Related Manuals for Briggs & Stratton Twin Bagger
Summary of Contents for Briggs & Stratton Twin Bagger
- Page 1 ATTACHMENT OPERATOR’S MANUAL Twin Bagger Mfg. No. Description 1695593 Twin Catcher for 38” Mowers 1737389 Rev.: A...
- Page 2 Hardware/Parts Identification Lower case letters identify pre-assembled and / or pre-existing hardware / parts. Upper case letters identify hardware / parts that are found in the kit (pages 3-4).
- Page 3 Hardware Bag Contents A - CARRIAGE BOLT, B - FLANGE NUT, 5/16”-18 x 2.25” (Qty. 3) 5/16”-18 (Qty. 4) D - CARRIAGE BOLT, C - SPACER 5/16”-18 x .75” (Qty. 1) (Qty. 2) F - NUT, Lock 5/16”-18 (Qty. 1) G - SPEED NUT, E - WING NUT, (Qty.
- Page 4 Hardware Bag Contents AA - BAFFLE, GG - DISCHARGE TUBE, (Qty. 1) (Qty. 1) BB - HITCH ASSEMBLY, (Qty. 1) CC - COVER SUPPORT, (Qty. 1) DD - COLLECTOR BAGS, (Qty. 2) EE - COVER, (Qty. 1) FF - LOWER CHUTE, (Qty.
-
Page 5: Table Of Contents
Table of Contents Operator Safety ................General Warnings ..............Safety Decals ................Assembly..................Blade and Baffle Installation ............Hitch and Frame Installation ............Attach Collector Bags ..............Attach Cover Assembly ............. Lower Discharge Chute Installation ........... Tube Assembly ................. Operation .................. -
Page 6: Operator Safety
Operator Safety Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. General Warnings Safety Decals •... -
Page 7: Assembly
Assembly 4. Insert baffle (AA, Figure 3) into discharge side of WARNING deck through discharge opening. Notched end of baffle should be closest to discharge opening. Secure Before beginning any service work turn off the PTO, notched end of baffle to deck with carriage bolt (A) and set the parking brake, turn off the ignition, and nut (B), finger-tighten at this time. -
Page 8: Hitch And Frame Installation
Assembly Hitch and Frame Installation 3. Slide the hitch assembly (BB, Figure 5) onto the right and left shoulder bolts (H) of the rear frame support (a) . 1. Slide the speed nuts (G, Figure 4) onto rear frame support (a) through square holes so that the threaded side is on the inside of frame support. -
Page 9: Attach Collector Bags
Assembly Attach Collector Bags Attach Cover Assembly 1. Attach collector bags (DD, Figure 7). using grass bag 1. Attach cover assembly (EE, Figure 8) to cover support hangers (a) to bag hanger posts (b). (CC) using hinge pivots (a). Secure cover using hinge pins (K) and hair pins (L). -
Page 10: Lower Discharge Chute Installation
Assembly Lower Discharge Chute Installation 1. Lift mower deflector up (a, Figure 9). 3. Slide the slot of the lower chute (FF) over the carriage bolt (A) and secure with the wing nut (E). 2. Slide the notch of bracket (b) on to deflector hinge rod (c). -
Page 11: Operation
Operation Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. -
Page 12: Collector Removal
Operation 2. Disconnect discharge tube (GG) from lower chute (FF) Collector Removal by moving wire form (a) up and out from puck (b) then slide upper end of tube out of cover. CAUTION 3. Remove hitch and frame assembly (BB) from rear of Operation Without Bagger tractor. -
Page 13: Storage
Storage Storing The Grass Catcher Clean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove any debris from the screen on the underside of the lid. If paint has been scratched on metal parts, touch up with paint, or apply a thin fi lm of oil to prevent corrosion. Store in a dry area. -
Page 14: Warranty
Warranty BRIGGS & STRATTON POWER PRODUCTS GROUP, L.L.C. OWNER WARRANTY POLICY LIMITED WARRANTY Briggs & Stratton Power Products Group, LLC will repair and/or replace, free of charge, any part(s) of the equipment that is defective in material or workmanship or both. Briggs & Stratton Corporation will repair and/or replace, free of charge, any part(s) of the Briggs and Stratton engine* (if equipped) that is defective in material or workmanship or both. - Page 15 Notes...
- Page 16 Briggs & Stratton Yard Power Products Group Copyright © 2012 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved...