Installation Requirements; Tools And Parts; Location Requirements - Whirlpool TUD8700SQ Installation Instructions Manual

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.
All Installations
Tools needed:
Pliers
Phillips
screwdriver
5/16" and 1/4"
nut drivers or
hex sockets
Measuring tape
or ruler
10" adjustable wrench
that opens to
1-1.8" (2.9 cm)
*Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher
Other useful items you may need:
Flashlight
Shallow pan
Parts supplied:
2 - Drain hose clamps
(1 large and 1 small)
Silver Green
Make sure all these parts are included in the literature package.
Parts needed:
90˚ Elbow fitting with
3/8" N.P.T. external threads
(the other end must fit your
water supply line)
Other parts you may also need:
1-1/2"–2"
(38.1– 5.0 cm)
Screw-type
clamps (3 max)
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that
electrical connections be made by a licensed electrical installer.
® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
Flat-blade
screwdriver
Utility knife
UL listed or CSA
approved twist-on
wire connectors*
Small level
5/8" open-end
wrench
Bath towel
Wood block
Drain hose 2 - #10 x 1/2"
Phillips-head
screws
Teflon® tape or pipe joint
compound
Side mounting kit Masking or
for solid surface duct tape
countertops
(Part No. 8212560)
In addition, for first time installations
Tools needed:
Electric drill
with 1/2", 3/4"
and 1-1/2" hole
saw bits
Parts needed:
Copper tubing (3/8" See "Electrical Requirements" section
O.D. suggested) or
For Direct Wire:
flexible braided
use UL listed or
water supply line
CSA approved
conduit
connector to
fit 7/8" (2.2 cm)
hole

Location Requirements

Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.
Check location where dishwasher will be installed. The
location must provide:
• easy access to water, electricity and drain.
• convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum
clearance between the side of the dishwasher door
and the wall or cabinet.
• square opening for proper operation and appearance.
• cabinet front perpendicular to floor.
• level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the
dishwasher opening is uneven (example: flooring
extends only partway into opening).
NOTE: To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section.
Small
tubing cutter Wire stripper
For Power Supply
Cord: use UL
listed power
supply cord kit
marked for use
with dishwasher
3