" symbol is
operate normally, check that the "+"
displayed. Enter the
and "-" ends of the batteries are inserted correctly or the
two-digit channel
batteries are drained.
➢
number.
$ $ P
/ /
Used to increase or Used to display the next
decrease the volume. or previous stored
channel.
% % EXIT
Used to display the on-
screen menu or return to Used to exit from any
the previous menu. display or return to
normal viewing.
^ ^ MUTE
Used to control the
cursor in the menu. Used to switch the
sound off temporarily. To
turn the sound back on,
Used to display the
press the MUTE,
sound menu.
button.
& & ENTER
Used to select the turbo
While using the on-
sound option.
screen menus, press the
ENTER button to
Used to change the
activate (or change) a
screen size.
particular item.
* * S.MODE
Used to select the
Used to select the
sound mode.
sound effect.
( ( P.MODE
Used to display all of the
Used to select the
available video sources.
picture effect.
) ) TV
Used to view the
Used to return to the TV
channel information and
mode when it is in
setting status you
external input mode.
selected.
a a SLEEP
Used to select a preset
Used to switch
time interval for
repeatedly between the
automatic shut off.
last two channels
displayed.
Do not mix battery types, i.e. alkaline and manganese.
English - 2
Switching the Television On and Off
The mains lead is attached to the rear of the television.
1 Plug the mains lead into an appropriate socket.
➢
The main voltage is indicated on the rear of the
television and the frequency is 50 or 60Hz.
2 Press the "I" button (On/Off) on the front (or side) of the
television.
3 Press the POWER button on the remote control to
switch the television on. The programme that you were
, or
watching last is re-selected automatically. If you have
not yet stored any channels, no clear picture appears.
Refer to "Channel - Auto Store" or "Channel - Manual
Store" on page 4.
➢
If the television is initially powered on, several basic
customer settings proceed automatically. Refer to
"Setup - Plug & Play" on page 3.
4 To switch the television off, press the "I" button (On/Off)
on the front (or side) of the television.

Placing the Television in Standby Mode

The television can be placed in standby mode, in order to
reduce power consumption and wear of the cathode ray
tube. Standby mode can be useful when you wish to
interrupt viewing temporarily (during a meal, for example).
1 Press the POWER button on the remote control while
viewing.
The television is in standby mode.
2 To switch the television back on, simply press it again.
☛
Do not leave the television in standby mode for long
periods of time (when you are away on holiday, for
example). Turn the television off by pressing the "I"
button (On/Off) on the front (or side) of the television. It
is best to unplug the set from the mains and aerial.