Related Manuals for SMC Networks KQB2 Series
Summary of Contents for SMC Networks KQB2 Series
- Page 1 Doc. no. KQ*-OMQ0042-A PRODUCT NAME Metal One-touch Fittings MODEL / Series / Product Number KQB2 Series...
- Page 2 Contents 1. Safety instructions 2 to 3 2. Specific product precautions 4 to 9 3. Specifications 10 to 11 4. Troubleshooting 5. Construction...
- Page 3 Metal One-touch Fittings Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC) , and other safety regulations.
- Page 4 Metal One-touch Fittings Safety Instructions Caution 1.The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary.
- Page 5 (7)The particle generation of the KQB2 series It may cause human injury and/or an accident. depends on the operating conditions and (3)Check if PTFE can be used in application. operating environment.
- Page 6 2. Specific Product Precautions（2） (8)When performing the piping work, turn the tightening tool in the horizontal direction to Mounting/Piping the hex. across flats of the stud so that any moment is not applied to the body. If the tool is in contact with the body, this may Caution cause the stud to come off.
- Page 7 (8)Take note that if nylon tubing and soft nylon tubing are used in a clean room. 2．Specific Product Precautions（3） The antioxidant on the surface of the soft nylon tubing may come off, thereby lowering the Air Supply cleanness level. (9)Do not use in environment where foreign Caution matter may stick to the product or get mixed in the product's interior.
- Page 8 3. Grease is not used for the KQB2 series, Even when products with metal rods can be therefore a greater insertion force is required connected to One-touch fittings, do not use any when the tube is installed.
- Page 9 2．Specific Product Precautions（5） Chamfer Dimension for Female Thread Connection Thread Tightening Method Caution Caution (1) Chamfer dimension for female thread of the (2) Connection thread: R, NPT connection thread First, tighten the fitting by hand, then use a Confirming to ISO 16030 (air pressure fluid dynamics –...
- Page 10 2．Specific Product Precautions（6） Precautions for use with non-SMC tubing Recommended Piping Conditions Caution Caution (1)When used with tubing other than those from SMC, due to their properties, series KQB2 are (1) When connecting piping to the One-touch not subject to warranty. fitting, use pipe length with sufficient margin, in accordance with the piping conditions shown in Fig.
- Page 11 3. Specifications Applicable Tubing Tubing material FEP, PFA, Nylon, Soft nylon, Polyurethane, Polyolefin φ3.2, φ4, φ6, φ8, φ10, φ12, φ16 Tubing O.D. φ1/8", φ5/32", φ1/4", φ5/16", φ3/8", φ1/2" Specifications Fluid Air, Water Note1) Operating pressure range -100kPa～1MPa Note2) Note3) Proof pressure 3.0MPa Ambient and fluid temperature -5～150...
- Page 12 Cross Reference Table of the Inner Sleeve (Inch size) Tubing material Applicable inner sleeve Tubing O.D. TH/TIH TL/TIL Part no. Length (FEP) (Super PFA) TH0402 TJ-0402 φ5/32" TH0425 TJ-0425 TL0403 TJ-0403 TIHB07 TIL07 TJ-0604 φ1/4" TIHA07 TJ-0746 φ5/16" TH0806 TL0806 TJ-0806 20.5 TIHB11...
- Page 13 5. Construction Connection thread: R,NPT Male elbow Male connector Connection thread: G Male elbow Male connector Description Material Release button Stainless steel 304 Guide 1 Stainless steel 304 Guide 2 Stainless steel 304 Chuck Stainless steel 304 Seal Special FKM (Fluoro coated) Male connector body C3604 (Electroless nickel plated) Male elbow body...
- Page 14 Revision history A : - Compliance Requirements: Caution added -Connection thread: R ,NPT Changed notation of tightening method. 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. ©...