Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for WAGNER W 350
Summary of Contents for WAGNER W 350
- Page 1 WOOD & METAL SPRAYER W 350 OPERATING INSTRUCTIONS wagner-group.com...
- Page 2 W 350...
- Page 3 W 350 click ...
- Page 4 W 350 ...
- Page 5 W 350 4 3 2...
-
Page 6: Table Of Contents
W 350 Contents 1. Explanation of symbols used ........... . .1 2. -
Page 7: Explanation Of Symbols Used
W 350 MANY THANKS FOR PLACING YOUR TRUST IN US We would like to congratulate you on purchasing this brand product from Wagner; we are sure that you will enjoy working with it greatly. We would be happy to be of assistance if you have any questions, suggestions or requests. - Page 8 W 350 b) Avoid physical contact with earthed surfaces such as pipes, heating elements, stoves and refrigerators. The risk through electric shock increases if your body is earthed. c) Keep the equipment away from rain and moisture. The risk of an electric shock increases if water penetrates electrical equipment.
- Page 9 W 350 f) Wear suitable clothing. Do not wear wide clothing or jewellery. Keep your hair, clothes and gloves away from moving parts. Loose clothing, jewellery or long hair can be caught in moving parts. g) Do not lull yourself into a false sense of security and do not think yourself above the safety rules for electric tools, even if you are familiar with the electric tool following extensive practical experience.
-
Page 10: Safety Instructions For Spray Guns
Check the nozzle seal before each use. • When working with the W 350 indoors as well as outdoors ensure that no solvent vapors are sucked in by the spray gun. •... -
Page 11: Description/ Scope Of Delivery
W 350 4. Description/ Scope of delivery Description/ Scope of delivery (Fig. 1) 1) Air Cap 2) Nozzle 3) Union nut 4) Spray gun front part 5) Trigger 6) Spray gun rear part 7) Air filter cover 8) ON/OFF switch (located on both sides) -
Page 12: Start-Up
Press the ON/OFF switch at the device. • Pull the trigger. The W 350 has a two-stage trigger. In the first stage the turbine is started. If the trigger is pressed further, the material is transported. 9. Adjusting the desired Spray Setting WARNING! Danger of injury! Never pull the trigger while adjusting the air cap. -
Page 13: Taking Out Of Operation And Cleaning
W 350 setting. Important: Begin spraying outside of the target area and avoid interruptions inside the target area. • Correct (Fig. 7a) Be sure to hold the spray gun at an even distance of approx. 5 - 15 cm to the target object. -
Page 14: Maintenance
W 350 2) Put the nozzle (fig. 9 B, 3) onto the gun body and find the correct position by turning it. 3) Put the air cap onto the nozzle and tighten it using the union nut. 4) Place the container seal from below on the suction tube and slide it over the collar, while turning the container seal slightly. -
Page 15: Accessories
2315 539 15. Accessories The CLICK&PAINT SYSTEM with additional spray attachments and accessories offers the right tool for each work. Further information about the WAGNER range of products for renovating is available under www.wagner-group.com 16. Correction of Malfunctions Problem Cause Remedy •... -
Page 16: Technical Data
W 350 Problem Cause Remedy • Coating Too much coating material ➞ Reduce the material material causes applied. volume "paint tears" • Too much fog of Distance to the object too large ➞ Reduce distance • coating material Too much coating material ➞... -
Page 17: Environmental Protection
The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. - Page 18 W 350...
- Page 19 W 350...
- Page 20 F 91 883 19 59 DELOS S.A. Gonetsa area Markopoulo Mesogaias 190 03 Attiki, Greece P.O. BOX 293 T 22990 41056 F 22990 41059 Part. No. 2411988 B 05/2020_RS © Copyright by J.Wagner GmbH Not responsible for errors and changes...